warning Citroen C5 RHD 2012 (RD/TD) / 2.G Service Manual

IX
135
DRIVING


SITUATION



CONSEQUENCES




4

Display of messages " Parking brake faulty
"
and " Anti roll-back
fault
" and of the following
warning lamps:

and/or

fl ashing

- The automatic functions are deactivated.

- The hill start assist is not available.
To apply the electric parking brake:


)
Immobilise the vehicle and switch off the ignition

)
Pull the control lever for at least 5 seconds or until maximum
application.

)
Switch on the ignition and check that the electric parking brake
warning lamps are on.


- Application may take longer than in normal operation.

- If warning lamp (!) fl ashes or if the warning lamps do not come
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer or a qualifi ed workshop.
To release the electric parking brake:


)
Switch on the ignition.

)
Push the control lever and hold it for approximately 3 seconds.


5

Display of message " Parking brake control
faulty – automatic mode activated
" and the
following warning lamps:

and/or fl ashing

- Only the functions for automatic application on switching off the
engine and automatic release on acceleration are available.

- Manual application/release of the electric parking brake and dynamic
emergency braking are unavailable.


6

Display of message " Parking brake faulty
"
and of the following warning lamp:
fl ashing

- Application of the parking brake is not guaranteed.

- The parking brake is temporarily unavailable.
It this situation arises:


)
Wait approximately 3 minutes.

)
After 3 minutes, if the warning lamp is still fl ashing, try to
reinitialise the parking brake, either by pushing and releasing
the control A
while pressing the brake pedal or by means of a
long pull on control lever A
.


7

Battery fault

- Illumination of the battery warning lamp makes it essential to stop the
vehicle as soon as traffi c allows. Stop and immobilise your vehicle.

- Apply the electric parking brake before switching off the engine.

IX!
136
DRIVING





HILL START ASSIST

System which keeps your vehicle
immobilised temporarily (approxi-
mately 2 seconds) when starting on
a gradient, the time to move your
foot from the brake pedal to the ac-
celerator pedal.
This function is only active when:


- the vehicle is completely stationary,
with your foot on the brake pedal,

- in certain conditions on a gradient,

- with the driver’s door closed.
The hill start assist function cannot
be deactivated.

Operation


On an ascending gradient, with
the vehicle stationary, the vehicle
is held for a brief moment when
you release the brake pedal:



- provided you are in fi rst gear or
neutral on a manual gearbox,

- provided you are in D
or M
on an
automatic gearbox.
On a descending gradient, with the
vehicle stationary and reverse gear
engaged, the vehicle is held for a
brief moment when you release the
brake pedal.


Do not exit the vehicle while
it is being held in the hill start
assist phase.
If you need to leave the vehicle with
the engine running, apply the park-
ing brake manually and ensure that
the parking brake warning lamp (in
the instrument panel) is on fi xed
(not fl ashing).

IX
137
DRIVING






5-SPEED MANUAL GEARBOX


Starting the vehicle



)
Check that the gear lever is in
neutral.

)
Do not touch the accelerator.

)
For Diesel engines: turn the
key to position M
and wait until
the pre-heating warning lamp
switches off if it has come on.

)
Operate the starter, turning the
key until the engine starts (no
more than ten seconds).

)
In temperatures lower than 0°C,
declutch while operating the
starter to facilitate starting.



Engaging reverse gear



)
Push the gear lever to the right
then rearwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.









6-SPEED MANUAL
GEARBOX

Engaging reverse gear



)
Raise the ring under the knob
(indicated by the arrow) and
push the gear lever to the left
then forwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
As a safety precaution and to facili-
tate starting of the engine:


- always select neutral,

- press the clutch pedal.

IX!
143
DRIVING











STOP & START

The Stop & Start system puts the en-
gine temporarily into standby - STOP
mode - during stops in the traffi c
(red lights, traffi c jams, or other...).
The engine restarts automatically -
START mode - as soon as you want
to move off. The restart takes place
instantly, quickly and silently.
Perfect for urban use, the Stop &
Start system reduces fuel consump-
tion and exhaust emissions as well
as the noise level when stationary.

Operation



- with the electronic
gearbox

system
, at speeds below 4 mph
(6 km/h), press the brake pedal or
put the gear lever in position N
.
Going into engine STOP mode

The "ECO"
warning lamp comes
on in the instrument panel and
the engine goes into standby:
If your vehicle is fi tted
with the system, a time
counter calculates the
sum of the periods in
STOP mode during a journey. It rests
itself to zero every time the ignition
is switched on with the key.

