Engine Citroen XSARA PICASSO 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine ENGINE
157
CHECKING AND SETTING THE VALVE TIMING
Engines: HFX KFV NFU
B1EP18TD
Adjusting the fitting tension of the timing belt.
A:Engine:HFX – KFV.
B:
Engine:NFU.
Slacken the nut while maintaining the position of the tensioner roller, with the aid of
a hexagonal spanner at
«a».
Next bring the index
«c»to its adjusting position «a».
The index
«c»should not go beyond the notch «g».
WARNING:The index«c» must not go beyond the notch«g».If it should do this,
restart the timing belt tensioning operation.
Hold the tensioner roller
(7)in this position, with the aid of a hexagonal spanner.
Tighten the tensioner roller fixing nut to :
2 ±0.2 m.daN.(HFX - KFV engines)
2.2 ± 0.2 m.daN.(NFU engine)
IMPERATIVE: The tensioner roller must not rotate during the tightening of its
fixing. If it does, restart the timing belt tensioning operation.
Complete the refitting.
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 158
ENGINE
Tools.
[1]
Flywheel peg: 4507T.A
[2]Camshaft pulley peg: 4507T.B Tool kit 4507T
[3]Square: 4507T.J
[4]Belt tension measuring instrument:4122T
[5]Valve rocker thrust plate :4533T.Z
Checking the timing.
Peg the flywheel, using tool [1].
Peg the camshaft pulley, using tool [2].
Setting the timing.
NOTE:
Remove the sparking plugs, to ease rotation of the crankshaft.
Rotate the engine by means of the crankshaft screw (1).
Peg the camshaft pinion.
Peg the flywheel
Slacken the nut
(2).
Fullt detension the belt by acting on the tensioner roller.
Remove the belt.
IMPERATIVE: Check that the tensioner roller turns freely (no tight spot).
CHECKING AND SETTING THE VALVE TIMING
Engines: KFW NFV

B1EP067CB1EP066CB1EP068C
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 159
CHECKING AND SETTING THE VALVE TIMING
Engines: KFW NFV
Refitting the timing belt.
NOTE:
Check that the pegs [1]and [2]are in place.
WARNING: Respect the direction of fitting of the belt: The arrows "a" indicate the direction of rotation of
the crankshaft.
Position:
The timing belt, belt "b"welltensioned, in the following order:
Crankshaft pinion, camshaft pulley, coolant pump pulley, tensioner roller.
Tool
[5](respect the direction of fitting relative to the valve timing).
Put the tensioner roller in contact with the belt.
Tighten the nut
(2).
Pretensioning the belt.
Place tool [4]on the tensioned part "b"of the belt.
Slacken the screw (2).
Turn the roller (3)in the anticlockwise direction using the drive square, to obtain a value of:44 SEEM units. Tighten the nut (2)to 2 m.daN. Remove tools [1], [2]and [4].
Rotate the crankshaft 4 turnsin the normal direction of rotation.
IMPERATIVE:Never turn the crankshaft backwards.
B1EP06ACB1EP069C
XSARA XSARA PICASSO
ENGINE

Downloaded from www.Manualslib.com manuals search engine 160
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: KFW NFV
Pretensioning the timing belt (continued).
Make sure of the timing setting by refitting the pegs [1]and [2].
Remove the valve cover.
Position the tool
[5](respect the direction of fitting relative to the valve timing).
Adjusting the belt tension.
Place tool [4]on the tensioned part of the belt.
Slacken the nut (2).
Detension the belt, but too much.
Tension the timing belt to obtain a value of:
31 ± 2 SEEM units.
Tighten the nut (2)to 2 m.daN.
Remove tools [1], [2], [4] and [5].
Checking the belt tension.
Rotate the crankshaft 2 turnsin the normal direction of rotation.
Check that it is still possible to peg the following components. Flywheel.
Camshaft.
IMPERATIVE: Repeat the belt tensioning operation if the pegging is not possible.
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine ENGINE
161
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Tools.
[1]
Belt tension measuring instrument: 4122 T.
[2]Flywheel locating peg: 4507 T.A
[3]Camshaft pulley locating peg, exhaust:4533 T.A C2 Tool kit 4507 T
[4]Camshaft pulley locating peg, inlet:4533 T.A C1
[5]Tensioning tool:4707 T.J
Checking the valve timing.
Peg the flywheel using the tool [2].
Peg the exhaust camshaft pulley [3].
Peg the inlet camshaft pulley [4].
Setting the valve timing. Peg the flywheel using the tool [2].
Peg the camshaft pulleys [3] and [4].

