Wheel Citroen XSARA PICASSO 2004 1.G Manual PDF

Downloaded from www.Manualslib.com manuals search engine 368
AXLES
SUSPENSION
STEERING
AXLE GEOMETRY
Conditions for checking and adjusting
Vehicle heights at reference height
Rear height
Fr ont height
L2
L1
Tyres inflated to correct pressures. Vehicle at reference height.
Steering rack locked at mid point (see corresponding operation).
H1 = R1 L1
H1= Measurement between the measuring zone underneath the front
subframe and the ground.
R1= Front wheel radius under load.L1= Distance between the wheel axis and the measuring zone
underneath the front subframe.
H2 = R2 + L2
H2= Measurement between the measuring zone underneath the rear
sill and the ground.
R2=Rear wheel radius under load.L2= Distance between the wheel axis and the measuring zone
underneath the rear sill.
E1AP0AUD
C3 PLURIEL
C3 Pluriel

Downloaded from www.Manualslib.com manuals search engine 369
AXLES
SUSPENSION
STEERING
C3 PLURIEL
AXLE GEOMETR Y
B3CP07SD
Measuring front height Measuring rear height
[1]
Gauge for measuring the wheel radius, 4 bolts, tool 4003T
Z1
= Measuring zone underneath the front subframe.Z2 = Measuring zone underneath the rear sill.
Measure the radius of the front wheel
R1 Calculate dimension H1 = R1 – L1Measure the radius of the rear wheel R2 Calculate dimension H2 = R2 + L2
Value at referenceAll TypesValue at referenceAll Typesheight height
(+ 6 8 mm)L1 = 132,5 mm(+ 10 6 mm)L2 = 47 mm
(*) = CRD: Difficult road conditions.
Definition for a type of vehicle whose axles and suspensions are adapted for driving on rough roads.
Compress the suspension to obtain the calculated values. The height difference between the two axle dimensions should be less than
10 mm.
Checks at reference height

