stop led Citroen XSARA 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 30
GENERAL
CAPACITIES (in litres)
Draining mandhod.
The oil capacities are defined according to the following mandhods.
1/
Vehicle on level surface (in high position, if equipped with hydropneumatic suspension).
2/Engine warm (oil temperature 80°C).
3/ Draining of the oil sump + removal of the cartridge (duration of draining + dripping = 15 min).
4/Refit plug + cartridge.
5/ Engine filling.
6/Engine starting (allowing the cartridge to be filled).
7/ Engine stopped (stationary for 5 min).
ESSENTIAL: Systematically check the oil level using the oil dipstick.

Downloaded from www.Manualslib.com manuals search engine 231
ENGINE
ALL TYPES FILLING AND BLEEDING THE COOLING CIRCUIT
Tools.
[1]
Filling cylinder: 4520T
[2]Adaptor for filling cylinder: 4222T
IMPERATIVE: Respect the safety and cleanliness requirements.
The draining and refilling operations can be carried out using WINN’S or similar coolant fluid replacement
equipment;it is essential to follow the instructions as stated for that equipment.
Filling and bleeding.
Fit the cylinder adaptor [2] 4222T (Picasso,C2,C3)and the filling cylinder [1] 4520T (all types).
Use the coolant to ensure protection between 15°C and 37°C.
Slowly fill the system.
NOTE:Keep the cylinder filled up (visible level).
Close each bleed screw as soon as the coolant flows without air bubbles.
Start the engine :Engine speed
1500 rpm.
Maintain this speed until the first cooling cycle (cooling fans cut in and cut out).
Stop the engine and allow it to cool down.
Remove the filling cylinder
[1] 4520T (all types)and the cylinder adaptor [2] 4222T.
Top up the system to the max. mark, with the engine cold.
Refit the filler cap.
E5AP1GNCB1GP00AC

Downloaded from www.Manualslib.com manuals search engine 289
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH CONTROLS: FEATURES / CHECKS AND ADJUSTMENTS
Engines: KFW NFU 6FZ RFN RFS 8HX 9HZ 9HY WJY RHY RHZ
Refitting.
Place the pedal in the high position (contact at “a”).
Attach the cable yoke on the hook of the clutch pedal.
Fit a new clip
(3).
Fit the endpiece (4)to the bulkhead (fit with G6grease).
Clip the endpiece (5)on the gearbox.
Couple the cable to the lever (1).
Depress the clutch cable several times to lodge the cable in place.
Check that the endpiece (4) is correctly lodged on the bulkhead.
Check the operation of the automatic adjusting system.
After fitting the cable, pull the clutch lever in the inverse direction
(direction F), the lever should
move back when pulled by hand.
Press the clutch pedal very lightly and repeat the same operation. The lever should not move
back.
WARNING:If a system blockage is detected when checking, or if the pedal has been removed,
the pedal position must be adjusted. The correct positioning of the pedal is obtained by the
angular displacement of the stop supports
"a"and "b".
B2BP03CD
XSARA XSARA PICASSO
«PUSH» clutch
«PULL» clutch
B2BP03DD

Downloaded from www.Manualslib.com manuals search engine 342
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Gearbox end.
The automatic gearbox is controlled by a cable.
«c»or «d»Pushbutton.
(1)Control lever with balljoint.
(2)Automatic adjustment (pull out the button to adjust the control, push it in to lock the
adjustment of the control).
(3)Sleeve stop.
(4)Selection control locking clip (5)on the sleeve stop(3).
Engines: KFV RFN
C3 XSARA PICASSO
B2CP3H8CB2CP3N7C
XSARA PICASSOC3

Downloaded from www.Manualslib.com manuals search engine 344
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Gearbox end.
(1)
Control lever.
(2)Automatic adjustment.
(3) Sleeve stop.
The automatic gearbox is controlled by a cable.
Engines: NFU RFN RHZ
XSARA
XSARA