service indicator Citroen C5 DAG 2010.5 (RD/TD) / 2.G Owner's Manual

Page 28 of 336

I
30M O N I T O R I N G
Warning and indicator lamps
Visual indicators which inform the driver of the occurrence of a
fault (warn-
ing lamp) or of the operation of a system (operation or deactiva tion indicator
lamp).

Warning lamp is on Cause Action/Observations

STOP fi xed,
associated with
another warning lamp. It is associated with a
punctured tyre or the engine
coolant temperature.
Stop as soon as it is safe to do so.
Park, switch off the ignition and call a
CITROËN dealer.

Service temporarily.
A minor fault has occurred
for which there is no specifi c
warning lamp. Identify the fault by reading the message
shown on the screen, such as, for example:
- the closing of the doors, boot, rear
screen or bonnet,
- the remote control battery,
- the tyre pressures,
- saturation of the particle emission fi lter (Diesel).
For any other faults, contact a CITROËN
dealer.
fi xed. A major fault has occurred
for which there is no specifi c
warning lamp. Identify the fault by reading the message
shown on the screen and contact a
CITROËN dealer.
When the ignition is switched on
Certain warning lamps come on for a few seconds wh
en the ignition is switched on.
When the engine is started, these warning lamps should switc h off.
If they remain on, before moving off, consult the information on the warning
lamp concerned.
Associated warnings
The switching on, fi xed or fl ashing, of certain warning la mps may be accompa-
nied by an audible signal and a message on the screen. Warning lamps
When the engine is running or the ve-
hicle is being driven, the switching on
of one of the following warning lamps
indicates a fault which requires ac-
tion on the part of the driver.
The switching on of a warning lamp is
always accompanied by the display-
ing of an additional message, to as-
sist you in identifying the anomaly.
If you encounter any problems, do not
hesitate to contact a CITROËN dealer.

Page 31 of 336

I
30M O N I T O R I N G
Warning and indicator lamps
Visual indicators which inform the driver of the occurrence of a
fault (warn-
ing lamp) or of the operation of a system (operation or deactiva tion indicator
lamp).

Warning lamp is on Cause Action/Observations

STOP fi xed,
associated with
another warning lamp. It is associated with a
punctured tyre or the engine
coolant temperature.
Stop as soon as it is safe to do so.
Park, switch off the ignition and call a
CITROËN dealer.

Service temporarily.
A minor fault has occurred
for which there is no specifi c
warning lamp. Identify the fault by reading the message
shown on the screen, such as, for example:
- the closing of the doors, boot, rear
screen or bonnet,
- the remote control battery,
- the tyre pressures,
- saturation of the particle emission fi lter (Diesel).
For any other faults, contact a CITROËN
dealer.
fi xed. A major fault has occurred
for which there is no specifi c
warning lamp. Identify the fault by reading the message
shown on the screen and contact a
CITROËN dealer.
When the ignition is switched on
Certain warning lamps come on for a few seconds wh
en the ignition is switched on.
When the engine is started, these warning lamps should switc h off.
If they remain on, before moving off, consult the information on the warning
lamp concerned.
Associated warnings
The switching on, fi xed or fl ashing, of certain warning la mps may be accompa-
nied by an audible signal and a message on the screen. Warning lamps
When the engine is running or the ve-
hicle is being driven, the switching on
of one of the following warning lamps
indicates a fault which requires ac-
tion on the part of the driver.
The switching on of a warning lamp is
always accompanied by the display-
ing of an additional message, to as-
sist you in identifying the anomaly.
If you encounter any problems, do not
hesitate to contact a CITROËN dealer.

Page 33 of 336

I
30M O N I T O R I N G
Warning and indicator lamps
Visual indicators which inform the driver of the occurrence of a
fault (warn-
ing lamp) or of the operation of a system (operation or deactiva tion indicator
lamp).

Warning lamp is on Cause Action/Observations

STOP fi xed,
associated with
another warning lamp. It is associated with a
punctured tyre or the engine
coolant temperature.
Stop as soon as it is safe to do so.
Park, switch off the ignition and call a
CITROËN dealer.

