battery Citroen C5 DAG 2009.5 (RD/TD) / 2.G Owner's Manual

I
34M O N I T O R I N G

Warning lamp is on Cause Action/Observations

Low fuel
level fi xed. When it fi rst comes on there
remains
approximately
5 litres of
fuel in the tank. You must refuel as soon as possible to
avoid running out of fuel.
This warning lamp wil come on every time
the ignition is switched on, until a suffi cient
addition of fuel is made.
Fuel tank capacity: 71 litres.
Never continue to drive until you run out
of fuel, this could damage the emission
control and injection systems.

Maximum
coolant
temperature fi xed red.
The temperature of the
cooling system is too high. Stop as soon as it is safe to do so.
Wait until the engine has cooled down
before topping up the level, if necessary.
If the problem persists, contact a
CITROËN dealer.

Battery
charge fi xed. The battery charging circuit
has a fault (dirty or loose
terminals, slack or cut
alternator belt, ...). This lamp should switch off when the
engine is started.
If it does not switch off, contact a
CITROËN dealer.
+
Seat belt not
fastened/
unfastened fi xed.
The driver and/or the front/
rear passenger has not
fastened or has unfastened
their seat belt. Pull the strap then insert the tongue in the
buckle.

Seat belts
not fastened/ unfastened fi xed, associated
with the seat belt not fastened/unfastened
warning lampl. The illuminated dots represent the not
fastened/unfastened passengers.
They come on:
- fi xed for 30 about seconds on starting the
vehicle,
- fi xed from 0 to 12 mph (0 to 20 km/h) when driving,
-
fl ashing above 12 mph (20 km/h), accompanied
by an audible signal for about 120 seconds.

III
!
57
C O M F O R T
Changing the battery
The remote control is supplied by a
6V-28L battery, which is supplied.
Information on the display indicates
when it is time to replace this battery.
Unclip the casing then replace the
battery.
The remote control must then be re-
initialised, see below. Always switch off the program-
mable heating while fi lling with
fuel to avoid any risk of fi re or ex-
plosion.
To avoid any risk of poisoning and
asphyxiation, the programmable
heating must not be used, even
for short periods, in an enclosed
space such as a garage or work-
shop which is not equipped with an
exhaust gas extraction system.
Do not park the vehicle on an
infl ammable surface (dry grass,
dead leaves, paper…), there is a
risk of fi re.
The programmable heating sys-
tem is supplied by the vehicle's fuel
tank. Before use, ensure that the
quantity of fuel remaining is suf-
fi cient. If the fuel tank is at the re-
serve, we strongly advise that you
do not programme the heating.
Do not discard the used bat-
teries, take them to an ap-
proved collection point.
Reinitialising the remote control
If the vehicle's battery is disconnect-
ed or the remote control's battery is
replaced, the remote control must
be reinitialised.
After switching on the power, press
button 4 (OFF) for 1 second within
the next 5 seconds. If the operation
has taken place correctly the mes-
sage "OK" is displayed on the re-
mote control screen.
If a problem occurs, the message

"FAIL" appears. Repeat the operation.
In addition, your programmable
heating can be to pre-heat your
vehicle's passenger compart-
ment. The interior volumetric protection
alarm movement sensor may be
disturbed by the fl ow of air from
the programmable heating when
it is in operation.
To avoid any unexpected trigger-
ing of the alarm during use of the
programmable heating, it is ad-
visable to deactivate the interior
volumetric protection.

III
61
C O M F O R T
Storing driving positions
System which takes into account the
settings of the driver's seat and air
conditioning. It enables you to store
up to two positions using the buttons
on the side of the driver's seat. Storing a position
Using buttons M/1/2

 Switch on the ignition.

 Adjust your seat.

 Press button M , then press but-
ton 1 or 2 within four seconds.
An audible signal is heard indicating
that the settings have been stored.
Storing a new position cancels the
previous position.
Recalling a stored position
Ignition on or engine running

 Briefl y press button 1 or 2 to re-
call the corresponding position.
An audible signal is heard indicating
the end of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery. For your safety, avoid storing a
driving position while driving.
REAR HEAD RESTRAINTS
The rear head restraints can be re-
moved and have two positions:
- high, position for use,
- low, storage position.
To raise a head restraint, pull it up-
wards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high
position, push the lug and pull it
upwards.
To refi t it, engage the head restraint
rods in the holes taking care to re-
main in line with the seat back.
Never drive with the head restraints
removed, they must be in place
and correctly adjusted.

