Gearbox Citroen XSARA PICASSO 2004 1.G Service Manual

Downloaded from www.Manualslib.com manuals search engine ENGINE
171
CHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ RFN 2003 # NEW ASSEMBLY2003 #
(6)Crankshaft pinion
(7)Accessories drive pulley
(8)Washer
(9)Screw
The pinion
(6)is fitted as an idler on the crankshaft.
The accessories drive pulley
(7)is immobilised on the crankshaft by a halfmoon keyway and
by the tightening of washer
(8)and screw (9).
A:Pegging on manual gearbox.
B:Pegging on automatic gearbox.
The pegging of the crankshaft is done on the flywheel, or on the converter drive plate
(automatic gearbox).
The pegging hole on the cylinder block
(exhaust end)is calibrated and reinforced.
IMPERATIVE: Never turn the crankshaft with the accessories drive pulley slackened.
IMPERATIVE: Never remove the accessories drive pulley without pegging the crank
shaft and the camshafts.
IMPERATIVE: Always turn the crankshaft in the direction of engine rotation.
B1EP1B9D
B1BP2V2D
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine ENGINE
173
CHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ RFN 2003 #
Checking the setting of the timing (continued).
A:
Pegging on the manual gearbox.
B:Pegging on the automatic gearbox.
Turn the engine by means of the crankshaft pinion screw, to bring it to the pegging position.
Peg the crankshaft, using tool
[2].
Peg the camshaft pulleys, using tool
[3].
NOTE:The pegs [3]should go in without effort.
WARNING:If the pegs go in only with difficulty, repeat the operation for fitting and
tensioning the timing belt
(see corresponding operation).
Refitting.
Remove tools [2]and [3].
Complete the refitting in reverse order to removal.
B1BP2V3D
B1EP1BAC
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine ENGINE
175
CHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ RFN 2003 #
Setting the timing (continued).
A:
Pegging on the manual gearbox.
B:Pegging on the automatic gearbox.
Peg:
The crankshaft, using tool
[2].
The camshaft pulleys
(5)and (6), using tool [1].
Remove:
The screw
(3)of the crankshaft pulley (2).
The lower timing cover
(4)(by moving the engine).
IMPERATIVE: Never remove the crankshaft pulley (2) without pegging the crankshaft
and the camshafts.
Slacken the screw (9)of the tensioner roller (8).
Turn the tensioner roller
(8)(clockwise).
Remove the timing belt
(7).
I
MPERATIVE: Systematically replace the following components: timing belt, exhaust
manifold fixing nuts, timing belt tensioner roller nut.
B1BP2V3DB1EP1BBD
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 280
SPEEDOMETERALL TYPES
An E.E.C. decree of 25 June 1976, regulates the speed displayed by the speedmeter in relation to the actual speed travelled.
This decree stipulates:
The speed indicated by a speedometer must never be lower than the actual vehicle speed.
Between the speed displayed «SD»and the speed travelled «ST», there must always be the following relationship:
ST < SD < 1.10 ST + 4 Kph
Example: For an actual speed of 100 Kphthe speed displayed by the speedometer may be between 100and 114 Kph.
The speed indicated by the speedometer may be influenced by:
The speedometer.
The tyres fitted to the vehicle.
The final drive ratio.
The speedometer drive ratio.
Any of these components can be checked without removing them from the vehicle
(see information note N° 78-85 TT of 19 October 1978).NOTE:Before replacing the speedometer, check the conformity of the following points:
The tyres fitted to the vehicle.
The gearbox final drive ratio.
The speedometer drive ratio.
CLUTCH
GEARBOX
TRANSMISSION

Downloaded from www.Manualslib.com manuals search engine CLUTCH
GEARBOX
TRANSMISSION
281
CLUTCH SPECIFICATIONS C2
Engine type HFX KFV NFU 8HX
Gearbox type Supplier
BVM BVM/BVMP (*)BVM/BVMP (*)BVM/BVMP (*)
MA 5/S MA 5 N/L MA 5 S/L MA 5/0
Mechanism / typeVALEO LUK
Engine type180 CP0 3400 200 P 3900
Bearing supplier / heightSKF 17 mm
Clutch disc11 R 10??
Ø of lining.Ext/Int180/127200/134
Quality of lining408
1.1i 1.4i 1.6i 16V1.4 HDi
(*): BVM = Manual gearbox.
: BVMP = Piloted manual gearbox.

Downloaded from www.Manualslib.com manuals search engine 282
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
C3 C3 PLURIEL
Engine type HFX KFV KFU NFU 8HX 8HW 8HV 8HY
Gearbox type Supplier
MA/5 BE4/5
Mechanism / typeVALEO ? LUK
Engine type180 CPO 3400200 MF
200 P 3900 230 P 4700
3850
Clutch disc11 R 10 X 200 VTB
Ø Garniture.Ext/Int180/127 ? 200/134 228/155
Quality of liningF408
1.1i 1.4i 16V 1.4 HDi1.4 HDi 16V1.4i 1.6i 16V

Downloaded from www.Manualslib.com manuals search engine 283
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS XSARA
Engine type KFW NFU RFN RFS
Gearbox type Supplier
MA/5 MA/5 BE4/5
Mechanism / typeVALEO
Engine type180CPO 3400 200 CPR 3800 230 DNG 4700 215 DT 5250
Clutch disc180 XJF 73 C 200X(D95) 11A12X 230 DNG 4700 215 FD 95
Ø Garniture.Ext/Int180/127 200/137 228/155 215/147
Quality of liningF 408 F 808
1.4i 1.6i 16V2.0i 16V

Downloaded from www.Manualslib.com manuals search engine 284
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
XSARA
Engine type 8HZ WJY RHY RHZ
Gearbox type Supplier
BE4/5
Mechanism / typeLUK
Engine type200 P 4200 200 P 3700 230 P 4700 235 T 5700
Clutch disc215 F (D 93) 22 BX 228 228D
Ø Garniture.Ext/Int200/134 200/134 230/155 235/155
Quality of liningF 408F202
1.4 HDi 1.9 D2.0 HDi

Downloaded from www.Manualslib.com manuals search engine 285
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS XSARA PICASSO
Engine type NFV 6FZ RFN 9HZ 9HY RHY
Gearbox type Supplier
BE4/5
Mechanism / typeVALEO LUK
Engine type200 DNG 3800 230 DNG 4700 215 DT 5250 225 DNG 5100 230 P 4700
Clutch disc200X(D95) 230 DNG 4700 215 FD 95 228
11A12X
Ø Garniture.Ext/Int200/137 228/155 215/147 225/150 230/155
Quality of liningF410 F 808 F 810 DS F408
1.6i 1.4 HDi 16V2.0 HDi1.8i 16V 2.0i 16V

Downloaded from www.Manualslib.com manuals search engine 286
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engines: HFX – KFV – KFU – NFU – 8HX – 8HW – 8HV – 8HY
NOTE:All the clutches are «push»type with hydraulic control.
Description.The declutch control has a declutch fork mounted on a balljoint.(1)The balljoint is screwed into the clutch casing.(2)Declutch fork.(3)Clutch casing.(4)Bearing.(5)Clutch plate.
The clutch control slave cylinder
(7)is fixed by two screws (6)onto the exterior of the clutch casing.
Tightening torques (m.daN).
Fixing of clutch plate / engine flywheel: 2 ± 0,2 Fixing of clutch control slave cylinder / clutch housing:2 ±0,25 Fixing of engine flywheel / crankshaft
Pretightening:1,7 ± 0,1Angular tightening:70° ± 5°
B2BP047CB2BP04QC
C2 C3 C3 PLURIEL