turn signal Citroen DS4 2010.5 1.G Owner's Manual

Warning lampis onCauseAction/Obser vations
Left-hand
direction indicator
flashing with buzzer. The lighting stalk is pushed down.
Right-hand direction indicator flashing with buzzer. The lighting stalk is pushed up.
Sidelamps fixed. The lighting stalk is in the "Sidelamps" position.
Dipped beam headlamps fixed. The lighting stalk is in the "Dipped beam headlamps" position.
Main beam headlamps fixed. The lighting stalk is pulled towards you. Pull the stalk to return to dipped beam headlamps.
Front foglamps fixed. The front foglamps are switched on. Turn the ring on the stalk rear wards twice to switch off the front foglamps.
Rear foglamps fixed. The rear foglamps are switched on. Turn the ring on the stalk rear wards to switch off the rear foglamps.
Hazard warning lamps flashing with audible signal. The hazard warning lamps switch, located on the dashboard, has been operated.
The left-hand and right-hand direction indicators a nd their associated indicator lamps flash simultaneously.
Operation indicator lamps
If one of the following indicator lamps comes on, this confirms that the corresponding system has come into o peration. It may be accompanied by an audible signal and a message on the multifunction screen.

In the event of a malfunction with the remote control, you can no longer unlock, lock or locate your vehicle.  First of all, use the key in the lock to unlock or lock your vehicle.  Then, reinitialise the remote control. If the problem persists, contact a CITROËN dealer as soon as possible.
Fault with the remote
control
Reinitialisation
 Switch off the ignition and remove the
ignition key.  Press the closed padlock immediately for a few seconds.  Turn the key to position 2 (Ignition on) .  Switch off the ignition and remove the key from the ignition switch. The remote control is fully operational again.
Changing the battery
Battery ref.: CR2032/3 volts.  Unclip the cover using a small screwdriver at the two cutouts.  Lift off the cover.  Remove the flat battery from its location.  Fit the new battery into its location obser ving the original direction of fitment.  Clip the cover onto the casing.
If the battery is flat, you are informed by illumination of this warning lamp, an audible signal and a message in the screen.

125Visibility
Switching off the lighting when switching off the ignition
When the ignition is switched off, all of the lamps switch off immediately, except for the dipped beam headlamps if automatic guide-me-home lighting is activated.
Temporarily keeping the dipped beam headlamps on after the vehicle's ignition has been switched off makes the driver's exit easier when the light is poor.
Switching on
 With the ignition off, "flash" the headlamps using the lighting stalk.  A fur ther "headlamp flash" switches the function off.
Switching off
The manual guide-me-home lighting switches off automatically after a set time.
Manual guide-me-home
lighting
Daytime lighting, compulsory in cer tain countries, which comes on automatically when the engine is star ted making the vehicle more visible to other users.
This function is assured:
- in countries where it is imposed by regulations, by illumination of the dipped beam headlamps associated with illumination of the sidelamps and number plate lamps. - for other countries where it is provided, by illumination of dedicated lamps associated with illumination of the sidelamps and number plate lamps.
The instruments and controls (multifunction screen, air conditioning control panel, ...) are not illuminated, except in night mode with manual or automatic illumination of headlamps.
Daytime running lamps
This function can be activated or deactivated via the vehicle configuration menu.
Switching on the lighting when switching on the ignition
To reactivate the lighting control stalk, turn the ring A to position A"0" - lighting off, then to the position of your choice. If the lighting is switched on manually after
switching off the ignition, there is an audible signal when a front door is opened to warn the driver that they have forgotten to switch off the vehicle's lighting, with the ignition off. They switch off automatically after a period which depends on the state of charge of the battery (entry to energy economy mode).

The sidelamps and dipped beam headlamps are switched on automatically, without any action on the par t of the driver, when a low level
of external light is detected or in cer tain cases of activation of the windscreen wipers. As soon as the brightness returns to a sufficient level or after the windscreen wipers are switched off, the lamps are switched off automatically.
Automatic illumination of headlamps
Activation
 Turn the ring to the "AUTO" position. The automatic illumination of headlamps is accompanied by a message in the screen.
Deactivation
 Turn the ring to another position. Deactivation is accompanied by a message in the screen.
Associated with the automatic "Guide-me-home" lighting
Association with the automatic lighting provides the "guide-me-home" lighting with the following additional options: - selection of the lighting duration of 15, 30 or 60 seconds in the vehicle parameters
in the vehicle configuration menu, - automatic activation of "guide-me-home" lighting when automatic lillumination of headlamps is in operation.
Parking lamps
Side markers for the vehicle by illumination of the sidelamps on the traffic side only.  Within one minute of switching off the
ignition, operate the lighting control stalk up or down depending on the traffic side (for example: when parking on the left; lighting control stalk upwards; the right hand sidelamps are on). This is confirmed by an audible signal and illumination of the corresponding direction indicator warning lamp in the instrument panel. To switch off the parking lamps, return the lighting control stalk to the central position.