III
61
C O M F O R T
Storing driving positions
System which takes into account the
settings of the driver's seat and air
conditioning. It enables you to store
up to two positions using the buttons
on the side of the driver's seat. Storing a position
Using buttons M/1/2

 Switch on the ignition.

 Adjust your seat.

 Press button M , then press but-
ton 1 or 2 within four seconds.
An audible signal is heard indicating
that the settings have been stored.
Storing a new position cancels the
previous position.
Recalling a stored position
Ignition on or engine running

 Briefl y press button 1 or 2 to re-
call the corresponding position.
An audible signal is heard indicating
the end of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery. For your safety, avoid storing a
driving position while driving.
REAR HEAD RESTRAINTS
The rear head restraints can be re-
moved and have two positions:
- high, position for use,
- low, storage position.
To raise a head restraint, pull it up-
wards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high
position, push the lug and pull it
upwards.
To refi t it, engage the head restraint
rods in the holes taking care to re-
main in line with the seat back.
Never drive with the head restraints
removed, they must be in place
and correctly adjusted.

IV
69
O P E N I N G S
Malfunction
Following disconnection of the ve-
hicle battery, replacement of the re-
mote control battery or in the event
of a remote control malfunction, you
can no longer unlock, lock or locate
your vehicle.

 First of all, use the key in the lock
to unlock or lock your vehicle.

 Then, reinitialise the remote con-
trol.
If the problem persists, contact a
CITROËN dealer as soon as pos-
sible.
Reinitialisation

 Switch off the ignition.

 Turn the key to position 2 (
Drive
) .

 Press the closed padlock imme-
diately for a few seconds, until
the operation requested is trig-
gered.

 Switch off the ignition and re-
move the key from the ignition
switch.
The remote control is fully opera-
tional again. Battery ref.: CR0523/3 volts.
This replacement battery is avail-
able from CITROËN dealers.
If the battery is fl at,
you are informed by
lighting of this warn-
ing lamp, an audible
signal and a message on the multi-
function screen.

 Unclip the casing using a coin at
the notch.

 Slide the fl at battery out of its lo-
cation.

 Slide the new battery into its lo-
cation observing the original di-
rection.

 Clip the casing.

 Reinitialise the remote control.
Changing the battery

IV
76
O P E N I N G S
Unlocking

 Press button A again to unlock
the vehicle.
The red indicator lamp on the button
switches off.
If the vehicle is locked or dead-
locked from the outside, the red in-
dicator lamp fl ashes and button A
is inactive.

 In this case, use the remote
control or the key to unlock the
vehicle.
Automatic central locking
System which provides full automatic locking or unlocking of the doors and
the boot while driving.
You can activate or deactivate this
function. Locking
When the speed exceeds 6 mph
(10 km/h), the doors and the boot
lock automatically.
If one of the doors is open, the auto-
matic central locking does not take
place.
If the boot is open, the automatic
central locking of the doors is active.
Unlocking

 Above 6 mph (10 km/h), press
button A to unlock the doors and
the boot temporarily.
Activation

 Press button A for more than
two seconds.
A confi rmation message appears on
the instrument panel screen, accom-
panied by an audible signal.
Deactivation

 Press button A again for more
than two seconds.
A confi rmation message appears on
the instrument panel screen, accom-
panied by an audible signal. Emergency control
System which locks or unlocks the
doors mechanically in the event of
a malfunction of the battery or of the
central locking.
Locking the driver's door

 Insert the key in the lock, then
turn it to the right.
Unlocking the driver's door

 Insert the key in the lock, then
turn it to the left.
Locking the front and rear
passenger doors

 Insert the key in the lock, located
on the edge of the door, then turn
it one eighth of a turn .
Unlocking the front and rear
passenger doors

 Pull the interior door opening
control.

IV
77
O P E N I N G S
BOOT (SALOON)

 Press upwards on lever 1 and lift
up the boot lid. With the vehicle stationary, this is
carried out using:
- The remote control.
- The key in a door lock.
- The interior central locking/un-
locking control.
The boot automatically locks when
the vehicle is moving at a speed of
over 6 mph (10 km/h), even if auto-
matic central locking is deactivated.
It is unlocked when a door is opened
or when the central locking button is
pressed (speed lower than 6 mph
(10 km/h)).
Opening
Locking/unlocking Emergency tailgate release
System for mechanical unlocking of
the boot in the event of a battery or
central locking malfunction.
Unlocking

 Fold back the rear seats to gain
access to the lock from inside
the boot.

 Insert a small screwdriver into
hole A of the lock to unlock the
tailgate.

 Push the white part, located in-
side the lock, to the left to unlock
the boot.

