seat adjustment Citroen DS4 DAG 2010.5 1.G Owner's Manual

Lighting dimmer fixed. The lighting dimmer is making an adjustment. You can adjust the level of illumination of the instruments between 1 and 16.
Passenger's airbag system fixed on the seat belt and passenger's front airbag warning lamps display.
The control switch, located in the glove box, has been placed in the "ON" position.The passenger's front airbag is activated. In this case, do not install a "rear facing" child seat.
Move the control switch to the "OFF" position to deactivate the passenger's front airbag. In this case, you can install a "rear facing" child seat.
Automatic wiping fixed. The wiper control is pushed downwards. Automatic front wiping is activated.
Warning lampis onCauseAction/Obser vations
Stop & Star t
fixed. The Stop & Star t system has put the engine in STOP mode at a vehicle stop (traffic lights, traffic jam, or other...).
The warning lamp goes off and the engine restar ts automatically in START mode, as soon as you want to move off.
flashes for a few seconds, then goes off.
STOP mode is temporarily unavailable. or START mode is invoked automatically.
Refer to "Driving - § Stop & Star t" for special cases with STOP mode and START mode.
Parking space sensors fixed. The parking space sensors function is selected. To star t measurement, operate the direction indica tor on the side of the space to be measured, and do not exceed 12 mph (20 km/h). A message is displayed once the measurement has been completed.

Front seats Seat consisting of a seat cushion, a seat back and a head restraint which can all be adjusted to adapt your position for ease of driving and comfor t.
Manual adjustments
Forwards-backwards adjustment
 Raise the control and slide the seat
for wards or backwards.
Driver's or passenger's seat height adjustment
 Pull the control upwards to raise or push it downwards to lower, as many times as necessary, to obtain the position required.
Seat back angle adjustment
 Turn the control knob to adjust the seat
backrest angle.
As a safety measure, seat adjustments should only be done when stationary.

Heated seats control
With the engine running, the front seats can be heated separately.  Use the adjustment dial, placed on the side of each front seat, to switch on and select the level of heating required: 0: Off. 1: Low. 2: Medium. 3: High.
Additional adjustments
Head restraint height and angle adjustment
 To raise a head restraint, pull it upwards.  To remove the head restraint, press the lug A and pull the head restraint upwards.  To put the head restraint back in place, engage the head restraint stems in the openings keeping them in line with the seat back.  To lower the head restraint, press the lug Aand the head restraint at the same time.  To adjust the angle of the head restraint, tilt
its lower par t for wards or rear wards.
The head restraint is fitted with a frame with notches which prevents it from lowering; this is a safety device in case of impact. The adjustment is correct when the upper edge of the head restraint is level with the top of the head. Never drive with the head restraints removed; they must be in place and
adjusted correctly.

87Comfort
Front seats
Seat consisting of a seat cushion, a seat back and a head restraint which can all be adjusted to adapt your position for ease of driving and comfor t.
Driver's seat electric adjustments
Forwards-backwards adjustment
 Push the control for wards or rear wards to
slide the seat.
Seat cushion height and angle adjustment
 Tilt the rear par t of the control upwards or downwards to obtain the required height.  Tilt the front par t of the control upwards or downwards to obtain the required angle.
Seat back angle adjustment
 Tilt the control for wards or rear wards to
adjust the angle of the seat back.
The electrical functions of the driver's seat are deactivated approximately one minute after the ignition is switched off. To reactivate them, switch on the ignition.

Heated seats control
With the engine running, the front seats can be heated separately.  Use the adjustment dial, placed on the side of each front seat, to switch on and select the level of heating required: 0: Off. 1: Low. 2: Medium. 3: High.
Additional adjustments
Head restraint height and angle adjustment
 To raise a head restraint, pull it upwards.  To remove the head restraint, press the lug A and pull the head restraint upwards.  To put the head restraint back in place, engage the head restraint stems in the openings keeping them in line with the seat back.  To lower the head restraint, press the lug Aand the head restraint at the same time.  To adjust the angle of the head restraint, tilt
its lower par t for wards or rear wards.
The head restraint is fitted with a frame with notches which prevents it from lowering; this is a safety device in case of impact. The adjustment is correct when the upper edge of the head restraint is level with the top of the head. Never drive with the head restraints removed; they must be in place and
adjusted correctly.