Service temporarily.
A minor fault has occurred
for which there is no specifi c
warning lamp. Identify the fault by reading the message
shown on the screen, such as, for example:
- the closing of the doors, boot, rear
screen or bonnet,
- the remote control battery,
- the tyre pressures,
- saturation of the particle emission fi lter (Diesel).
For any other faults, contact a CITROËN
dealer.
fi xed. A major fault has occurred
for which there is no specifi c
warning lamp. Identify the fault by reading the message
shown on the screen and contact a
CITROËN dealer.
When the ignition is switched on
Certain warning lamps come on for a few seconds wh
en the ignition is switched on.
When the engine is started, these warning lamps should switc h off.
If they remain on, before moving off, consult the information on the warning
lamp concerned.
Associated warnings
The switching on, fi xed or fl ashing, of certain warning la mps may be accompa-
nied by an audible signal and a message on the screen. Warning lamps
When the engine is running or the ve-
hicle is being driven, the switching on
of one of the following warning lamps
indicates a fault which requires ac-
tion on the part of the driver.
The switching on of a warning lamp is
always accompanied by the display-
ing of an additional message, to as-
sist you in identifying the anomaly.
If you encounter any problems, do not
hesitate to contact a CITROËN dealer.

Page 37 of 336

I
37
M O N I T O R I N G
Service indicator
This information is displayed for a
few seconds when the ignition is
switched on. It informs the driver
when the next service is due, in ac-
cordance with the manufacturer's
servicing schedule.
The point at which the service is due
is calculated from the last indicator
zero reset. It is determined by two
parameters:
- the distance travelled,
- the time elapsed since the last service.
More than 1 800 miles (3 000 km)
remain before the next service is due
When the ignition is switched on, no
service information appears on the
instrument panel central screen.
Between 600 miles (1 000 km)
and 1 800 miles (3 000 km) remain
before the next service is due
For 7 seconds after the ignition is
switched on, the spanner symbolis-
ing the service operations comes on.
The instrument panel central screen
indicates the distance remaining be-
fore the next service is due.

Example: 1 700 miles remain be-
fore the next service is due.
For 7 seconds after the ignition is switched
on, the central screen indicates:
Less than 600 miles (1 000 km)
remain before the next service is due

Example: 500 miles remain before
the next service is due.
For 7 seconds after the ignition is
switched on, the central screen in-
dicates: Service overdue
For 7 seconds after the ignition is
switched on,
the spanner fl ashes
to indicate that the service must be
carried out as soon as possible.

Example: the service is overdue by
300 miles.
For 7 seconds after the ignition is switched
on, the central screen indicates:

The spanner remains on in the
screen to indicate that a service
must be carried out soon.
The distance remaining may be
weighted by the time factor, de-
pending on the driver's driving
habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.

The spanner remains on in the
screen to indicate that a service
should have been carried out.

Page 38 of 336

I
38M O N I T O R I N G
Service indicator zero reset
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count. Engine oil level indicator
System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is indicated for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by displaying of the
message "Oil level incorrect".
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by displaying of the
message "Oil level measurement in-
valid". Consult a CITROËN dealer.

Page 39 of 336

I
38M O N I T O R I N G
Service indicator zero reset
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count. Engine oil level indicator
System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is indicated for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by displaying of the
message "Oil level incorrect".
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by displaying of the
message "Oil level measurement in-
valid". Consult a CITROËN dealer.

Page 40 of 336

I
39
M O N I T O R I N G
Engine oil temperature gauge
Under normal operating conditions,
the bars should be within section
1 .
In severe operating conditions, the
bars may extend into section 2 .
In this event, slow down, and if neces-
sary, stop the engine and check the
levels (see corresponding chapter). Coolant temperature
indicator
Under normal operating conditions,
the bars should be within section
1 .
In severe operating conditions, the
bars may extend into section 2 , the
engine coolant temperature warning
lamp A and the STOP warning lamp
will light up, stop immediately .
Switch off the ignition. The cooling
fan may continue to operate for a
certain time .
Consult a CITROËN dealer.
If the SERVICE warning lamp lights
up, check the levels (see correspond-
ing chapter). On horizontal ground, the lighting of
the fuel low warning lamp warns you
that you are at the reserve level.
A message alert is displayed on the
instrument panel.
Fuel gauge indicator

Page 79 of 336

IV
!
73
A C C E S S
ALARM *
System which protects and provides
a deterrent against theft and break-
ins. It provides the following types of
monitoring.
- Exterior perimeter
The system checks for opening of
the vehicle.
The alarm is triggered if anyone tries
to open a door, the boot, the bonnet...
- Interior volumetric
The system checks for any variation in
the volume in the passenger compart-
ment.
The alarm is triggered if anyone breaks
a window, enters the passenger com-
partment or moves inside the vehicle.
- Tilt
The system checks for any change
in the attitude of the vehicle.
The alarm is triggered if the vehicle
is lifted, moved or knocked. Locking the vehicle with full
alarm system
Activation

 Switch off the ignition and get out
of the vehicle.