IV
80
O P E N I N G S
PANORAMIC SUNROOF (SALOON)
Sunroof closed
- Press B to fi rst notch: tilting.
- Press B to second notch: auto-
matic complete tilting.
- Press A to fi rst notch: sliding to-
wards rear.
- Press A to second notch: auto-
matic total sliding towards rear. Sunroof open
- Press
B to fi rst notch: closure.
- Press B to second notch: auto-
matic total closure.
Always remove the ignition key
when leaving the vehicle, even if
for a short time .
In the event of anything being
caught by the sunroof closing, you
must reverse the roof movement.
Do this by reversing the position of
the control switch .
When the driver is operating the
sunroof, they must always make
sure that the passengers are not
preventing it from closing properly.
The driver must ensure that pas-
sengers use the sunroof control
correctly.
Pay special attention to where chil-
dren are when operating the sunroof.
The fi tting of a sunroof as an acces-
sory is prohibited
Operation
Tilted sunroof
- Press A to fi rst notch: closure.
- Press A to second notch: auto-
matic total closure.
Your sun roof is fi tted with a manually-
operated blind.
Anti-pinch
An anti-pinch device stops the sun
roof from closing, whether sliding or
tilting. If it meets an obstacle, it re-
opens. Reinitialisation
After a battery disconnection or if
there has been a malfunction, you
have to re-initialise the anti-pinch
function.

 move control B until the roof is in
the complete tilting position,

 keep control B pressed down for
a minimum of 1 second.

During these operations, the anti-
pinch function does not operate
.

IV
81
O P E N I N G S
PANORAMIC SUNROOF (TOURER)
This comprises a tinted glass pan-
oramic area 1 to improve brightness
and vision in the passenger com-
partment.
It is fi tted with an electric blind 2 to
help maintain a comfortable temper-
ature and reduce noise. Opening

 Press control A .
Pressing to the 1st notch allows you
to open the blind step by step.
Pressing to the 2nd notch allows
you to fully open the blind.
The blind stops in the closest pre-
defi ned position (11 positions) as
soon as you release the control.
Closing

 Press control B .
Press to the fi rst notch to close the
blind step by step.
Press to the second notch to close
the blind completely.
The blind stops at the nearest pre-
set position (11 positions) as soon
as you release the control. After a battery disconnection, or if
there has been a malfunction, you
have to re-initialise the anti-pinch
function:

 press control B to the 2nd notch
(fully closed),

 wait until the blind is fully
closed,


press control B for at least 3 sec-
onds.
If the blind opens randomly during a
closing operation, and straight after
the blind stops:

 Press control B until the blind
closes fully.

During these operations, the anti-
pinch function does not operate.
In the event of anything being
caught when the blind is moving,
you must reverse the movement of
the blind. To do so, reverse the po-
sition of the control.
When the driver is operating the
blind, he or she must always make
sure that the passengers are not
preventing it from closing properly.
The driver must ensure that pas-
sengers use the blind correctly.
Pay particular attention to children
when operating the blind .
Anti-pinch
If the blind meets an obstacle whilst
closing, it stops and opens partially
again.
You must re-initialise the anti-pinch
function within 5 seconds of the
blind stopping:

 press control B until the blind is
fully closed (closing in steps of a
few centimetres).
SEQUENTIAL ELECTRIC BLIND

V
85
V I S I B I L I T Y

C. Foglamps selection ring.
The foglamps operate with the side-
lamps and the dipped and main
beam headlamps.
-
1 st turn forwards: rear foglamps on.
- 1 st turn rearwards: rear foglamps off.
- 1 st turn forwards: front foglamps on.
- 2 nd turn forwards: rear foglamps on.
- 1 st turn rearwards: rear foglamps off.
- 2 nd turn rearwards: front foglamps off.
Model with rear foglamps
only
Model with front and rear
foglamps In good or rainy weather, both day
and night, the front foglamps and
the rear foglamps are prohibited. In
these situations, the power of their
beams may dazzle other drivers.
They should only be used in fog or
snow.
In these weather conditions, it is
your responsibility to switch on the
foglamps and dipped headlamps
manually as the brightness sensor
may detect suffi cient light.
Do not forget to switch off the front
foglamps and the rear foglamps
when they are no longer necessary.
Lamps on buzzer
The triggering of an audible signal
when a front door is opened warns
the driver that he has forgotten to
switch off his vehicle's lamps, with
the ignition off and in manual lamps
mode.
In this case, switching off the lamps
stops the audible signal.
With the ignition off, if the dipped
headlamps remain on, they will
switch off automatically after thirty
minutes to prevent discharging of
the battery.