For your comfort, during parking
maoeuvres, STOP mode is not
available for a few seconds after
coming out of reverse gear.
STOP mode does not affect the func-
tionality of the vehicle, such as for ex-
ample, braking, power steering...

Never refuel with the engine in
STOP mode; you must switch
off the ignition with the key.
Special cases: STOP mode not
available
In this case, the "ECO"

warning lamp fl ashes for a
few seconds then goes off.

This operation is perfectly normal.
STOP mode is not invoked when:


- the driver's door is open,

- the driver's seat belt is not fas-
tened,

- the vehicle has not exceeded
6 mph (10 km/h) since the last
engine start using the key,

- the electric parking brake is ap-
plied or being applied,

- the engine is needed to maintain
a comfortable temperature in the
passenger compartment,

- demisting is active,

- some special conditions (battery
charge, engine temperature,
braking assistance, ambient
temperature...) where the engine
is needed to assure control of a
system.

IX
144
DRIVING


●
gear lever in position A
or M
, re-
lease the brake pedal,

●
or gear lever in position N
and the
brake pedal released, move the
gear lever to position A
or M
,

●
or engage reverse gear.

Going into engine START mode

The "ECO"
warning lamp goes
off and the engine starts with the
electronic
gearbox
system
:


Special cases: START invoked
automatically
In this case the "ECO"

warning lamp fl ashes for a
few seconds, then goes off.

This operation is perfectly normal.

START mode is invoked automati-
cally when:


- the driver's door is open,

- the driver's seat belt is not fas-
tened,

- the speed of the vehicle exceeds
7 mph (11 km/h) with the elec-
tronic gearbox system,

- the electric parking brake is being
applied,

- some special conditions (battery
charge, engine temperature,
braking assistance, ambient tem-
perature...) where the engine is
needed for control of a system. At any time, press the "ECO OFF"

switch to deactivate the system.
This is confi rmed by the switch warn-
ing lamp coming on accompanied by
a message in the screen.
Deactivation


If the system has been deactivated
in STOP mode, the engine restarts
immediately.


The system is reactivated auto-
matically at every new start using
the key.



Reactivation

Press the "ECO OFF"
switch again.
The system is active again; this is
confi rmed by the switch warning
lamp going off and a message in the
screen.

IX
!
!
145
DRIVING
In the event of a fault with the sys-
tem, the "ECO OFF"
switch warning
lamp fl ashes then comes on con-
tinuously.
Have it checked by a CITROËN
dealer or a qualifi ed workshop.
In the event of a fault in STOP mode,
the vehicle may stall. It is then neces-
sary to switch off the ignition and start
the engine again using the key.


Operating fault


The Stop & Start system
makes use of advanced tech-
nology. For any work on the sys-
tem go to a qualifi ed workshop with
the skills and equipment required,
which a CITROËN dealer is able to
provide.

Before doing anything under
the bonnet, deactivate the
Stop & Start system to avoid
any risk of injury resulting from au-
tomatic operation of START mode.


Maintenance

This system requires a battery with
a special specifi cation and techno-
logy (reference numbers available
from CITROËN dealers).
Fitting a battery not listed by
CITROËN introduces the risk of
malfunction of the system.

IX
153
DRIVING
In the event of a steep descent or
under excessive acceleration, the
speed limiter (which does not act
on the brakes) may not be able to
prevent the vehicle from exceeding
the programmed speed.
Use of a fl oor mat other than that
recommended by CITROËN may
affect the normal operation of the
accelerator pedal and hamper the
operation of the speed limiter.
Floor mats approved by CITROËN
are fi tted with a 3rd fi xing located in
the pedal area to avoid any risk of
interference with the pedals.

Suspension/Resumption



)
Press on button 3
.
This action causes the information
"PAUSE"
to appear in zone A
of the
instrument panel.
This action does not cancel the
memorised maximum speed which
remains displayed in zone A
of the
instrument panel.


Overriding the programmed
speed
The accelerator pedal has an end-
of-travel switch. In order to exceed
the memorised maximum speed at
any time, you can press the pedal
all the way down. While the speed
is being exceeded, the speed dis-
played in zone A
will fl ash. You have
only to release the accelerator pedal
to return below the maximum speed,
to restore the function.
The speed will also fl ash if the speed
limiter is not able to prevent the vehi-
cle from exceeding the programmed
speed (e.g. on a steep descent or
under excessive acceleration).
To reactivate the speed limiter, re-
lease the accelerator to slow to a
speed lower than the programmed
speed.


Return to normal driving



)
Either press on button 5
.

)
Or select the speed limiter func-
tion.

)
Or stop the engine.



