CITROEN DISPATCH SPACETOURER DAG 2021 Handbook (in English)
Page 101 of 324
99
Safety
5Emergency or assistance 
call
 
 
 
 
Localised Emergency Call 
(PE112)
► In an emergency , press button 1 for more 
than 2 seconds.
The lighting of the indicator lamp and a voice 
message confirm that the call has been made to 
the emergency services*.
‘Localised Emergency Call’ immediately locates 
your vehicle and puts you in contact with the 
appropriate emergency services**.
►
 
Pressing again immediately cancels the 
request.
The indicator lamp flashes when the vehicle 
data is sent, and then remains lit when 
communication is established.
* In accordance with  the general conditions of use of the service, available from dealers an\
d subject to technological and technical limitations.
**  In areas covered by ‘Localised Emergency Call’  and ‘Localised Assistance Call’. 
The list of countries covered and telematic services provided is availab\
le from dealers or on the website for your country.
If an impact is detected by the airbag 
control unit, an emergency call is made 
automatically, independently of the 
deployment of any airbags.
‘Localised Emergency Call’ is a service 
that can be accessed free of charge.
System operation
– Upon switching on the ignition, if the indicator 
lamp lights up red, then green, and then goes 
out: the system is operating correctly
.
–
 
If the indicator lamp is fixed red: system 
malfunction
–
 
If the indicator lamp flashes red: replace the 
emergency battery
. 
In the latter two cases, emergency and 
assistance call services may not work.
Contact a dealer or a qualified repairer as soon 
as possible.
The system fault does not prevent the  vehicle from being driven.
Data processing
All processing of personal information 
by the "Localised Emergency Call" system 
(PE112) complies with the framework for 
protection of personal information established 
by Regulation 2016/679 (GDPR) and 
Directive 2002/58/EC of the European 
Parliament and the Council, and in particular, 
seeks to protect the vital interests of the 
data subject, in accordance with Article
  6.1, 
paragraph
  d) of Regulation 2016/679.
Personal information processing is strictly 
limited to the management of the "Localised 
Emergency Call" system used with the “112” 
European single emergency call number.
The "Localised Emergency Call" system is 
able to collect and process only the following 
data relating to the vehicle: chassis number, 
type (passenger vehicle or light commercial 
vehicle), fuel type or power source, most 
recent three locations and direction of travel, 
and a timestamped log file recording the 
automatic activation of the system.
The recipients of the processed data are the 
emergency call handling centres designated 
by the relevant national authorities in the 
territory in which they are located, enabling 
priority reception and handling of calls to the 
“112” emergency number.
Data storage
Data contained in the system’s memory 
is not accessible from outside the system until    
Page 102 of 324
100
Safety
a call is made. The system is not traceable 
and is not continuously monitored in its 
normal operating mode. 
The data in the system's internal memory is 
automatically and continuously erased. Only 
the vehicle’s three most recent locations are 
stored.
When an emergency call is triggered, the data 
log is stored for no more than 13  hours.
Access to data
You have the right to access the data 
and, if necessary, submit a request to 
rectify, erase or restrict the processing of 
any personal information not processed in 
accordance with the provisions of Regulation 
2016/679 (GDPR). Third parties to which data 
has been communicated shall be notified of 
any rectification, erasure or restriction carried 
out in accordance with the aforementioned 
Directive, unless doing so would be 
impossible or require a disproportionate effort. 
You also have the right to lodge a complaint 
with the relevant data protection authority.
* According to the geographic coverage of ‘Localised Emergency Call’, ‘Localised Assistance Call’ and the official national language chosen by the owner 
of the vehicle. 
The list of countries covered and telematic services provided is availab\
le from dealers or on the website for your country
.
Localised Assistance Call
► If the vehicle breaks down, press button 2  
for more than 2 seconds to request assistance 
(confirmed by a voice message*).
►
 
