Citroen DS3 2014 1.G Owner's Manual

04
299
DS3_en_Chap13b_RT6-2-8_ed01-2014
Male voice / Female voicePress SETUP to display the
configuration
  menu.
Select "Select male voice" or "Select
female voice"
  then   confirm   "Ye s" to
activate
  a   male   or   female   voice.  
The
 
system

  restarts.
Select "Voice synthesis"
  and   confirm.
NAVIGATION - GUIdANcE

05
DS3_en_Chap13b_RT6-2-8_ed01-2014
Access to the "TRAFFIc INFORMATION " menu
List of TMC  messages   in   order  of
  distance   from   the   vehicle.
Go
  from   the   list   to   the   menu   (left/right).
"Traffic information"
"Geographic filter "
"Select TM c station"
(automatic,
  manual)
"
d isplay/ d o not display
messages "
or
Press "TRAFFI
c
".
TRAFFIc INFORMATION

05
301
DS3_en_Chap13b_RT6-2-8_ed01-2014
configure the filtering and display of TMc messages
TMC (Traffic Message Channel) messages with GPS Navigation provide traffic information in real time.
Press the TRAFFI c button to display the
"Traffic information"
  menu.
Select the "Geographic filter" function
and
  confirm. The
  system   offers   a   choice   of:
-
"Retain all the messages",
or
-
"Retain the messages"
●
 
"
Around the vehicle",
  (confirm  
the

  mileage   to   modify   and   select  
the distance),
●

 
"
On the route".
Confirm
  "OK"   to   save   the   modifications.
We
  recommend:
-
 
a
  filter   on   the   route   and
-
 
a
  filter   around   the   vehicle   of:
-
 
12
  miles   (20   km)   in   urban   areas,
-
 
30
  miles   (50   km)   on   motorways.
TRAFFIc INFORMATION

05
DS3_en_Chap13b_RT6-2-8_ed01-2014
Principal TMc symbols
Red and yellow triangle: traffic information, for example:
Black   and   blue   triangle:   general   information,   for   example:
Weather reports
Modified
  signage
Risk
  of   explosion Traffic
  reports
Narrow   carriageway
Road closed
Wind
Slippery surface
Demonstration Fog
a

ccident
Danger
Parking
Delay
No entry Snow
  /   ice
Roadworks
Traffic
  jam
Receiving TA messages
The TA (Traffic  Announcement)   function   gives   priority   to  T A  alert  messages.
 T o   operate,   this   function   needs   good   reception   of   a  
radio

  station   transmitting   this   type   of   message.   When   a   traffic   report  
is

  transmitted,   the   current   audio   source   (Radio,   CD,   USB,   ...)   is  
interrupted

  automatically   to   play   the  
T
A
 
message.   Normal   playback  
of

  the   audio   source   resumes   at   the   end   of   the   transmission   of   the  
message.Press

RA d IO   to   display   the   menu.
Select "Service announcements" then
confirm.
a

ctivate or deactivate "TA "
  then   confirm.
The
  volume   setting   for  
T
A
 
messages   can   be   adjusted   only   during   the  
transmission

  of   this   type   of   alert.
Activate
  or   deactivate   the   function   at   any   time   by   pressing  
the

  button.
During
  a   message,   press   the   button   to   interrupt   it.
TRAFFIc INFORMATION

06
303
DS3_en_Chap13b_RT6-2-8_ed01-2014
Access to the "TELEPHONE" menu
"Telephone"" d ial"
"
d irectory of contacts"
"
c ontacts management "
"Phone functions "
"Bluetooth functions "
"Hang up "
Go
  from   the   list   to   the   menu   (left/right).
or
List of recent calls sent and
received with the telephone
connected
 
to
 
the
 
system.
Press
 
this
 
button.
To
 
make
 
a
 
call,
 
select
 
a
 
number
 
in
 
the
 
list
 
and
 
confirm
 
" OK"
to
 
start
 
the
 
call.
Connecting
 
a
 
different
 
telephone
 
deletes
 
the
 
list
 
of
 
recent

 
calls. No
  telephone   connected.
Telephone
  connected.
Incoming
  call.
Outgoing
  call.
Synchronisation of
contacts
  in   progress.
Telephone call in
progress.
In the top bar of the permanent
display
USING THE TELEPHONE

06
DS3_en_Chap13b_RT6-2-8_ed01-2014
USING THE TELEPHONE
Pairing a Bluetooth telephone
First connectionFor reasons of safety and because they require prolonged attention on  the   part   of   the   driver,   the   operations   for   pairing   the   Bluetooth  
mobile

  telephone   to   the   hands-free   system   of   the   audio   unit   must   be  
carried out with the vehicle stationary

.
In
 
the
 
Bluetooth
 
menu
 
of
 
your
 
telephone,
 
select
 
the
 
name

 
"C
ITR
o
ËN
"
 
from
 
the
 
list
 
of
 
devices
 
detected. Press
  this   button.
Select "Bluetooth functions " and
confirm.
Select "Peripherals search " and
confirm.
The list of peripheral devices detected
is
  displayed.   Wait   until   the   " c onnect"
button
  is   available.
You
 
can
 
check
 
the
 
compatibility
 
of
 
your
 
telephone
 

at

 
www.citroen.co.uk
 
(services).
a

ctivate the telephone's b luetooth function
and ensure that it is "visible to all" (telephone
configuration).
Quick procedure from the telephone
Enter
 
a
 
minimum
 
4
 
figure
 
code
 
in
 
the
 
telephone
 
and
 
confirm. Enter

 
the
 
same
 
code
 
in
 
the
 
system,
 
select "

