Citroen JUMPER 2016 2.G Owner's Manual

149
jumper_en_Chap08_Aide-rapide_ed01-2015
When using a high pressure washer
on stubborn dirt, do not persist on
the headlamps, the lamps and their edges
to avoid damaging their lacquer finish and
seals.
cHAnGInG A B u LB
t
ypes of bulb
Various types of bulb are used on your
vehicle.
To remove them:
type

A


Entirely glass bulb: pull gently

as it is fitted by pressure.
type B


Bayonet bulb: press on the bulb

then turn it anticlockwise.
type

c c ylindrical bulb: move aside the
contacts. For removing and refitting the screws,
use the screwdriver stowed in the tool
box under the front passenger's seat.
Carry out the operations in reverse order to
refit each bulb.
type

d - E
Halogen bulb: release the

retaining spring from its
housing.
Always replace a failed bulb with


a new bulb of the same type and
specification.
Failed bulb or lamp
QUiCK HELP
8

150
jumper_en_Chap08_Aide-rapide_ed01-2015
1 - Main beam headlamps
type
d , H7 - 55 W
-
r emove the cover by pulling on the
rubber tongue.
-

Disconnect the electrical connector
.
-
r elease the retaining spring by pressing
on the central clip.
-

Change the bulb taking care to align the

metal part with the groove on the lamp. 2 -
d ipped beam headlamps
type

d , H7 - 55 W
- r emove the cover by pulling on the
rubber tongue.
- Disconnect the electrical connector .
- r elease the retaining spring by pressing
on the central clip.
-

Change the bulb taking care to align the

metal part with the grooves on the lamp.
Front lamps
3 - direction indicators
type A

, WY 21 W - 21 W
-
r emove the cover by pulling on the
rubber tongue.
-

T
urn the bulb holder a quarter turn
anticlockwise.
-

Change the bulb.
o

pen and secure the bonnet with the stay.
To access the bulbs, reach behind the
headlamp unit.
If necessary you can remove the headlamp:
-

Depending on the country of sale,


remove the very low temperature
protection padding by sliding it towards
the outside of the vehicle.
-
Disconnect the electrical connector by

removing its locking ring.
-
r
emove the two headlamp fixing
screws.
-

Move the headlamp towards the centre


of the vehicle to extract it from its
sliders.
o

n the left hand side, take care not to
dislodge the bonnet stay.
Failed bulb or lamp

151
jumper_en_Chap08_Aide-rapide_ed01-2015
Halogen bulbs must be changed after
the headlamp has been off for several
minutes (risk of serious burns). Do not touch
the bulb directly with your fingers, use a
lint-free cloth.
When each operation has been completed,
check the operation of the lamps.
5 - Front foglamps
type E

, H11 - 55 W
-

Turn the steering so that the wheel on the
side in question is turned fully inwards.
- remove the screw located in the wheel
arch.
-
r emove the protective cover.
LE
d
daytime running lamps
These light-emitting diode (LED) lamps
serve as both daytime running lamps and
sidelamps.
i

f your vehicle is fitted with LED daytime
running lamps, contact a C
i
T
roën
dealer.
4 - Sidelamps / daytime running lamps
type A

, W21/5W - 21W and 5W
-
r
emove the cover by pulling on the
rubber tongue.
-

T

urn the bulb holder a quarter of a turn
anti-clockwise.
-

Change the bulb.
-
r emove the fixing clip and disconnect
the electrical connector.
-
T
urn and disengage the bulb holder
-
Change the bulb taking care to align the

metal part with the grooves on the lamp.
Failed bulb or lamp
QUiCK HELP
8

152
jumper_en_Chap08_Aide-rapide_ed01-2015
courtesy lamps
type c , 12 V 10 W - 10 W
-
Press at the points indicated by the

arrows, then remove the courtesy lamp.
-
o pen the protective flap.
-

Change the bulb moving aside the two

contacts.
-

Ensure that the new bulbs are secured

correctly between the two contacts.
-

Close the protective flap.
-


Fix the courtesy lamp in its housing and

ensure that it is secured correctly.
Side marker lamps
type A , W5W - 5W
- i f your vehicle is fitted with these lamps
(L4 body), remove the two fixing screws.
-

Pull the bulb holder to release it from the

lugs.
-

Pull the bulb out and change it.
direction indicator side
repeaters
type A , W 16 W F - 16 W
-
Move the mirror glass to access the

screws.
-
r emove the two fixing screws.
-

Pull the bulb holder to release it from the

lugs.
-

Pull the bulb out and change it. Front /

r ear
Failed bulb or lamp

153
jumper_en_Chap08_Aide-rapide_ed01-2015
rear lamps
Carry out these operations in reverse order
to fit the new bulb.
1.
Brake lamps


t
ype B,

P21W - 21W
2.

