Citroen XSARA 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine ENGINE
197
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1EP18VD
Setting the timing.
Perform the preliminary operations for checking the timing up to removing tool [1]at «a»for immobiling the
engine flywheel.
Refit screw
(8).
Rotate the crankshaft to bring the camshaft towards its pegging point.
Peg the camshaft, using tool
[2](oil the pegs).
WARNING: Do not press or damage the track which is the target for the engine speed sensor (14).
Peg the crankshaft at «b», using tool [3].
Remove:
The timing protector
(13).
The engine speed sensor
(14).
Slacken the screw
(12)of the tensioner roller, keeping it slack with the aid of a hexagonal spanner at
«c».
Detension the belt by pivoting the tensioner roller
(clockwise).
Remove the timing belt, commencing with the coolant pump pinion.
Peg the pulley
(15), using a 5 mmdiameter peg at «d».
C3

Downloaded from www.Manualslib.com manuals search engine 198
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1EP18WD
Setting the timing (continued).
Chec
king the setting.
IMPERATIVE: Just prior to refitting, carry out the following tests.
Check that:
the rollers and the coolant pump operate freely
(no play and no tight spot).
there are no traces of oil
(from the crankshaft and camshaft sealing rings).
there is no leak of coolant fluid
(from the coolant pump).
the target track of the engine speed sensor
(14)is not damaged or scratched
(if necessary replace the defective components).
Refitting.
Fit the timing belt on the crankshaft pinion.
Position the belt on the guide roller, with the belt well tensioned.
Refit:
The timing protector
(13).
The sensor
(14).
C3

Downloaded from www.Manualslib.com manuals search engine ENGINE
199
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1EP18XC
Setting the timing (continued).
Chec
ks (continued).
Reposition the timing belt, belt at «e»well tensioned, in the following order:
Guide roller
(17).
Camshaft pulley
(16).
Fuel high pressure pump pulley
(15).
Coolant pump pinion
(18).
Tensioner roller
(19).
Remove the
5 mmdiameter peg at «d».
Adjusting the fitting tension of the belt.
Action the tensioner roller (19)to align the marks «f»and «g», avoiding detensioning the timing belt,
with the aid of a male hexagonal spanner, at
«c».
If this is not successful, repeat the operation to tension the belt.Hold the tensioner roller in position
(19).
Tighten the tensioner roller, tightening to
3,7 ±0,3 m.daN.
Check the position of the tensioner roller
(the alignment of the marks «f»and «g»should be correct).
Remove tools
[2]and [3].
Turn the crankshaft
six rotations(clockwise).
C3

Downloaded from www.Manualslib.com manuals search engine 200
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1EP18XC
Adjusting the timing belt tension (continued).
IMPERATIVE: Never rotate the engine backwards.WARNING:
Do not touch or damage the track of the target of the engine speed sensor (14).
Peg the crankshaft, using tool
[3].
Check the position of the tensioner roller
(the alignment of the marks «f»and «g»should be correct).
If this is not the case, repeat the operation to tension the belt.Peg the camshaft pulley, using tool
[2].
IMPERATIVE: Should it be impossible to peg the camshaft, check that the offset between the
camshaft hole and the pegging hole is not more than 1 mm. If the offset is too great, repeat theoperation.
Remove the pegs [2]and [3].
Refit tool
[1]at «a».
Remove the screw
(8).
Complete the refitting.
C3