Pressing again immediately cancels the 
request.
Privacy mode allows you to manage the 
level of sharing (data and/or location) 
between your vehicle and CITROËN.
It can be configured in the  Settings menu on 
the touch screen.
By default, depending on equipment, 
deactivate/reactivate geolocation by 
simultaneously pressing the 2 buttons, then 
press the "Localised Assistance Call" button 
to confirm.
If you purchased your vehicle outside the 
CITROËN dealer network, we invite you 
to have a dealer check the configuration of 
these services and, if desired, modify them to 
suit your wishes. In a multilingual country, 
configuration is possible in the official national 
language of your choice.
For technical reasons, in particular to 
improve the quality of telematic services 
for customers, the Manufacturer reserves the 
right to carry out updates to the vehicle's 
on-board telematic system at any time.
If you benefit from the Citroën Connect 
Box offer with the SOS and Assistance 
Pack included, there are additional services 
available to you in your personal space, via 
the website for your country.
For information about the SOS and 
Assistance Pack, please refer to the general 
conditions for these services.
Horn 
 
► Press the central part of the steering wheel.
Pedestrian horn (Electric)
This system alerts pedestrians that the vehicle is  approaching.
The pedestrian horn operates once the vehicle 
is moving and at speeds of up to 19 mph 
(30 km/h), in forward or reverse gear.
This function cannot be deactivated.
Malfunction
In the event of a malfunction, this warning 
lamp comes on on the instrument panel.
Have it checked by a CITROËN dealer or a 
qualified workshop.
Electronic stability control 
(ESC)
The electronic stability control programme  includes the following systems:
–  Anti-lock braking system (ABS) and Electronic 
brake force distribution (EBFD).
–  Emergency braking assistance (EBA).
–  Anti-slip regulation (ASR).
–  Dynamic stability control (DSC).
–  Intelligent traction control.
–  Trailer stability assist (TSA).   
Page 103 of 324
101
Safety
5Pedestrian horn (Electric)
This system alerts pedestrians that the vehicle is approaching.
The pedestrian horn operates once the vehicle 
is moving and at speeds of up to 19 mph 
(30
  km/h), in forward or reverse gear.
This function cannot be deactivated.
Malfunction
In the event of a malfunction, this warning 
lamp comes on on the instrument panel.
Have it checked by a CITROËN dealer or a 
qualified workshop.
Electronic stability control 
(ESC)
The electronic stability control programme  includes the following systems:
–
 
Anti-lock braking system (ABS) and Electronic 
brake force distribution (EBFD).
–
 
Emergency braking assistance (EBA).
–
 
Anti-slip regulation (ASR).
–
 
Dynamic stability control (DSC).
–
 
Intelligent traction control.
–
 
T
 railer stability assist (TSA).
Anti-lock braking system (ABS)/Electronic brake force 
distribution (EBFD)
These systems enhance the vehicle’s stability 
and handling during braking, and enable greater 
control while cornering, particularly on poor or 
slippery road surfaces.
ABS prevents wheel locking in the event of 
emergency braking.
Electronic brake force distribution (EBFD) 
manages overall braking pressure on each 
individual wheel.
►
 