 Press the locking button on the
remote control.
The monitoring system is active: the
indicator lamp on the button fl ashes
once per second.
After the locking button on the re-
mote control is pressed, the exterior
perimeter monitoring is activated
after a delay of 5 seconds and the
interior volumetric and anti-tilt moni-
toring after a delay of 45 seconds.
If an opening (door, boot...) is not
closed fully, the vehicle is not locked
but the exterior perimeter monitor-
ing will be activated after a delay of
45 seconds at the same time as the
interior volumetric and anti-tilt moni-
toring. Deactivation

 Press the unlocking button on
the remote control.

The alarm system is deactivated: the in-
dicator lamp on the button switches off.
Locking the vehicle with
exterior perimeter monitoring
only
Deactivate the interior volumetric
and anti-tilt monitoring to avoid un-
wanted triggering of the alarm in
certain cases such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transport by sea.
Self-protection function
The system checks for the
putting out of service of its
components.
The alarm is triggered if the battery,
the central control or the siren wiring
are put out of service or damaged.
For all work on the alarm system,
contact a CITROËN dealer. Deactivation of the interior
volumetric and anti-tilt
monitoring

 Switch off the ignition.

 Within ten seconds, press the
button until the indicator lamp is
lit continuously.

 Get out of the vehicle.

 Press the locking button on the
remote control immediately.
The exterior perimeter monitoring alone
is activated: the indicator lamp on the
button fl ashes once per second.
To be effective, this deactivation
must be carried out each time the
ignition is switched off.

Page 132 of 336

VIII
113
S A F E T Y
DIRECTION INDICATORS

 Left: lower the lighting stalk be-
yond the point of resistance.

 Right: raise the lighting stalk be-
yond the point of resistance.
"Motorway" function

 Press briefl y upwards or down-
wards, without going beyond the
point of resistance; the direction
indicators will fl ash 3 times.
HAZARD WARNING LAMPS
A visual warning by means of the di-
rection indicators to alert other road
users to a vehicle breakdown, tow-
ing or accident.
Automatic operation of
hazard warning lamps
When braking in an emergency,
depending on the deceleration, the
hazard warning lamps come on au-
tomatically.
They switch off automatically the
fi rst time you accelerate.

 You can also switch them off by
pressing the button. Audible warning to alert other road
users to an imminent danger.
Selection of the left or right direction
indicators to signal a change of di-
rection of the vehicle.

 Press this button, the direction
indicators fl ash.
They can operate with the ignition off.
 Press the left or right-hand part
of the fi xed centred controls
steering wheel.
Use the horn moderately and only
in the following cases:
- immediate danger,
-
- when approaching an area where there is no visibility.
This system allows you to make an
emergency or assistance call to the
emergency services or to the dedi-
cated CITROËN service.
For more information on the use of
this function, refer to the "Audio and
telematics" section.
EMERGENCY OR ASSISTANCE CALL

Page 174 of 336

IX
153
D R I V I N G
LANE DEPARTURE WARNING SYSTEM
System which detects the involun-
tary crossing of longitudinal traffi c
lane markings on the ground (solid
or broken line).
Sensors, fi tted below the front bum-
per, trigger a warning if the vehicle
drifts over a lane marking (speed
higher than 50 mph (80 km/h)).
This system is particularly useful on
motorways and main roads.
Activation

 Press button A , the indicator
lamp comes on.
Deactivation

 Press button A again, the indica-
tor lamp switches off.
The status of the system remains
in the memory when the ignition is
switched off. Detection
You are warned by the vibration of
the driver's seat cushion:
- on the right-hand side, if the
marking on the ground has been
crossed on the right,
- on the left-hand side, if the mark- ing on the ground has been
crossed on the left.
No warning is transmitted while the
direction indicator is active and for
approximately 20 seconds after the
direction indicator is switched off.
A warning may be transmitted if a direc-
tion marking (e.g. arrow) or non-stan-
dard marking (e.g. graffi ti) is crossed. Operating fault
In the event of a malfunction, the
service warning lamp comes on,
accompanied by an audible signal
and a message on the multifunction
screen.
Consult a CITROËN dealer.
The lane departure warning sys-
tem cannot, in any circumstances,
replace the need for vigilance and
responsibility on the part of the
driver.
The detection may be impeded:
- if the sensors are dirty (mud, snow...),
- if the markings on the ground are worn,
- if there is little contrast between the markings on the ground and
the road surface.

Page:   1-10 11-20 next >