Wing Citroen XSARA PICASSO 2004 1.G Owner's Guide

Downloaded from www.Manualslib.com manuals search engine 244
INJECTION
SAFETY REQUIREMENTS: HDi DIRECT INJECTION SYSTEM
Engines: HDi ALL TYPES
CLEANLINESS REQUIREMENTS.
Preliminary operations.
IMPERATIVE: The technician should wear clean overalls.
Before working on the injection system, it may be necessary to clean the apertures of the following sensitive components:(refer to corresponding procedures) Fuel filter.
High pressure fuel pump.
High pressure fuel injection common rail. High pressure fuel pipes
Diesel injector carriers.
IMPERATIVE: After dismantling, immediately block the apertures of the sensitive components with plugs, to avoid the entry of impurities.
Work area.
The work area must be clean and free of clutter.
Components being worked on must be protected from dust contamination.

Downloaded from www.Manualslib.com manuals search engine 245
INJECTION
PROHIBITED OPERATIONS: SIEMENS HDI DIRECT INJECTION SYSTEM
Engines: 8HX 8HW 8HZ
Cleaning.
The use of high pressure cleaners is prohibited.
Do not use compressed air.
Fuel supply circuit.
Required fuel: diesel.
Electric circuit.
Swapping injection ECUs between two vehicles will render it impossible to start either vehicle.
It is forbidden to supply a diesel injector with
12 volts.
High pressure fuel pump.
Do not separate the following components from the high pressure fuel pump (5):
Sealing ring
(a)(no replacement parts).
High pressure outlet connector
(b)(will cause a malfunction).
PS: HDi = High pressure Diesel injection
B1HP1K9C
C2 C3 XSARA

Downloaded from www.Manualslib.com manuals search engine 246
INJECTION
PROHIBITED OPERATIONS: SIEMENS HDI DIRECT INJECTION SYSTEM
Engines: 8HX 8HW 8HZ
Diesel injectors.
WARNING: Diesel and ultrasonic c
leaners are prohibited.
Do not separate the following components from the diesel injector
carrier
(2):
Diesel injector
(f)(no replacement parts).
Electromagnetic element
(c)(no replacement parts).
Do not alter the position of the nut
(d)(malfunction).
Do not separate the connector
(e)from a diesel injector.
It is forbidden to clean the carbon deposits from the diesel injector
nozzle.
B1HP1KACB1HP1KBC
C2 C3 XSARA

Downloaded from www.Manualslib.com manuals search engine 247
INJECTION
PROHIBITED OPERATIONS: DELPHI HDI DIRECT INJECTION SYSTEM
Engines: 8HY 8HV
Cleaning.
The use of high pressure cleaners is prohibited.
Do not use compressed air.
Fuel supply circuit.
Required fuel: diesel.
Electric circuit.
Swapping injection ECUs between two vehicles will render it impossible to start either vehicle.
It is forbidden to supply a diesel injector with
12 volts.
High pressure fuel pump.
Do not separate the following components from the high pressure fuel pump (5):
Sealing ring
(a) (no replacement parts).
High pressure outlet connector
(b)(will cause a malfunction).
PS:HDi = High pressure Diesel injection
B1HP1J6C
C3

Downloaded from www.Manualslib.com manuals search engine 248
INJECTION
PROHIBITED OPERATIONS: DELPHI HDI DIRECT INJECTION SYSTEM
Engines: 8HY 8HV
B1HP1J7CB1HP1J8C
Fuel high pressure injection common rail.
Do not separate the pressure regulator «c»from the injection
common rail (2)(Risk of malfunction).
Diesel injectors.
WARNING:
Diesel and ultrasonic cleaners are prohibited.
Do not separate the following components from the diesel
injector carrier
(3):
Diesel injector (e)(no replacement parts).
Electromagnetic component «d»(no replacement parts).
It is forbidden to clean the carbon deposits from the diesel
injector nozzle..
C3

Downloaded from www.Manualslib.com manuals search engine 249
INJECTION
PROHIBITED OPERATIONS: HDi DIRECT INJECTION SYSTEM
Engines: RHY RHZ
XSARA PICASSO
Cleaning.
The use of high pressure cleaners is prohibited.
Do not use compressed air.
Fuel supply circuit.
Required fuel: diesel.WARNING:Do not use other fuels.
Electric circuit.
Swapping injection ECUs between two vehicles will render it impossible to start either vehicle.
It is forbidden to supply a diesel injector with
12 volts.
High pressure fuel pump.
Do not separate the following components from the high pressure fuel pump (5):
High pressure fuel pump third piston deactivator (3)(no replacement parts).
High pressure fuel regulator (4)(no replacement parts).
Sealing ring (1)(no replacement parts).
High pressure outlet connector (3)(will cause a malfunction).
PS:HDi = High pressure Diesel injection
B1HP12CC

