change time Citroen DS5 RHD 2016 1.G User Guide

285
Selecting a station
The exterior environment (hills, buildings,
tunnel, car park, below ground...) may
prevent reception, even in RDS station
tracking mode. This phenomenon is
normal in the propagation of radio waves
and is in no way indicative of a fault with
the audio system.Press SOUR
c
E o

r SR c
se
veral
times in succession and select radio.
Press BA
n

d
t
o select a waveband.
Press LIST to display the list of
stations received in alphabetical
o r d e r.
Select the desired radio station and
confirm by pressing OK.
A press changes to the next or
previous letter (e.g. A, B, D, F, G,
J,
K, ...).
Audio
A long press on LIST builds or
updates the list of stations; audio
reception is cut momentarily.
Audio and Telematics

Steering mounted controls








Media: change the multimedia
source.
Telephone: call.
Call in progress: access to the
telephone menu (end call, secret
mode, hands-free mode).
Telephone, press and hold: reject an
incoming call, end a call; when there
is no call in progress, access to the
telephone menu.
CarPlay
®
or MirrorLink TM
, press and
hold: start voice recognition on your
smartphone via the system.
Decrease volume.


Radio, rotate: automatic search for
the previous / next station.
Media, rotate: previous / next track.
Press: confirm a selection.
Radio: display the list of stations.
Media: display the list of tracks.
Radio, press and hold: update the list
of stations received.

Increase volume.

31
20
29 Audio and Telematics


Select change of source.
Press on Radio Media
to display the
primary page.

Select " DAB Radio
".

Select " List
" in the primary page.

Select the radio station from the list offered.

Press on Radio Media
to display the
primary page.

Press on the secondary page.

Select " Settings
".

Select " Radio
".

Select " Digital/FM auto
tracking
" then " Confirm
".










DAB / FM auto tracking







Digital radio


"DAB" does not cover 100% of the
territory.
When the digital radio signal is poor,
"DAB/FM station tracking" allows you to
continue listening to the same station,
by automatically switching to the
corresponding "FM" analogue station
(if there is one).
If "DAB/FM station tracking" is
activated, there is a difference of a few
seconds when the system switches to
"FM" analogue radio with sometimes a
variation in volume.
When the digital signal is restored, the
system automatically changes back to
"DAB".
Digital radio provides higher quality
reception and also the graphical display
of current information on the radio
station being listened to. Select "List" in
the primary page.
The range of multiplexes available is
displayed in alphabetical order.

If the "DAB" station being listened to
is not available on "FM" (" DAB/FM
"
option greyed out), or "DAB/FM station
tracking" is not activated, the sound
will cut out while the digital signal is too
weak.


or

Select " Radio list
" in the secondary
page.

3
Media












USB player




















Selecting the source


The steering mounted SRC
(sourc e)
button can be used to go to the next
media source, available if the source
is active.


Press OK
to confirm the selection.

Select change of source.
Press on Radio Media
to display the
primary page.

The system builds playlists (in temporary
memory), an operation which can take from
a few seconds to several minutes at the first
connection.
Reduce the number of non-music files and the
number of folders to reduce the waiting time.
The playlists are updated every time the
ignition is switched off or connection of a USB
memory stick. The lists are memorised: if they
are not modified, the subsequent loading time
will be shorter.

Insert the USB memory stick into the USB port
or connect the USB device to the USB port
using a suitable cable (not supplied).





















Auxiliary (AUX) socket










CD player


Insert the CD in the player.

Connect the portable device (MP3 player…) to
the auxiliary Jack socket using an audio cable
(not supplied).

First adjust the volume of your portable device
(to a high level). Then adjust the volume of your
audio system.
Display and management of the controls are
via the portable device.

Choose the source.

11
1
8
9
10
41 Audio and Telematics


Press on Settings
to display the
primary page.

Press on "Settings" to display the
primary page.
Press on Settings
to display the
primary page.

Press on the secondary page.

Press on the secondary page
Press on the secondary page.

Select " System Settings
".

Select " Time/Date
" to change the
time zone, synchronisation with GPS,
the time and its format, then the date.
Select " Screen settings
".

Select " Units
" to change the units
of distance, fuel consumption and
temperature.
Select " Languages
" to change
language.



)
Select the " Settings
" menu.

Activate or deactivate " Activate
automatic text scrolling
" and
" Activate animations
".

Select " Delete data
" to delete the
list of recent destinations, personal
points of interest, contacts in the list.
Select " Calculator
" to display a
calculator.



)
In the secondary page, press on
" Time/Date
".


Choose the item then select " Delete
".
Select " Calendar
" to display a
calendar.




)
Modify the settings using the
number keypad, then confirm.

)
Press " Confirm
" to save and
quit.