When braking in an emergency
 , depress 
the pedal very firmly and maintain this 
pressure.
The normal operation of the ABS may  result in slight vibrations in the brake 
pedal.
This warning lamp comes on fixed in the  event of an ABS malfunction.
The vehicle retains conventional braking. Drive 
carefully at a moderate speed.
Have it checked by a CITROËN dealer or a 
qualified workshop.
This warning lamp, when lit together with  the STOP and ABS warning lamps, 
accompanied by a message and an audible 
signal, indicates an EBFD malfunction.
You must stop the vehicle.
Stop as soon as it is safe to do so and switch off 
the ignition.
Contact a CITROËN dealer or a qualified 
workshop.
When changing wheels (tyres and rims), 
ensure that these are approved for your 
vehicle.
After an impact
Have it checked by a CITROËN dealer or 
a qualified workshop.
Emergency braking 
assistance (EBA)
In an emergency, this system enables you 
to reach the optimum braking pressure more 
quickly and therefore reduce the stopping 
distance.
It is triggered in relation to the speed at which 
the brake pedal is pressed. This is felt by a 
reduction in the resistance of the pedal and an 
increase in braking efficiency.
Anti-slip regulation (ASR)  / Dynamic stability control 
(DSC)
Anti-slip regulation (or traction control) optimises 
traction by using engine braking and by applying 
the brakes on the driving wheels to avoid one    
Page 104 of 324
102
Safety
or more wheels spinning. It also enhances the 
vehicle's directional stability.
If there is a difference between the vehicle’s 
trajectory and the path desired by the driver, the 
dynamic stability control system automatically 
uses engine braking and the brakes on one or 
more wheels to return the vehicle to the desired 
path, within the limits of the laws of physics.
These systems are activated automatically every 
time the vehicle is started.
These systems are activated in the event of a problem with grip or trajectory 
(confirmed by this warning lamp flashing on the 
instrument panel).
Deactivation/Reactivation
In exceptional conditions (moving a vehicle that 
is bogged down in mud, stuck in snow, on loose 
soil, etc.), it may prove useful to deactivate the 
DSC/ASR systems, so that the wheels can move 
freely and regain grip.
However, it is recommended that the systems be 
reactivated as soon as possible.
Only the ASR system can be deactivated 
from the touch screen.
Deactivating using the button or Advanced 
Grip Control
Press this button or turn the thumbwheel 
to this position.
The indicator lamp in the button or thumbwheel 
comes on: the DSC/ASR systems no longer 
have an effect on engine operation. Deactivating using the touch screen
In the "Driving/Vehicle" menu, deactivate 
the ASR  system.
A confirmation message is displayed and 
this warning lamp on the instrument panel 
comes on.
The ASR system no longer acts on the operation 
of the engine.
Reactivating using the button or Advanced 
Grip Control
Press this button.  
Or
Turn the thumbwheel to this position. 
The indicator lamp in the button or thumbwheel 
goes off.
Reactivating using the touch screen
In the "Driving/Vehicle" menu, activate 
the ASR  system.
A confirmation message is displayed and  this warning lamp on the instrument panel 
goes off.
These systems are reactivated automatically 
every time the ignition is switched off, or at 
speeds over 31 mph (50
  km/h).
Below 31 mph (50
  km/h), these systems must be 
reactivated manually.
Malfunction
In the event of a malfunction, this warning 
lamp comes on on the instrument panel, 
accompanied by the display of a message and 
an audible signal.
Have it checked by a CITROËN dealer or a 
qualified workshop.
ASR/DSC
These systems enhance safety during 
normal driving, but should not encourage 
the driver to take extra risks or drive at high 
speed.
It is in conditions of reduced grip (rain, snow, 
ice) that the risk of loss of grip increases. It 
is therefore important for your safety to keep 
these systems activated in all conditions, and 
particularly in difficult conditions.
Correct operation of these systems depends 
on compliance with the manufacturer's 
recommendations relating to the wheels 
(tyres and rims), braking and electronic 
components, as well as the assembly and 
repair procedures provided by CITROËN 
dealers.
In order to ensure that these systems remain 
effective in wintry conditions, the use of snow 
or all-season tyres is recommended. All four 