Downloaded from www.Manualslib.com manuals search engine 250
INJECTION
PROHIBITED OPERATIONS: HDi DIRECT INJECTION SYSTEM
Engines: RHY RHZ
XSARA PICASSO
High pressure fuel injection common rail. Do not separate the connectors (7)from the common injection rail (6)(malfunction).
Diesel injectors.
WARNING:Diesel and ultrasonic cleaners are prohibited.
Do not separate the following components from the diesel injector carrier (9):
Diesel injector (8)(no replacement parts).
Electromagnetic element (11)(destruction).
Do not alter the position of the nut (10)(malfunction).
Do not separate the connector (12)from a diesel injector.
It is forbidden to clean the carbon deposits from the diesel injector nozzle.
Identification: Injector carrier
There are two types of diesel injector carrier classed according to fuel flow.
Identification by engraving or paint mark
B1HP12EC
B1HP12DC
B1HP16PC
IMPERATIVE: When replacing a
diesel injector carrier, order a
component of the same class.
(See repair manual)
Identification markings:
«a»:Supplier identification.
«b»:PSA identification number.
«c»:Class identification.
Injector carrier
Class 1
Class 2
Engraving
1
2
Paint mark
Blue
Green
Location
On the upper part of the
coil near to the fuel return
aperture

Downloaded from www.Manualslib.com manuals search engine 253
INJECTION
XSARACHECKING AND SETTING THE DELPHI MECHANICAL INJECTION PUMP
Tools.
[1]
Flywheel locating peg: 7014T.J
[2] H M8 screw: ().0188.E Tool kit C.0188
[3]Injection pump setting peg Ø 6 mm : ().0188.H
After carrying out the necessary dismantling operations on the vehicle, proceed in the following manner:
Remove:
The screws
(6), (7), (9), (10)and (12).
The upper casing (8).
The intermediate casing (11).
WARNING:Refit the screw (6)equipped with a washer.(Thickness 5 mm)
Turn the front RH wheel to turn the engine.(Normal direction of rotation) Bring the camshaft and injection pump pulleys to their setting point.
Position the flywheel peg, using tool [1].(From below the vehicle) Turn the engine until the peg [1]engages in the flywheel.
B1EP12NC
Engine: WJY
B1BP1S9C

Downloaded from www.Manualslib.com manuals search engine 254
INJECTION
CHECKING AND SETTING THE DELPHI MECHANICAL INJECTION PUMP
Engine: WJY (continued)
Peg:
The camshaft hub, using tool [2].
The injection pump hub, using tool [3].
Impossible to peg the camshaft.Reset the valve timing (See page 245).
Possible to peg the camshaft, but not the injection pump.Carry out the following operations:
Loosen the screws of the injection pump hub.
Turn the injection pump hub.
Insert the peg
[3]into the setting hole.
Tighten the screws of the injection pump hub.Tighten to 2,3 ±0,2 m.daN.
ESSENTIAL:If setting the diesel injection pump proves impossible, reset the valve
timing.(See page 251)
Remove:
The tools [1], [2]and [3].
The screw (6)and the washer.
Reassemble the components.
B1EP12WDB1BP1S9C
XSARA

Downloaded from www.Manualslib.com manuals search engine 263
INJECTION
CHECKS: TURBO PRESSURE
Engines: 8HX 8HW
B1BP2NXD
C5FP0F5C
C2 C3
Tools.
[1]Pressure gauge for checking boost pressure: 4073T.A
[2]Sleeve for checking boost pressure: ().0171.F
Checks.IMPERATIVE: Respect the following test conditions:
Engine at operating temperature.
Vehicle in running order. Engine under full load.Preparation.
Remove the clips (1).
Fit the tool [2]in the place of the duct (2).
Couple the sleeve [2]on the pressure gauge [1]using the tube «a».Mode of operation.Position tool [1]in the vehicle.
Start the engine.
Engage first gear, start the vehicle.
Engage the gears up to third gear.
Decelerate to an engine speed of
1000 rpm.
Check the pressure:0,6 ± 0,05 bar (1500 rpm).
Accelerate freely (change from fourth gear to third gear).
Check the pressure:0,9 ± 0,05 bar(between 2500 and 3500 rpm).
Remove tools [1], [2]at «a».
Reposition the tube (2)and tighten the clips (1).