engine lock Citroen XSARA 2004 1.G Manual PDF

Downloaded from www.Manualslib.com manuals search engine 345
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
NOTE:The «shift lock»«P».
Unlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed.
Move the gear selection lever out of position
«P».
Unlocking the «SHIFT LOCK»(with an operating fault).NOTE:It is impossible to unlock the «shift lock»
«Shift lock».
Gear lever position switch. Automatic gearbox ECU.
Electrical harnesses.
Battery voltage.
Remove:
The gear lever knob
(1)(pull upwards).
The cover (2)(Unclip).
The top of the central console (3).
Unlock the «shift lock» (4)with the aid of a screwdriver.
Move the gear selection lever out of position «P».
Engine: KFV
C3
C5FP0ETCB2CP3GZC

Downloaded from www.Manualslib.com manuals search engine 346
CLUTCH
GEARBOX
TRANSMISSION
XSARAAL4 AUTOMATIC GEARBOX
Engines: NFU RFN RHZ
SHIFT LOCK.
NOTE:
The «shift lock»«P».
U
nlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed. Move the gear selection lever out of position
«P».
Unlocking the «SHIFT LOCK»(with an operating fault).NOTE:It is impossible to unlock the «shift lock»
«Shift lock».
Gear lever position switch.
Automatic gearbox ECU.
Electrical harnesses. Battery voltage.
Remove:
The cover
(1).
Unlock the «shift lock» (2) with the aid of a screwdriver.
Move the gear selection lever out of position «P».
C5FP06ZC
C5FP06YC

Downloaded from www.Manualslib.com manuals search engine 347
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
SHIFT LOCK.
NOTE:
The «shift lock»«P».
Unlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed.
Move the gear selection lever out of position
«P».
Unlocking the «SHIFT LOCK»(with an operating fault).
NOTE:It is impossible to unlock the «shift lock»
«Shift lock»
«shift lock»by pressing at «a»with a screwdriver placed in the gear selection
control gate.
Move the gear selection lever out of position
«P».
Engine: RFN
XSARA PICASSO
B2CP3N8C

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
355
C2 AXLE GEOMETRY
Tyres inflated to correct pressures. Vehicle at reference height.
Steering rack locked at mid point (see corresponding operation).
Conditions for checking and adjusting
Vehicle heights at reference height
E1APOBZD
Front height Rear height
L1L2
H1 = R1 – L1 H2 = R2 + L2
H1
= Measurement between the measuring zone underneath the front H2 = Measurement between the measuring zone underneath the rear
subframe and the ground. sill and the ground.
R1= Front wheel radius under load.R2= Rear wheel radius under load.L1= Distance between the wheel axis and the measuring zoneL2= Distance between the wheel axis and the measuring zone
underneath the front subframe. underneath the rear sill.

Downloaded from www.Manualslib.com manuals search engine 359
AXLES
SUSPENSION
STEERING
REAR AXLE
Tightening torques (m.daN).
(25) Rear axle fixing screw: 10 ± 1
(26)Antiroll bar:
(27)Rear axle crossmember:
(28)Rear suspension arm silentblock yoke:
(29)Rear suspension arm silentblock:
(30)Yoke / suspension arm fixing screw:7 ± 0,5
(31)Rear suspension arm:
(32)Stub axle bearing nut: 20 ± 2
(33)Damper:
(34)Damper upper fixing:4,5 ± 0,4
(35) Damper lower fixing: 9,3 ± 0,9
(36)Suspension springs:
(37)Travel stop:
(38)Secondary brake cable guide support:
Private vehicles Antiroll bar
Europe
Diameter (mm)
HFX KFV20,5
(tubular)
8HX 23,5 (tubular)
NFU 25 (solid)
Vehicle entreprise Diameter (mm)
8HX 20,5
(tubular)
CRD vehiclesDiameter (mm)
8HX 20,5
(tubular)
NFU 25,5 (tubular)B3DP09UP
C2