wheels must be fitted with tyres approved for 
your vehicle.
All tyre specifications are listed on the 
tyre/paint label. For more information 
on Identification markings , refer to the 
corresponding section.
Intelligent traction control 
("Snow motion")
Depending on version, the vehicle has a system 
to help with driving on snow:  intelligent traction 
control.
This system detects situations of poor surface 
grip that could make it difficult to move off 
or make progress on deep fresh snow or 
compacted snow.
In these situations, the system limits the amount 
of wheel spin to provide the best traction and 
trajectory control for the vehicle.
The use of snow tyres is strongly  recommended on surfaces offering low 
levels of grip.
Trailer stability assist (TSA)
When towing, this system reduces the risk of the 
vehicle or trailer snaking.
Operation
The system is activated automatically when the 
ignition is switched on.
The electronic stability control system (ESC) 
must not have any faults.
The vehicle speed must be between 37 and 99 
mph (60 and 160 km/h).
If the system detects that the trailer is 
snaking, it applies the brakes to stabilise 
the trailer and reduces engine power, if 
necessary, to slow the vehicle (indicated by the    
Page 105 of 324
103
Safety
5Intelligent traction control 
("Snow motion")
Depending on version, the vehicle has a system 
to help with driving on snow: intelligent traction 
control.
This system detects situations of poor surface 
grip that could make it difficult to move off 
or make progress on deep fresh snow or 
compacted snow.
In these situations, the system limits the amount 
of wheel spin to provide the best traction and 
trajectory control for the vehicle.
The use of snow tyres is strongly  recommended on surfaces offering low 
levels of grip.
Trailer stability assist (TSA)
When towing, this system reduces the risk of the 
vehicle or trailer snaking.
Operation
The system is activated automatically when the 
ignition is switched on.
The electronic stability control system (ESC) 
must not have any faults.
The vehicle speed must be between 37 and 99 
mph (60 and 160
  km/h).
If the system detects that the trailer is 
snaking, it applies the brakes to stabilise 
the trailer and reduces engine power, if 
necessary, to slow the vehicle (indicated by the 
flashing of this warning lamp on the instrument 
panel and the brake lamps coming on).
For information on weights and towed loads, 
refer to the Engine technical data and towed 
loads section or your vehicle’s registration 
certificate.
To ensure safe driving with a  Towing device, 
refer to the corresponding section.
Malfunction
If a fault occurs, this warning lamp lights 
up on the instrument panel, accompanied 
by a message and an audible signal.
To continue towing a trailer, reduce speed and 
drive carefully!
Have it checked by a CITROËN dealer or a 
qualified workshop.
The trailer stability control system  provides an extra safety feature under 
normal driving conditions, when following the 
recommendations for use of trailers and 
current legislation in force in your country. It 
must not encourage the driver to take extra 
risks, such as using a trailer in unsuitable 
conditions of operation (e.g.
  excessive load, 
exceeded nose weight, worn or under-inflated 
tyres, faulty braking system) or driving at 
excessive speed.
In certain cases, the system may not detect 
trailer snaking, particularly with a light trailer.
When driving on slippery or poor surfaces, the 
system may not be able to prevent sudden 
trailer snaking.
Advanced Grip Control
(Depending on version)
A special, patented traction control system, 
which improves driveability on snow, mud and 
sand.
This system, optimised for operation in a range 
of conditions, enables you to manoeuvre in most 
slippery conditions (encountered during normal 
passenger car use).
When combined with all-season Peak Mountain 
Snow Flake tyres, this system offers a 
compromise between safety, grip and driveability.
The accelerator pedal should be pressed 
sufficiently to allow the system to harness the 
power of the engine. Operation at high engine 
speeds is completely normal.
A five-position selector knob allows you to 
choose the setting best suited to the driving 
conditions encountered.
An indicator lamp associated with each mode 
comes on, accompanied by the display of a 
message to confirm your choice.  
Page 106 of 324
104
Safety
Operating modes 
 