Brake/sidelamps


t
ype B,

P21/5W - 21W and 5W
3.
d
irection indicators

t
ype B,

PY 21W - 21W
4.
r
eversing lamps

t
ype A,

W16W - 16W
5.

Foglamp


t
ype A,

W16W - 16W -
i dentify the failed bulb then open the
rear doors.
- r emove the corresponding access cover
by removing the seven fixing screws
(van) or


r emove the corresponding access cover
by pulling on its grip to unclip it (combi).
-

Disconnect the electrical connector by

pressing on its central tongue.
-
r emove the two fixing nuts of the lens.
-

Pull the lens from the outside.-

r emove the six bulb holder fixing
screws.
-
Spread the three retaining tongues and

remove the bulb holder from its housing.
-
Change the bulb.
For more information on the bulbs,

refer to the table "Types of bulb or
lamp".
Failed bulb or lamp
QUiCK HELP
8

154
jumper_en_Chap08_Aide-rapide_ed01-2015
third brake lamp
type A, W5W - 5W (x 4)
- r emove the two lamp fixing screws.
-
r emove the lamp by pulling it towards
you.
number plate lamps
type c , C5W - 5W
-
Press the point, indicated by the arrow
,
then remove the plastic lens.
-
r emove the failed bulb by moving aside
the two contacts.
-

With the new bulb in place, ensure that

it is secured correctly between the two
contacts.
-
r eplace the plastic lens and press on it
to lock it in place. -
r emove the bulb holder by squeezing
the two tabs.
- r emove the failed bulb by pulling it out.
-

Change the bulb.
Failed bulb or lamp

155
jumper_en_Chap08_Aide-rapide_ed01-2015
cHAnGInG A WIPE r BLA d E
The steps, located in the front bumper,
enable you to reach the blades and the
screenwash jets.changing a front wiper blade
raise the wiper arm.
Unclip the blade by pressing the button and
remove it by pulling it outwards.
Fit the new blade and ensure that it is
secured correctly.
r

eturn the wiper arm to the normal position.
Check that the screenwash or
headlamp wash jets are not blocked.
Worn wiper blade
QUiCK HELP
8

156
jumper_en_Chap08_Aide-rapide_ed01-2015
Parking the vehicle
Where possible, park the vehicle on level,
stable and non-slippery ground.
Apply the parking brake, switch off the
ignition and engage first gear.
Wear a high visibility vest and position the
warning triangle on the road.
You must ensure that the occupants get out
of the vehicle and wait in a safe location.
tools
These are stowed in a box located under the
front passenger seat.
-
T
urn the button a quarter of a turn then
pull the box.
-

After use, press the button then turn it a

quarter of a turn to secure the box.
A.

Long socket.
B.

Bar.
c

. Jack.
d

. Wheelbrace.
E.

Screwdriver (handle and bits).
F.


r emovable towing eye.
cHAnGInG A WHEELPneumatic suspension
i
f you vehicle is fitted with this system, you
must first activate vehicle lifting mode.
Press the two controls simultaneously for at
least 5 seconds; their indicator lamps come
on.
This mode is deactivated automatically after
changing a wheel, once the speed of the
vehicle has exceeded 3 mph (5 km/h).
The jack and the tool kit are specific to


your vehicle. Do not use them for other
purposes.
n

ever go underneath a vehicle supported
only by a jack (use an axle stand).
Puncture

157
jumper_en_Chap08_Aide-rapide_ed01-2015
● For versions with alloy wheels, remove
the three fixing screws I from the
strap
j
.
●


Remove the assembly from inside the

alloy wheel.
Spare wheel
The spare wheel retaining bolt is located
below the bumper on the right.
-
i nstall the long socket A , the
wheelbrace
d
and the bar

B on the
retaining bolt.
-

T
urn the assembly anti-clockwise to
lower the wheel.
-

T
urn to the full extent, indicated by an
increase in the force required.
-

Having fully unwound the cable, take out

the spare wheel under the vehicle. ●
For versions with steel wheels, unscrew
the grip G .
●

Remove the carrier
H from the outer part
of the steel wheel.
-
r elease the spare wheel and place it
near the wheel to be changed.
-
i f possible, place a chock against the
wheel diagonally opposed to the wheel
to be changed.
Puncture
QUiCK HELP
8

158
jumper_en_Chap08_Aide-rapide_ed01-2015
- Extend the jack using the wheelbrace d
and trhe bar B until the wheel is a
few
centimetres off the ground.
-

Unscrew the bolts fully and remove the

wheel to be repaired.
-
Position the jack
c at one of the four

locations provided on the underbody
near the wheels.
i

f your vehicle has a folding foot board, the
jack must be positioned at 45°.
removing the wheel to be repaired
- remove the trim (depending on version)
using the screwdriver E as a lever.
-
r elease the bolts using the
wheelbrace
d
and the bar

B.
Puncture