Operating fault

If there is a fault, a message is
displayed accompanied by an au-
dible signal and illumination of the
SERVICE
warning lamp.
Have it checked by a CITROËN
dealer or a qualifi ed workshop.

IX
!
155
DRIVING

Cruise control must only be
used wh e re the traffi c condi-
tions permit driving at a con-
stant speed .
Do not use it on congested roads
or when the weather or the road
conditions are poor .
The driver must remain attentive
and in complete control of the ve-
hicle .
You are recommended to keep your
feet within range of the pedals .



Overriding the programmed
speed
While cruise control is in operation, it is
always possible to go above the pro-
grammed speed simply by pressing
the accelerator pedal (for example to
overtake another vehicle).
The speed displayed in zone A

fl ashes.
You only have to release the
accelerator pedal to return to the
programmed speed.


Suspension/Resumption



)
Either by pressing the brake
pedal or the clutch pedal.

)
Or by pressing button 3
.

)
Or by the ESP or ASR systems
being active.
For vehicles with a manual gearbox,
cruise control is deactivated if the
gear lever is in neutral.

Reactivation



- By recalling the memorised
speed


After deactivation, press button 3
.
Your vehicle automatically returns
to the memorised cruising speed.
The memorised speed and "ON"

are displayed in zone A
.
If the memorised cruising speed
is higher than the current speed,
the vehicle will accelerate strongly to reach the current speed.

- By selecting the current speed


Press button 1
or 2
once the de-
sired speed has been reached.
The new speed and "ON"
will
appear in zone A
.



Return to normal driving



)
Either press on button 5
.

)
Or select the cruise control func-
tion.

)
Or stop the engine.
The speed that was chosen is no
longer memorised.
"PAUSE"
will be displayed in zone A

of the instrument panel.
These actions do not cancel the
cruising speed which remains dis-
played on the instrument panel.


Operating fault


If there is a fault,
a message is
displayed accompanied by an au-
dible signal and illumination of the
SERVICE
warning lamp.
Have it checked by a CITROËN
dealer or a qualifi ed workshop.

IX
156
DRIVING





LANE DEPARTURE
WARNING SYSTEM
System which detects the involun-
tary crossing of longitudinal traffi c
lane markings on the ground (solid
or broken line).
Sensors, fi tted below the front
bumper, trigger a warning if the vehi-
cle drifts over a lane marking (speed
higher than 50 mph (80 km/h)).
This system is particularly useful on
motorways and main roads.

Activation



)
Press this button, the indicator
lamp comes on.



Deactivation



)
Press this button again, the indi-
cator lamp goes off.
The status of the system remains
in the memory when the ignition is
switched off.


Detection

You are warned by the vibration of
the driver’s seat cushion:


- on the right-hand side, if the
marking on the ground has been
crossed on the right,

- on the left-hand side, if the mark-
ing on the ground has been
crossed on the left.
No warning is transmitted while the
direction indicator is active and for
approximately 20 seconds after the
direction indicator is switched off.
A warning may be transmitted if a direc-
tion marking (e.g. arrow) or non-standard
marking (e.g. graffi ti) is crossed.


Operating fault

In the event of a malfunction, the
service warning lamp comes on, ac-
companied by an audible signal and
a message in the screen.
Contact a CITROËN dealer or a
qualifi ed workshop. The lane departure warning sys-
tem cannot, in any circumstances,
replace the need for vigilance and
responsibility on the part of the
driver.

The detection may be impeded:


- if the sensors are dirty (mud,
snow...),

- if the markings on the ground
are worn,

- if there is little contrast between
the markings on the ground and
the road surface.

IX
157
DRIVING





PARKING SPACE SENSOR

System which measures the parking
space available between two vehi-
cles or obstacles. It measures the
size of the space and gives you in-
formation on:


- the possibility of fi tting into a
free space, depending on the
dimensions of your vehicle and
the distances necessary for your
manoeuvring,

- the level of diffi culty of the ma-
noeuvre to be performed.
The system does not measure spac-
es which are clearly much smaller or
larger than the size of the vehicle.

Displays in the instrument panel

The parking space sensor function
warning lamp can have three different
states:


- off:
the function is not selected,

- on fi xed:
the function is selected
but the conditions for measuring
are not yet met (direction indi-
cator not operating, speed too
high) or the measurement is ter-
minated.

- fl ashing:
measurement is in
progress or the message is be-
ing displayed. You can select the "parking space
sensor" function by pressing but-
ton A.
The fi xed illumination of the
warning lamp indicates that the
function is selected.
During the measurement, the mes-
sage "Measurement in progress -
Vmax 20 km/h (12 mph)" is displayed in the instrument panel screen.