 
 
Standard (ESC)
This mode is calibrated for a low level of  wheel spin, based on the different levels 
of grip normally encountered on the road.
Whenever the ignition is switched off, the 
system automatically resets to this mode.
Snow
This mode adapts its strategy to the  conditions of grip encountered for each of 
the two front wheels on moving off.
(mode active up to 50 mph (80
  km/h))
All terrain (mud, damp grass, etc.)
This mode, when moving off, allows considerable spin on the wheel with the 
least grip to optimise clearing of the mud and to 
regain grip. At the same time, the wheel with the 
most grip is controlled in such a way as to 
transmit as much torque as possible.
When moving, the system optimises wheel spin 
to respond to the driver's requirements as fully 
as possible.
(mode active up to 31 mph (50
  km/h))
Sand
This mode allows little spin on the two driving wheels at the same time to allow 
the vehicle to move forward and limit the risks of 
getting stuck in the sand.
(mode active up to 75 mph (120
  km/h))
Do not use the other modes on sand as 
the vehicle may become stuck.
You can deactivate the ASR and DSC systems by turning the knob to the "OFF" 
position.
The ASR and DSC systems will no  longer act on the operation of the engine 
or of the brakes in the event of a change of 
trajectory.
These systems are reactivated automatically 
from 31 mph (50
  km/h) and whenever the 
ignition is switched on.
Recommendations
Your vehicle is designed principally to 
drive on tarmac roads but it allows you to 
occasionally drive on other less passable 
terrain.
However, it does not permit off-road driving 
such as:
–
 
crossing and driving on terrain which 
could damage the underbody or strip away 
components (fuel pipe, fuel cooler
, etc.) due 
to obstacles or stones in particular,
–
 
driving on terrain with steep gradients and 
poor grip,
–
 
crossing a stream.
Seat belts
Inertia reel
The seat belts are equipped with an inertia reel 
which allows the strap length to automatically 
adjust to your shape. The seat belt returns to its 
storage automatically when it is not used.
The inertia reels are fitted with a device which 
automatically locks the strap in the event of a 
collision, emergency braking or if the vehicle rolls 
over. It can be released by pulling the strap firmly 
and then releasing it so that it reels in slightly.
Pyrotechnic pretensioning
This system improves safety in the event of a 
frontal or side impact.
Depending on the severity of the impact, the 
pyrotechnic pretensioning system instantly 
tightens the seat belts against the body of the 
occupants.
The pyrotechnic pretensioning seat belts are 
enabled when the ignition is on.
Force limiter
This system reduces the pressure of the seat 
belt on the chest of the occupant, thus improving 
their protection.
In the event of an impact
Depending on the nature and 
seriousness of the impacts, the pyrotechnic 
device may trigger before and independently 
of airbag deployment. Deployment of the 
pretensioners is accompanied by a slight 
discharge of harmless smoke and a noise, 
due to the activation of the pyrotechnic 
cartridge incorporated in the system.
In all cases, the airbag warning lamp comes 
on.
Following an impact, have the seat belt 
system checked, and if necessary replaced, 
by a CITROËN dealer or a qualified 
workshop.  
Page 107 of 324
105
Safety
5The pyrotechnic pretensioning seat belts are 
enabled when the ignition is on.
Force limiter
This system reduces the pressure of the seat 
belt on the chest of the occupant, thus improving 
their protection.
In the event of an impact
Depending on the nature and 
seriousness of the impacts, the pyrotechnic 
device may trigger before and independently 
of airbag deployment. Deployment of the 
pretensioners is accompanied by a slight 
discharge of harmless smoke and a noise, 
due to the activation of the pyrotechnic 
cartridge incorporated in the system.
In all cases, the airbag warning lamp comes 
on.
Following an impact, have the seat belt 
system checked, and if necessary replaced, 
by a CITROËN dealer or a qualified 
workshop.
Front seat belts 
 
The front seat belts are fitted with a pyrotechnic 
pretensioning system and a force limiting 
system.
This system improves safety in the front seats in 
the event of a front or side impact. 
Depending on the severity of the impact, the 
pyrotechnic pretensioning system instantly 
tightens the seat belts against the body of the 
occupants.
The pyrotechnic pretensioning seat belts are 
enabled when the ignition is on. The force limiting system reduces the pressure 
of the seat belt on the chest of the occupant, 
thus improving their protection.
Locking 
 