OK"
 
and
 
confirm. Procedure from the system

06
305
DS3_en_Chap13b_RT6-2-8_ed01-2014
USING THE TELEPHONE
Select "connect" and confirm.
The   system   offers   to   connect   the  
telephone:
-


in "
Hands-free mode" (telephone
only),
-

in "
Audio"   mode   (streaming:   playing  
music

  files   on   the   telephone),
-

or "
All" (for selection of both
modes).
Select "OK"
  and   confirm. Then
  accept   automatic   connection   on   the   telephone   to   allow   the  
telephone

  to   reconnect   automatically   every   time   the   vehicle   is  
started.
The

 
ability   of   the   system   to   connect   in   only   one   mode   depends   on  
the

 
telephone.  
The
  two   modes   may   both   connect   by   default.
The "Hands-free mode" should be used in preference if
"Streaming"
  is   not   desired.
The
 
services   available   depend   on   the   network,   the   SIM   card   and   the   compatibility   of   the   Bluetooth   telephone   used.   Check   the   telephone  
manual

 
and   with   your   network   provider   for   details   of   the   services   available   to   you.
Depending   on   the   type   of   telephone,   the   system   will   ask   you   to  
accept

  or   not   the   transfer   of   your   contacts.
o

n return to the vehicle,the last telephone connected
automatically
  reconnects,   within   around   30   seconds   after  
switching

  on   the   ignition   (Bluetooth   activated   and   visible).
To
  modify   the   automatic   connection   mode,   remove   the   pairing  
and

  pair   the   telephone   again   with   the   desired   mode.
Enter
  a   minimum   4   figure   code   in   the   telephone  
and

  confirm.
Enter   the   same   code   in   the   system,  
select "

OK"   and   confirm.
Select
  the   name   of   the   desired  
peripheral

  from   the   list   of   devices  
detected

  then   confirm

06
DS3_en_Chap13b_RT6-2-8_ed01-2014
USING THE TELEPHONE
directory configuration / Synchronisation with the telephone
Press PHONE then select "contacts
management "   and   confirm.
Select "New contact" to enter a new
contact.
Select "Sort by Name/First name" or
"Sort by First name/Name" to choose
the
  order   in   which   they   appear.
Select "
d elete all contacts" to delete
the
  contacts   saved   in   the   system. Select "Synchronization options
":
-
 
No
  synchronization:   only   the  
contacts

  saved   in   the   system  
(always

  present).
-
 
Display
  telephone   contacts:   only   the  
contacts

  saved   in   the   telephone.
-
 
Display
  SIM   card   contacts:   only   the  
contacts

  saved   on   the   SIM   card.
-
 
Display
  all   phone   contacts:  
contacts on the SIM card and in the
telephone.
Select "

Import all the entries"   to   import  all the contacts in the telephone and
save
  them   in   the   system.
Once
  imported,   a   contact   remains   visible  
whatever

  telephone   is   connected.
Select "
c ontact mem. status" to see the
number
  of   contacts   saved   in   the   system  
or

  imported,   and   the   free   memory.

06
307
DS3_en_Chap13b_RT6-2-8_ed01-2014
Editing, importing or deleting a contact
Press PHONE then select "directory of
contacts "   and   confirm.
Select "Search",
  then   turn   the   knob   to  
choose

  in   numerical   or   alphabetical   order  
a

  group   of   contacts   from   the   entries   made  
previously

,   then   confirm.
Go to the list of contacts, select the
desired
  contact   then   confirm.
Select "Open" to view a contact on the
telephone
  or   modify   a   contact   saved   in  
the

  system.
Select "Import"
  to   copy   a   contact   from  
the

  telephone   to   the   system.
Select "
d elete" to delete a contact
recorded
  in   the   system.
USING THE TELEPHONE
Select OK or press the back button to exit this  menu.
Once
 
the
 
contact   has   been   imported,   the   Bluetooth   symbol  
disappears,

  replaced   by   the   telephone   symbol   which   shows   that   the  
contact

 
has   been   saved   in   the   system.
It
 
is
 
not
 
possible   to   modify   or   delete   contacts   in   the   telephone   or   the  
SIM

 
card
 
via   the   Bluetooth   connection.
In the "
d
irectory of contacts"   menu,   the   import   and   deletion   of  
contacts

 
is
  done   one   by   one.

06
DS3_en_Chap13b_RT6-2-8_ed01-2014
USING THE TELEPHONE
Press PHONE twice.
Select " d ial"   then   confirm. Select "
d irectory of contacts" then
confirm.
Dial
  the   telephone   number   using   the  
virtual

  keypad   selecting   each   number  
in

  turn.
Confirm
  "OK"   to   make   the   call. Press TEL or twice on PHONE.
c

alling a new number
c
alling a contact
Select   the   desired   contact   and   confirm.
If access was via the PHONE button,
select "
c all"   and   confirm.
Select
  the   number   and   confirm   to   start  
the

  call.
Making a callUse of the telephone is not recommended while driving. We recommended  that   you   park   safely   or   make   use   of   the   steering  
mounted

  controls.