change wheel CITROEN DS3 2009 Owners Manual

)
Turn t
hum
b wheel 1to the
"LIMIT"
position: the speed limiter mode is
selected but is not switched on (PAUSE).
You do not have to switch the speed limiter on
in order to set the speed. ) Set the speed value b
y pressin
g button
2
or 3(e.g.: 55 mph (90 km/h)).
Pro
grammin
g
You can then change the programmed speed using buttons
2 and
3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph
(km/h
) = maintained press.
)
Switch the speed limiter on b
y pressin
g button
4.
)
Switch the speed limiter o
ff by pressin
g button
4: the display
confirms that it has been switched o
ff (PAU
SE).
)
Switch the speed limiter back on by pressing button 4 aga
in.
Excee
di
ng t
he programme
d spee
d
Press
ing t
he acce
lerator pe
dal to excee
d the programme
d spee
d will not
have
any effect unless you press the pedal
firmly
past the y
point of resistance .
The speed limiter is deactivated temporarily and the programmed speed,
which is still displayed, flashes. Returning to the programmed speed, by means of intentional or unintentional deceleration of the vehicle, automatically cancels the flashin
g of the pro
grammed speed.
On a stee
p descent or in the event o
f
sharp acce
lerat
ion, t
he s
peed limiter
will
not
be a
ble to
prevent t
he ve
hicle
from exceeding the programmed speed. To avoid any risk of jamming of the pedals: - ensure that the mat is positioned
correctl
y,
- do not
fit one mat on to
p of another.
Leavin
g limiter mode
)
Turn th
umb wh
eel 1 to the "0" position:
t
he s
peed limiter mo
de is dese
lecte
d. The
display returns to t
he distance recor
der.
Operating
fault
In the event of a speed limiter malfunction, the speed is cleared resulting in flashing of thedas
hes.
Have the s
ystem checked b
y a CITROËN
deale
r.

Pro
grammin
g
)
Turn thumb wheel
1 to the
"CR
UISE"
position: the cruise control mode is selected but is not switched on (PAUSE).
)
Set the programmed speed by acceleratin
g to the required speed, then
press button
2or 3
(e.g.: 70 mph
(11 0 k m
/h)).
You can then change the programmed speed using buttons
2 and 3 :
- b
y + or - 1 mph
(km/h
) = short press,
- b
y + or - 5 mph
(km
/h) = lon
g press,
- in steps o
f + or - 5 mph
(km
/h) = maintained press.
)
Switch o
ff the cruise control b
y pressin
g button
4 : the display
confirms that it has been switched o
ff (PAU
SE).
)
Switch the cruise control back on b
y pressin
g button
4again.
Excee
di
ng t
he programme
d spee
d
Intentional or unintentional exceeding of the programmed speed results in flashing of this speed on the display. Return to the programmed speed, by means of intentional or unintentional deceleration of the vehicle, automatically cancels the flashing of the speed. Leaving cruise control mode )
Turn t
hum
b wheel 1 to t
he "
0"position: the cruise control mode is
deselected. The display returns to the distance recorder.
Operatin
g fault
In the event of a cruise control malfunction
,
the speed is cleared resultin
g in
flashin
g of the
dashes. Have it checked b
y a CITRO
ËN dealer.
Wh
en t
he cru
ise contro
l is sw
itched on,
be care
ful if you maintain the pressure
on one o
f the programmed speed
changing buttons: this may result in a very rapid change in the speed of your vehicle.
Do not use
the cruise control on
slipper
y roads or in heav
y tra
ffic.
On a stee
p descent, the cruise control
will
not
be a
ble to
prevent t
he ve
hicle
from exceeding the programmed speed. To avoid any risk o
f jamming o
f the
pedals: - ensure that the mat is positioned
correctly,
- never fit one mat on top of another.

Practical information
Removing the wheel

Parking the vehicle
Imm
obilise the vehicle wh
ere it does

not block traffic: the ground must belevel, stable and not slipper
y.
Appl
y the parkin
g brake, switch o
ff the
ignition and en
gage first
gear
* to lock
the w
heels.
If necessary, place a chock under thewheel diagona
lly oppos
ite t
he w
heel to
be changed.
It is imperative that you ensure that the occupants get out of the vehicle andwait where the
y are safe.
Never
go un
derneat
h a ve
hicle ra
ised
using a jack; use an axle stand.
List of o
perations
)
Remove the chromed bolt cover from eac
h
o
f the bolts usin
g the tool
3(allo
y wheels
only).
)
Fit the socket
4 on t
he w
heelbrace
1
to
slacken the security bolt.
)
Slacken the other bolts using the wheelbrace
1 only.
* position
P for an automatic
gearbox.