► Pull the strap then insert the tongue in the 
buckle.
►
 
Check that the seat belt is fastened correctly 
by pulling the strap.
Unfastening
► Press the red button on the buckle.
►  Guide the seat belt as it reels in.  
Page 108 of 324
106
Safety
Height adjustment 
 
► To lower the attachment point, while moving 
control A downwards, slide the assembly down 
to the desired position.
► 
T
 o raise the attachment point, slide the 
assembly up to the desired position.
The upper part of the diagonal strap  should lie across the shoulder.
2-seat front bench seat 
 
If your vehicle is fitted with a front bench seat, 
ensure that each belt is used with its correct 
buckle.
Do not interchange the driver's seat belt or 
buckle with the centre seat belt or buckle.
Rear seat belts 
 
 
 
A 3-seat bench seat (one-piece or split 1/3 seat 
- 2/3 bench seat) is fitted with three-point seat 
belts and inertia reels on the outer seats.
The centre seat has a seat belt guide and inertia 
reel fitted into the seat backrest.
The seat belt inertia reels for the outer seats in 
row 2 are fitted with force limiters.
The seats in row 3 have three-point seat belts 
with inertia reels.
For rows 2 and 3, connect each seat belt 
to its correct buckle.
Do not interchange the belts or buckles for 
the outer seats with the belt or buckle for the 
centre seat.
When folding the side seats or placing the 
backrests in the table position, avoid trapping 
the belt for the centre seat.
After folding or moving a rear seat or bench 
seat, ensure that the seat belt has reeled 
in correctly and that the buckle is ready to 
receive the belt tongue.
When removing/repositioning the outer seats 
or when accessing row 3, avoid trapping the 
centre belt.
With individual seats
Shine, Business Lounge
 
 
They are fitted with three-point seat belts 
with guides and belt inertia reels built into the 
backrests.
Seat belt(s) warning lamps
A. Front seat belts not fastened/unfastened 
warning lamp.
B. Left-hand seat belt not fastened/unfastened 
warning lamp.
C. Centre seat belt unfastened warning lamp (if 
your vehicle is fitted with a 2-seat front bench 
seat).
D. Right-hand seat belt not fastened/unfastened 
warning lamp (if your vehicle is fitted with 
individual front seats).
Right-hand seat belt unfastened warning 
lamp (if your vehicle is fitted with a 2-seat 
front bench seat).
On switching on the ignition, the warning lamp(s) 
come(s) on if the corresponding seat belt is not 
fastened or is unfastened.
At speeds above approximately 12 mph 
(20 km/h), the warning lamp(s) flash(es) for 2 
minutes, accompanied by an audible signal. 
Once these 2 minutes have elapsed, the warning 
lamp(s) remain(s) on until the driver or the 
passenger fastens their seat belt.  
Page 109 of 324
107
Safety
5Seat belt(s) warning lamps
A.Front seat belts not fastened/unfastened 
warning lamp.
B. Left-hand seat belt not fastened/unfastened 
warning lamp.
C. Centre seat belt unfastened warning lamp (if 
your vehicle is fitted with a 2-seat front bench 
seat).
D. Right-hand seat belt not fastened/unfastened 
warning lamp (if your vehicle is fitted with 
individual front seats).
Right-hand seat belt unfastened warning 
lamp (if your vehicle is fitted with a 2-seat 
front bench seat).
On switching on the ignition, the warning lamp(s) 
come(s) on if the corresponding seat belt is not 
fastened or is unfastened.
At speeds above approximately 12 mph 
(20
  km/h), the warning lamp(s) flash(es) for 2 
minutes, accompanied by an audible signal. 
Once these 2 minutes have elapsed, the warning 
lamp(s) remain(s) on until the driver or the 
passenger fastens their seat belt.
Advice
The driver must ensure that passengers  use the seat belts correctly and that they 
are all fastened before setting off.
Wherever seated in the vehicle, you must 
always fasten the seat belt, even for short 
journeys.
Do not invert the seat belt buckles, as they 
will not fulfil their role properly.
To ensure the proper functioning of the belt 
buckles, make sure that there are no foreign 
bodies present (e.g.
  a coin) before fastening.
Before and after use, ensure that the seat belt 
is reeled in correctly.
After folding or moving a seat or rear bench 
seat, ensure that the seat belt is positioned 
and reeled in correctly.
Installation
The lower part of the strap must be 
positioned as low as possible over the pelvis.
The upper part must be positioned in the 
hollow of the shoulder.
In order to be effective, a seat belt must:
–
 