Downloaded from www.Manualslib.com manuals search engine ENGINE
201
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1BP304D
Tools.
[1]
Flywheel setting peg: ().0194.C
[2]
Camshaft setting peg:().0194.B
[3]
Crankshaft setting peg: ().0194.A
Checking and setting the timing.
Removing.
Raise and support the vehicle, wheels hanging.
Disconnect the positive and negative terminals of the battery.
Remove: The front RH wheel.
The front RH splashshield.
The accessories drive belt
(see corresponding operation).
Uncouple: The fuel supply unions
(1).
The air/air heat exchanger inlet and outlet pipes
(3).
The exhaust line
(at the flexible pipe).
Disconnect the connecter at
«a».
Remove and move aside the power steering fluid reservoir
(6).
Uncouple, plug and move aside the tube
(2).
Support the engine with a roller jack equipped with a block.
Remove the engine supports
(4)and (5).
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 202
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1EP1E3D
Rotate the engine to drive it in its normal direction of rotation.
Peg the flywheel, using tool
[1]at «b».
Move aside the harness
(7).
Remove:
The engine support
(8).
The screw
(10).
The accessories drive pulley
(9).
The lower timing cover
(11).
The upper timing cov
(12).
The tool
[1].
B1BP305C
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 203
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refit the screw (10).
Rotate the crankshaft six times (clockwise).
IMPERATIVE: Never turn it backwards.
Peg the camshaft at «c», using tool [2](oil the peg).WARNING:The magnetic track should not show any sign of damage and should not be
approached by any other magnetic source.
Peg the crankshaft at
«d», using tool [3].
ESSENTIAL: Should it not be possible to peg the camshaft, check that the offset bet
ween the camshaft pinion hole and the pegging hole is not more than 1 mm.If it is
more,repeat the operation to position the timing belt
(see corresponding operation).
Note:
The index «e»of the dynamic tensioner roller should be centred in the interval «d»Check the correct positioning of the index «e».
If it is not correct, repeat the operation to tension the timing belt (see corresponding operation).
Remove tools [2]and [3].
B1EP1E4DB1EP1E5C
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 204
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refitting.
Refit tool [1]at «b».
Remove the screw (10).
Refit:
The upper timing cover
(12).
The lower timing cover (11).
The accessories drive pulley (9).
The screw (10).
Tightening torqueScrew (10)Pretighten to:3 ± 0,3 m.daN.
Angular tighten:180°±5°.
Remove tool [1].
Refit:
The engine support
(8), tighten to 5,5 ± 0,4 m.daN.
The engine support (4), tighten to 6,1 ±0,6 m.daN.
The engine support (5), tighten to 2,5 ±0,2 m.daN.
The electrical harness (7).
The power steering fluid reservoir (6).
XSARA PICASSO
Couple:
The tube (2).
The exhaust line, tighten the clip to 2,5 ± 0,3 m.daN.
The fuel unions (1).
The air/air heat exchanger inlet and outlet pipes (3).
Connect the connector at «a».
Refit:
The accessories drive belt
(see corresponding operation).
The front RH splashshield
(see corresponding operation).
The front RH wheel, tighten to 9 ±1 m.daN.
Reconnect the positive and negative terminals of the battery.
IMPERATIVE:Perform the operations that are necessary following a
reconnection of the battery (see corresponding operation).

Downloaded from www.Manualslib.com manuals search engine 205
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1BP304D
Tools.
[1]
Flywheel setting peg: ().0194.C
[2]
Camshaft setting peg:().0194.B
[3]
Crankshaft setting peg: ().0194.A
Checking and setting the timing.
Removing.
Raise and support the vehicle, wheels hanging.
Disconnect the positive and negative terminals of the battery.
Remove: The front RH wheel.
The front RH splashshield.
The accessories drive belt
(see corresponding operation).
Uncouple:
The fuel supply unions
(1).
The air/air heat exchanger inlet and outlet pipes
(3).
The exhaust line
(at the flexible pipe).
Disconnect the connecter at
«a».
Remove and move aside the power steering fluid reservoir
(6).
Uncouple, plug and move aside the tube
(2).
Support the engine with a roller jack equipped with a block.Remove the engine supports
(4)and (5).
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 206
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1EP1E3D
Rotate the engine to drive it in its normal direction of rotation.
Peg the flywheel at
«b». using tool [1].
Move aside the harness
(7).
Remove:
The engine support
(8).
The screw
(10).
The accessories drive pulley
(9).
The lower timing cover
(11).
The upper timing cov
(12).
The tool
[1].
B1BP305C
XSARA PICASSO