engine oil Citroen C5 2016 (RD/TD) / 2.G Owner's Guide

Page 351 of 366

8
Practical information
3

Repair procedure


1. Sealing




)
Switch off the ignition.




)
Turn the selector A
to the
"sealant" position.

)
Check that the switch B
is in
position "O"
.


Avoid removing any foreign bodies
which have penetrated into the tyre.


)
Uncoil the white pipe G
fully.

)
Unscrew the cap from the white pipe.

)
Connect the white pipe to the valve of the
tyre to be repaired.


Take care, this product is harmful
(e.g. ethylene-glycol, colophony...) if
swallowed and causes irritation to the
eyes.
Keep this product out of the reach of
children.


)
Connect the compressor's electric plug to
the vehicle's 12 V socket.

)
Start the vehicle and leave the engine
running.


Do not start the compressor before
connecting the white pipe to the tyre
valve: the sealant product would be
expelled through the pipe.

Page 353 of 366

8
Practical information
5

2. Infl ation




)
Turn the selector A
to the "air"
position.

)
Uncoil the black pipe H
fully.

)
Connect the black pipe to the valve of the
wheel.



)
Connect the compressor's electric plug to
the vehicle's 12 V socket.

)
Start the vehicle again and leave the
engine running.


As soon as possible, go to a CITROËN
dealer or a qualified workshop.
You must inform the technician that you
have used this kit. After inspection, the
technician will advise you on whether
the tyre can be repaired or if it must be
replaced.


)
Adjust the pressure using the compressor
(to inflate: switch B
in position "I"
; to
deflate: switch B
in position "O"
and press
button C
), in accordance with the vehicle's
tyre pressure label (located on the left
hand door aperture).
A loss of pressure indicates that the
puncture has not been fully plugged;
contact a CITROËN dealer or qualified
workshop for assistance.

)
Remove and stow the kit.

)
Drive at reduced speed (50 mph [80 km/h]
max) limiting the distance travelled to
approximately 120 miles (200 km).

Page 354 of 366

Practical information
6

Removing the cartridge




)
Stow the black pipe.

)
Detach the angled base from the white pipe.

)
Support the compressor vertically.

)
Unscrew the cartridge from the bottom.


Beware of discharges of fluid.
The expiry date of the fluid is indicated
on the cartridge.
The sealant cartridge is designed for
single use; even if only partly used, it
must be replaced.
After use, do not discard the cartridge
into the environment, take it to an
authorised waste disposal site or a
CITROËN dealer.
Do not forget to obtain a new sealant
cartridge, available from CITROËN
dealers or from a qualified workshop.



Checking tyre pressures / inflating accessories


You can also use the compressor, without
injecting any product, to:


- check or adjust the pressure of your tyres,

- inflate other accessories (balls, bicycle
tyres...).




)
Turn the selector A
to the "Air"
position.

)
Uncoil the black pipe H
fully.

)
Connect the black pipe to the valve of the
wheel or accessory.
If necessary, fit one of the adaptors
supplied with the kit first.



)
Connect the compressor's electrical
connector to the vehicle's 12 V socket.

)
Start the vehicle and let the engine run.

)
Adjust the pressure using the compressor
(to inflate: switch B
in position "I"
; to
deflate: switch B
in position "O"
and press
button C
), according to the vehicle's tyre
pressure label or the accessory's pressure
label.

)
Remove the kit then stow it.

Page:   < prev 1-10 11-20 21-30