)
Select " Adjust time
" or " Adjust
date
".


Select " Factor y settings
" to return
to the original settings.







Modifying system settings























Setting the date and time


When setting the time, you can select
" Satellite synchronisation
", so that the time is
adjusted automatically by satellite reception.

1 Audio and Telematics







DS Connect Nav


GPS satellite navigation - Connectivity - Multimedia audio - Bluetooth ®
telephone


Contents
First steps 2
Steering mounted controls 4
Menus 5
Voice commands 6
Navigation 12
Connected navigation 28
Connectivity 38
Radio Media 50
Te l e p h o n e 6 2
Settings 74
Frequently asked questions 84

The system is protected in such a way that it will only operate in
your vehicle.

The link below gives access to OSS (Open Source Software)
codes for the system.
http://www.psa-peugeot-citroen.com/oss
As a safety measure and because it requires sustained attention
by the driver, the pairing of a Bluetooth mobile telephone with
the Bluetooth hands-free system of your audio system must be
done with the vehicle stationary
and the ignition on.
The display of the energy economy mode message signals that
a change to standby is imminent. Refer to the Energy economy
(mode) section of your vehicle's handbook.

Steering mounted controls



Media
(short press): change the
multimedia source.

Te l e p h o n e
(short press): call.

Call in progress
(short press):
access to telephone menu.

Te l e p h o n e
(long press): reject an
incoming call, end call, access to
telephone menu.






Voice commands
:
Short press, system voice
commands.
Long press, smartphone voice
commands via the system.

Decrease volume.



Radio
(rotate): automatic search for
the previous / next station.

Media
(rotate): previous / next track,
move in a list.

Shor t press
: Confirm a selection.
Other than selection, access to
presets.

Radio
: display the list of stations.

Media
: display the list of tracks.

Radio, press and hold
: update the
list of stations received.

Increase volume.

7
28
27
26
29
30
31 Audio and Telematics



Level 1



Level 2



Level 3



Comments




Navigation


Select the orientation of the map; north up,
vehicle direction up or perspective.


Navigation



TOMTOM TR AFFIC

On connection of the system to a network,
"TOMTOM TR AFFIC" is displayed instead of
"TMC", for use of all of the options available, in
real time.


Navigation


Weather

Select the options.
The map display the route chosen, depending on
options.
Stations


Car park


Tr a f f i c


Danger area


Map color
Select the display mode for the map.

POI on map
Commercial
Select the POIs available. Geographic
Leisure
Public
Tr a v e l
Confirm Save the options.

View map
Modify city Select or change a city.
Zoom out.
Zoom in.

1
9
59 Audio and Telematics


Select the audio source.
Press on Radio Media
to display the
primary page.

Press on " Band
" to select the " DAB
"
waveband.

Press on Radio Media
to display the
primary page.

Press on the " OPTIONS
" button to
go to the secondary page.









DAB / FM auto tracking








Digital radio


"DAB" does not cover 100% of the
territory.
When the digital radio signal is poor,
"DAB/FM auto tracking" allows you to
continue listening to the same station,
by automatically switching to the
corresponding "FM" analogue station
(if there is one).
If "DAB / FM auto tracking" is activated,
there is a difference of a few seconds
when the system switches to "FM"
analogue radio with sometimes a
variation in volume.
Once the digital signal is restored, the
system automatically changes back to
"DAB".
Digital radio provides higher quality
reception.
The different multiplexes offer a
choice of radio stations arranged in
alphabetical order.

If the "DAB" station being listened to
is not available on "FM" (" DAB/FM
"
option greyed out), or "DAB/FM auto
tracking" is not activated, the sound
will cut out while the digital signal is too
weak.


Select " Radio settings
".

Select " General
".

Activate / Deactivate " Station
follow
".

Press on " Confirm
".

111
11
12
13
9
101

Press on Settings
to display the
primary page.
Press Settings
to display the primary
page.
Press on Settings
to display the
primary page.

Press on the " OPTIONS
" button to
go to the secondary page.
Press the " OPTIONS
" button to go to
the secondary page.
Press on the " OPTIONS
" button to
go to the secondary page.

Select " System settings
".

Select " Screen configuration
".

Select " Units
" to change the units
for distance, fuel consumption and
temperature.
Select " Languages
" to change the
language.


Activate or deactivatre " Automatic
scrolling
".

Adjust the brightness of the screen.
Select " Factor y settings
" to return
to the initial settings.

Select " System info
" to display the
versions of the different modules
installed in the system.







Modifying system settings


Returning the system to factory settings
activates the English language by
default.
Select " Animation
".

Select " Brightness
".


Select the language


Press on Settings
to display the
primary page.

Press on the " OPTIONS
" button to
go to the secondary page.

Select " Setting the time- date
".










Setting the date