Downloaded from www.Manualslib.com manuals search engine 362
AXLES
SUSPENSION
STEERING
FEATURES OF ELECTRIC POWER STEERING
Engines: HFX KFV NFU 8HX
Steering mechanism
Tightening torques (m.daN.).
(4)
Balljoint fixing on pivot:3,5 ± 0,3
(5)
Steering rod locknut: 5 ± 0,5
(8)
Threaded washer
(9)Stud: 0,8 ± 0,1
(10)
Flat washers
(11)Fixing of mechanism on subframe:8 ± 0,8
Connectors.
(6)
Supply of electric assistance motor
(7)Torque sensor signals
HFX KFV 8HXNFU
Electric motor 60 A 65 A
Steering rack travel2x722x64
Steering ratio45,6/1
Number of rotations of
steering wheel 3,22,8
Inner angle of lock 38° 32°30’
Outer angle of lock 32°24’ 28°42’
B3EP13JD
C2

Downloaded from www.Manualslib.com manuals search engine 364
AXLES
SUSPENSION
STEERING
SPECIAL FEATURES: STEERING
Engines: HFX KFV NFU 8HX
Centring the steering rack
Preliminary operation.
Raise and support the vehicle on a twocolumn lift.
Remove, on the RH side of the steering rack:
Clip
(1).
Clip (2).
Release the steering rack rpotection gaiter.
Setting.
Move the steering to full left hand lock.
Measure the dimension X.
Move the steering to full right hand lock.
Measure the dimension
Y.
Calculate the dimension:
L = (Y – X) : 2.
Refit:
The steering rack rpotection gaiter.
New clips
(1)and (2).
B3EP13UC
B3EP13VD
C2

Downloaded from www.Manualslib.com manuals search engine 365
AXLES
SUSPENSION
STEERING
AXLE GEOMETRY
Conditions for checking and adjusting
Vehicle heights at reference height
Rear height
Fr ont height
L2
L1
Tyres inflated to correct pressures. Vehicle at reference height.
Steering rack locked at mid point (see corresponding operation).
H1 = R1 L1
H1
= Measurement between the measuring zone underneath the front
subframe and the ground.
R1= Front wheel radius under load.L1= Distance between the wheel axis and the measuring zone
underneath the front subframe.
H2 = R2 + L2
H2
= Measurement between the measuring zone underneath the rear
sill and the ground.
R2=Rear wheel radius under load.L2= Distance between the wheel axis and the measuring zone
underneath the rear sill.
E1AP09MD
C3
C3

Downloaded from www.Manualslib.com manuals search engine 368
AXLES
SUSPENSION
STEERING
AXLE GEOMETRY
Conditions for checking and adjusting
Vehicle heights at reference height
Rear height
Fr ont height
L2
L1
Tyres inflated to correct pressures. Vehicle at reference height.
Steering rack locked at mid point (see corresponding operation).
H1 = R1 L1
H1= Measurement between the measuring zone underneath the front
subframe and the ground.
R1= Front wheel radius under load.L1= Distance between the wheel axis and the measuring zone
underneath the front subframe.
H2 = R2 + L2
H2= Measurement between the measuring zone underneath the rear
sill and the ground.
R2=Rear wheel radius under load.L2= Distance between the wheel axis and the measuring zone
underneath the rear sill.
E1AP0AUD
C3 PLURIEL
C3 Pluriel

Downloaded from www.Manualslib.com manuals search engine 375
AXLES
SUSPENSION
STEERING
SUSPENSION
Rear axle
(25)
Rear axle fixing screw: 10 ± 1
(26)
Antiroll bar:
(27)
Rear axle crossmember:
(28)
Rear suspension arm silentblock mounting yoke:
(29)
Rear suspension arm silentblock:
(30)
Suspension arm fixing screw on yoke:7,6 ± 0,5
(31)
Rear suspension arm:
(32)
Stub axle bearing nut : 20 ± 2 greased
(33)
Damper :
(34) Damper upper fixing screw: 4,5 ± 0,4
(35)
Damper lower fixing screw:9,3 ±0,9
(36)
Suspension spring:
(37)
Travel stop:
(38)
Secondary brake cable guide support:
Antiroll bar
EnginesDiameter (mm)
C3
AllTypes25,5
(tubular)
C3 Pluriel 26 (tubular)B3CP09UP
C3 C3 PLURIEL