125Visibility
Switching off the lighting when switching off the ignition
When the ignition is switched off, all of the lamps switch off immediately, except for the dipped beam headlamps if automatic guide-me-home lighting is activated.
Temporarily keeping the dipped beam headlamps on after the vehicle's ignition has been switched off makes the driver's exit easier when the light is poor.
Switching on
 With the ignition off, "flash" the headlamps using the lighting stalk.  A fur ther "headlamp flash" switches the function off.
Switching off
The manual guide-me-home lighting switches off automatically after a set time.
Manual guide-me-home
lighting
Daytime lighting, compulsory in cer tain countries, which comes on automatically when the engine is star ted making the vehicle more visible to other users.
This function is assured:
- in countries where it is imposed by regulations, by illumination of the dipped beam headlamps associated with illumination of the sidelamps and number plate lamps. - for other countries where it is provided, by illumination of dedicated lamps associated with illumination of the sidelamps and number plate lamps.
The instruments and controls (multifunction screen, air conditioning control panel, ...) are not illuminated, except in night mode with manual or automatic illumination of headlamps.
Daytime running lamps
This function can be activated or deactivated via the vehicle configuration menu.
Switching on the lighting when switching on the ignition
To reactivate the lighting control stalk, turn the ring A to position A"0" - lighting off, then to the position of your choice. If the lighting is switched on manually after
switching off the ignition, there is an audible signal when a front door is opened to warn the driver that they have forgotten to switch off the vehicle's lighting, with the ignition off. They switch off automatically after a period which depends on the state of charge of the battery (entry to energy economy mode).

The sidelamps and dipped beam headlamps are switched on automatically, without any action on the par t of the driver, when a low level
of external light is detected or in cer tain cases of activation of the windscreen wipers. As soon as the brightness returns to a sufficient level or after the windscreen wipers are switched off, the lamps are switched off automatically.
Automatic illumination of headlamps
Activation
 Turn the ring to the "AUTO" position. The automatic illumination of headlamps is accompanied by a message in the screen.
Deactivation
 Turn the ring to another position. Deactivation is accompanied by a message in the screen.
Associated with the automatic "Guide-me-home" lighting
Association with the automatic lighting provides the "guide-me-home" lighting with the following additional options: - selection of the lighting duration of 15, 30 or 60 seconds in the vehicle parameters
in the vehicle configuration menu, - automatic activation of "guide-me-home" lighting when automatic lillumination of headlamps is in operation.
Parking lamps
Side markers for the vehicle by illumination of the sidelamps on the traffic side only.  Within one minute of switching off the
ignition, operate the lighting control stalk up or down depending on the traffic side (for example: when parking on the left; lighting control stalk upwards; the right hand sidelamps are on). This is confirmed by an audible signal and illumination of the corresponding direction indicator warning lamp in the instrument panel. To switch off the parking lamps, return the lighting control stalk to the central position.

The sidelamps and dipped beam headlamps are switched on automatically, without any action on the par t of the driver, when a low level
of external light is detected or in cer tain cases of activation of the windscreen wipers. As soon as the brightness returns to a sufficient level or after the windscreen wipers are switched off, the lamps are switched off automatically.
Automatic illumination of headlamps
Activation
 Turn the ring to the "AUTO" position. The automatic illumination of headlamps is accompanied by a message in the screen.
Deactivation
 Turn the ring to another position. Deactivation is accompanied by a message in the screen.
Associated with the automatic "Guide-me-home" lighting
Association with the automatic lighting provides the "guide-me-home" lighting with the following additional options: - selection of the lighting duration of 15, 30 or 60 seconds in the vehicle parameters
in the vehicle configuration menu, - automatic activation of "guide-me-home" lighting when automatic lillumination of headlamps is in operation.
Parking lamps
Side markers for the vehicle by illumination of the sidelamps on the traffic side only.  Within one minute of switching off the
ignition, operate the lighting control stalk up or down depending on the traffic side (for example: when parking on the left; lighting control stalk upwards; the right hand sidelamps are on). This is confirmed by an audible signal and illumination of the corresponding direction indicator warning lamp in the instrument panel. To switch off the parking lamps, return the lighting control stalk to the central position.

191Driving
With the ignition on or the engine running, to release the parking brake, press on the brake pedal or the accelerator, pull then release control A .
Manual release
Before leaving the vehicle, check that parking brake warning lamp in the instrument panel is on fixed, not flashing.
Manual application
With the vehicle stationary, to apply the parking brake whether the engine is running or off, pullcontrol lever A .
The application of the parking brake is confirmed by:
- illumination of the braking warning lamp and of the P warning lamp in the control lever A ,
- display of the message "Handbrake on".
When the driver’s door is opened with the engine running, a message is displayed accompanied by an audible signal if the parking brake has not been applied.
The full application of the parking brake is confirmed by:
- the braking warning lamp and the P warning lamp in the control lever A going off,
- display of the message "Handbrake off ".
If you pull control lever A without pressing the brake pedal, the parking brake will not be released and a warning lamp will come on in the instrument panel.
Maximum application
If necessary, you can make a maximum application of the parking brake. This is obtained by means of a long pull on the control lever A , until you see the message "Handbrake on maximum" and a beep is heard. Maximum application is essential: - in the case of a vehicle towing a caravan or a trailer, if the automatic functions are activated but you are applying the parking brake manually, - when the gradient you are parked on may vary (e.g. on a ferry, on a lorry, during towing),
In the case of towing, a loaded vehicle or parking on a gradient, make a maximum application of the parking brake then turn the front wheels towards the pavement and engage a gear when you park. After a maximum application, the release time will be longer.