Storing driving positions
System which registers the electrical settings of the driver's seat and door mirrors. It enables you to store and recall two positions using the buttons on the side of the driver's seat.
Storing a position
Using buttons M/1/2
 Switch on the ignition.  Adjust your seat and the door mirrors.  Press button M , then press button 1 or 2within four seconds. An audible signal indicates that the position has been stored.
Recalling a stored position
Ignition on or engine running
 Press button 1 or 2 to recall the corresponding position. An audible signal indicates the end of the adjustment.
Storing a new position cancels the previous position.
You can interrupt the current movement by pressing button M , 1 or 2 or by using one of the seat controls. A stored position cannot be recalled
while driving. Recalling stored positions is deactivated 45 seconds after switching off the ignition.

Automatic adjustment of Xenon headlamps
Do not touch the xenon headlamp bulbs. Contact a CITROËN dealer or a
qualified workshop.
In order to avoid causing a nuisance to other road users, this system corrects the height of the xenon headlamp beams automatically and when stationary, in relation to the load in the vehicle.
If a malfunction occurs, this warning lamp and/or the ser vice warning lamp is displayed on the instrument panel, accompanied by an audible signal and a message in the screen. The system then places your headlamps in the lowest position.
Manual adjustment
of halogen
headlamps
To avoid causing a nuisance to other road users, the height of the halogen headlamps should be adjusted according to the load in the vehicle. 0. 1 or 2 people in the front seats.
-. 3 people. 1. 5 people. -. Intermediate setting. 2. 5 people + maximum authorised load. -. Intermediate setting. 3. Driver + maximum authorised load.
The initial setting is position "0" .

Safety
Seat belts
Front seat belts
The front seat belts are fitted with a pretensioning and force limiting system. This system improves safety in the front seats in the event of a front or side impact.
Depending on the severity of the impact, the pretensioning system instantly tightens the seat belts against the body of the occupants. The pretensioning seat belts are active when the ignition is on. The force limiter reduces the pressure of the seat belt on the chest of the occupant, so improving their protection.
Fastening
 Pull the strap, then inser t the tongue in the buckle.  Check that the seat belt is fastened
correctly by pulling the strap.
Unfastening
 Press the red button on the buckle.  Guide the seat belt as it reels in.
Seat belt not fastened/unfastened warning lamp
When the ignition is switched on, this warning lamp comes on in the instrument panel if the driver and/or the front passenger has not fastened their seat belt. From approximately 12 mph (20 km/h) this warning lamp flashes for two minutes accompanied by an audible signal of increasing volume. Once these two minutes have elapsed, this warning lamp remains on until the driver and/
or the front passenger fastens their seat belt.
Height adjustment
 To lower the attachment point, squeeze the control A and slide it downwards.  To raise the attachment point, slide the control A upwards.

The driver must ensure that passengers use the seat belts correctly and that they are all restrained securely before setting off. Wherever you are seated in the vehicle, always fasten your seat belt, even for shor t journeys. Do not interchange the seat belt buckles as they will not fulfil their role fully. The seat belts are fitted with an iner tia reel permitting automatic adjustment of the length of the strap to your size. The seat belt is stowed automatically when not in use. Before and after use, ensure that the seat belt is reeled in correctly. The lower par t of the strap must be positioned as low as possible on the pelvis. The upper par t must be positioned in the hollow of the shoulder. The iner tia reels are fitted with an automatic locking device which comes into operation in
the event of a collision, emergency braking or if the vehicle rolls over. You can release the device by pulling firmly on the strap and
releasing it so that it reels in slightly.
In order to be effective, a seat belt must: - be tightened as close to the body as possible, - be pulled in front of you with a smooth movement, checking that it does not twist, - be used to restrain only one person, - not bear any trace of cuts or fraying, - not be conver ted or modified to avoid affecting its per formance. In accordance with current safety regulations, for all repairs on your vehicle, go to a qualified workshop with the skills and equipment needed, which a CITROËN dealer is able to provide. Have your seat belts checked regularly by a CITROËN dealer or a qualified workshop, par ticularly if the straps show signs of damage. Clean the seat belt straps with soapy water or
a textile cleaning product, sold by CITROËN dealers. After folding or moving a seat or rear bench seat, ensure that the seat belt is positioned and reeled in correctly.
Recommendations for children
Use a suitable child seat if the passenger is less than 12 years old or shor ter than one and a half metres. Never use the same seat belt to secure more than one person. Never allow a child to travel on your lap.
In the event of an impact
Depending on the nature and seriousness of the impact , the pretensioning device may be deployed before and independently of the airbags. Deployment of the pretensioners is accompanied by a slight discharge of harmless smoke and a noise, due to the activation of the pyrotechnic car tridge incorporated in the system. In all cases, the airbag warning lamp comes on. Following an impact, have the seat belts system checked, and if necessary replaced, by a CITROËN dealer or a qualified workshop.