B1EP11CCB1EP11BC
XSARA

Downloaded from www.Manualslib.com manuals search engine 162
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Loosen the screw (2), remove the belt.
Loosen the six pulley screws (1)on the hubs(there should be a slight amount of friction between the screws and the pinions).
Check that the rollers (2)and (3)rotate freely.
NOTE:The belt bears three identification marks * (a), (b)and (c), facing its own teeth (1), (52) and (72)respectively.
*
(Identification marks = white paint lines on the back of the belt facing the corresponding teeth).
Refit the belt.
Line up mark (A)on the belt with groove (D)of the pinion (4).
Hold the belt against the pinion (4).
B1EP11ECB1EP11DC
XSARA

Downloaded from www.Manualslib.com manuals search engine ENGINE
163
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Turn the two pulleys (1)clockwise to the end of the slots.
With the belt strip (e)fully tensioned, place the belt over the pulley, first exhaust side, then inlet side, while
ensuring that marks (b)and (c)on the belt are aligned with marks (f)on the pulleys.
Hold the belt in this position, and engage it over the water pump pinion and the tensioner roller.
Fit the tool
[1]on the belt at (e).
Rotate the roller (2) (using tool [5])in an anticlockwise direction, to obtain:63 SEEM units.
Tighten the roller (2)to 2 m.daN.
Tighten the six screws (5)to 1m.daN.
ESSENTIAL: Check that:
The camshaft pulleys (1) are not at the end of the slots (by removing a screw). The markings on the belt are aligned with the markings on the crankshaft and camshaft pulleys.
If not, repeat the setting procedure.
B1EP11GCB1EP11FC
XSARA

Downloaded from www.Manualslib.com manuals search engine 164
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Remove the tools [1], [2], [3] and [4].
Rotate the engine by 4 turnsin the normal direction (do not turn backwards). Peg the flywheel [2].
Loosen the six screws (5), while ensuring there is still a slight amount of friction with the pulley.
Peg the camshaft hubs using pegs [3]and [4].
WARNING: In certain cases, it may be necessary to slightly turn the camshaft using the hub fixing screw.
Fit the tool [1].
Loosen the tensioner roller screw (2).
Rotate the roller (2)(using tool [5])in an anticlockwise direction to obtain:37 SEEM units.
Tighten the tensioner roller screw (2)to 2 m.daN.
Tighten the six pulley screws (1)to 1m.daN.
Remove the tools.
XSARA

Downloaded from www.Manualslib.com manuals search engine ENGINE
165
CHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Tools.
[1]
Flywheel peg :4507T
[2]Camshaft peg: 4533TA.C1
[3]Crankshaft setting peg: ().0194.A
Checks.
Raise and support the vehicle, front wheels hanging.
Disconnect the battery.Remove:
The oil filter. The engine cover.
The upper timing cover
(1).
The sparking plugs, to ease rotation of the engine.
Rotate the engine by means of the crankshaft screw
(never turn the engine backwards).
B1BP2ZJD
C3

Downloaded from www.Manualslib.com manuals search engine 166
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: KFU
B1BP2MBC
Position the tools [3]and [2].
Peg the flywheel, using tool
[1].
NOTE:If the setting is not correct, recommence the operation.
Remove the pegs
[2]and [3].
Refit :
The oil filter.
The timing cover
(1).
The engine cover.
Reconnect the battery.
Lower the vehicle.
Perform the operations that are necessary following a reconnection of the battery.
B1BP2ZTC
C3