be tightened as close to the body as 
possible.
–
 
be pulled in front of you with a smooth 
movement, ensuring that it is not twisted.
–
 
only be used to secure one person.
–
 
not show signs of tearing or fraying.
–
 
not be changed or modified, in order to 
avoid affecting its performance.
Recommendations for children
Use a suitable child seat if the passenger 
is less than 12 years old or shorter than 1.5 
metres.
Never use the same seat belt to secure more 
than one child.
Never carry a child on your lap.
For more information on  Child seats, refer to 
the corresponding section.
Maintenance
In accordance with current safety 
regulations, for all work on your vehicle's 
seat belts, contact a qualified workshop with 
the skills and equipment needed, which a 
CITROËN dealer is able to provide.
Have the seat belts checked regularly by a 
CITROËN dealer or a qualified workshop, 
particularly if the straps show signs of 
damage.
Clean the seat belt straps with soapy water or 
a textile cleaning product, sold by CITROËN 
dealers.
Airbags
General information
System designed to help improve the safety 
of the occupants sitting in the front seats and 
the rear outer seats, in the event of a violent 
collision. The airbags supplement the action   
Page 110 of 324
108
Safety
of the seat belts equipped with a force limiting 
system.
Electronic detectors record and analyse the 
front and side impacts sustained in the impact 
detection zones:
– 
In the event of violent impact, the airbags 
deploy instantly and help better protect the 
occupants of the vehicle; immediately after the 
impact, the airbags deflate rapidly in order not 
to hinder the visibility or the possible exit of the 
occupants.
–
 
In the event of a slight impact, a rear impact 
and under certain rollover conditions, the airbags 
may not deploy; only the seat belt helps to 
protect you in these situations.
The seriousness of the impact depends on the 
nature of the obstacle and the speed of the 
vehicle at the moment of collision.
The airbags do not operate when the 
ignition is switched off.
This equipment will only deploy once. If a 
second impact occurs (during the same or a 
subsequent accident), the airbag will not be 
deployed again.
Impact detection zones
A. Front impact zone
B. Side impact zone
When one or more airbags are deployed, 
the detonation of the pyrotechnic charge 
incorporated in the system makes a noise and 
releases a small quantity of smoke.
This smoke is not harmful, but sensitive 
individuals may experience slight irritation.
The detonation noise associated with the 
deployment of one or more airbags may result 
in a slight loss of hearing for a short time.
Front airbags 
 
System that protects the driver and front 
passenger in the event of a serious front impact, 
limiting the risk of head and chest injury.
The driver's airbag is fitted in the centre of the 
steering wheel; the front passenger airbag is 
fitted in the dashboard above the glove box.
Deployment
The airbags are deployed, except the front 
passenger airbag if it is deactivated, in the 
event of a serious front impact to all or part of 
the frontal impact zone A, in the longitudinal 
centreline of the vehicle on a horizontal plane 
and directed from the front to the rear of the 
vehicle.
The front airbag inflates between the thorax 
and head of the front occupant of the vehicle 
and the steering wheel, driver's side, and the 
dashboard, passenger side to cushion their 
forward movement.
 
 
When driving , keep the glove box 
closed. Otherwise, this could cause injury 
in the event of an accident or sudden braking.
Lateral airbags