Downloaded from www.Manualslib.com manuals search engine 370
AXLES
SUSPENSION
STEERING
A < B = Positive figure: + = TOEIN
A > B = Negative figure: = TOEOUT
WARNING
AXLE GEOMETRY
Rear axle Front axle
Dissymmetry of lower camber at 0° 18’. Dissymmetry of lower castor at
0° 30’.
Dissymmetry of lower camber at 0° 18’.
Distribute symmetrically, LH / RH wheel, the total tracking value.
All types
Vehicle TrackingCastor Camber Pivot angle
(± 0°18’) (± 0°30’) (± 0°30’)
Adjustable Non adjustable
2 ± 1
0°18’± 0°09’ 3°53’ 0°26’ 11°14’Tracking Camber (± 0°18’)
Non adjustable
5,7 ± 1
0°51’ ± 0°09’ 1°30’
All
Typesmm
0°
B3CP02UC
C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 371
AXLES
SUSPENSION
STEERING
FRONT AXLE
Tightening torques (m.daN).
(1)Nut fixing suspension leg on body: 6,5 ± 0,6
(2)Suspension leg:
(3)Antiroll bar link rod upper balljoint: 3,2 ± 0,3
(4)Suspension leg pivot: 5,4 ± 0,5
(5)Antiroll bar link rod lower balljoint: 3,2 ± 0,3
(6)Antiroll bar bearing fixing on subframe:8 ± 0,8
(7) Hub nut: 24,5 ± 0,5
(8)Wheel bolt:9 ±1
(9)Subframe to bodyshell fixing screw:10 ± 1
(10)Antiroll bar:
(11) Pivot lower balljoint fixing on lower arm: 5,5 ± 0,5
(12)Pivot lower balljoint fixing: 4 ± 0,4
(13)Lower arm front and rear mounting fixing:14 ±0,4
(14)Stabiliser bar screw: 6,6 ± 0,7
(15)Steering balljoint fixing:3,5 ± 0,3
Antiroll bar
Diameter (mm) Colour
HFX KFV
C3KFU NFU 8HX19Blue
8HW 8HV 8HY
C3
Pluriel KFV NFU 8HX 20 Green
B3CP07RP
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 373
AXLES
SUSPENSION
STEERING
SUSPENSION
Front axle
(1)
Nut fixing suspension leg on body: 6,5 ± 0,6
(2)Damper:
(3)Antiroll bar link rod upper balljoint: 3,2 ± 0,3
(4)Suspension leg pivot: 5,4 ± 0,5
(5) Antiroll bar link rod lower balljoint:3,2 ± 0,3
(6)Antiroll bar bearing fixing on subframe: 8 ± 0,8
(7)Hub nut: 24,5 ± 0,5
(8) Wheel bolt:9 ± 1
(9) Subframe to bodyshell fixing screw: 10 ± 1
(10)Antiroll bar:
(11)Pivot lower balljoint fixing on lower arm:5,5 ± 0,5
(12)Pivot lower balljoint fixing: 4 ± 0,4
(13)Lower arm front and rear mounting fixing: 14 ± 0,4
(14) Stabiliser bar screw: 6,6 ± 0,7
(15) Steering balljoint fixing: 3,5 ± 0,3
Antiroll bar
Engines Diameter (mm) Colour
C3
AllTypes19 Blue
C3 Pluriel 20 Green
Pivot
Engines Diameter of bearing Type
C3
C3 Pluriel AllTypes 72 In U
(cast iron)B3CP07RP
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 376
AXLES
SUSPENSION
STEERING
FEATURES OF ELECTRIC POWER STEERING
Engines: HFX KFV KFU NFU 8HX 8HW 8HV 8HY
Steering column
Tightening torques m.daN.
(1)
Steering wheel fixing:2 ±0,3
(2)
Steering column fixing on support:2,2 ± 0,5
(3)
Steering cardan fixing: 2,2 ± 0,2Identification.
Identified by the colour of the ring at «a».
Left hand drive
:BLUE ring.
Right hand drive
: WHITE ring.
B3EP13GDB3EP13HC
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 377
AXLES
SUSPENSION
STEERING
FEATURES OF ELECTRIC POWER STEERING
Engines: HFX KFV KFU NFU 8HX 8HW 8HV 8HY
Steering mechanism
Tightening torques m.daN.
(4)
Balljoint fixing on pivot: 3,5 ± 0,3
(5)
Steering rod locknut: 5 ± 0,5
(8)
Threaded washer
(9) Stud: 0,8 ± 0,1
(10)
Flat washers
(11)Fixing of mechanism on subframe:8 ±0,8
Connectors.
(6)
Supply of electric assistance motor
(7) Torque sensor signals
HFX KFV 8HX 8HWKFV (BVA)
NFU 8HY 8HV
Electric motor 60 A 65 A
Steering rack travel2x72 2x64
Steering ratio45,6/1
Number of rotations
3,22,8
of steering wheel
Inner angle of lock 38° 32°30’
Outer angle of lock 32°24’ 28°42’
B3EP13JD
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 378
AXLES
SUSPENSION
STEERING
FEATURES OF ELECTRIC POWER STEERING
Engines: HFX KFV KFU NFU 8HX 8HW 8HV 8HY
Steering assistance
Supplier:KOYO.
The steering assistance is rpovided by the assistance motor
(12), controlled
by the ECU.
Power delivered to the assistance motor
(12)depends on:
Speed of the vehicle.
Torque applied on the steering wheel.
Electric powerassisted steering ECU.
Only one ECU version, whatever the enginetype.
The electric power steering ECU is linked to the following connectors:

(6)Assistance motor supply.
(13)Electric power steering ECU supply.
(14) Control signals.
After changing the electric power steering ECU, it is necessary to
perform a configuration
(see corresponding operation).
B3EP13KCB3EP13LC
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 380
AXLES
SUSPENSION
STEERING
XSARA AXLE GEOMETRY
Front and rear measuring points
XSARA ALL TYPES N°RPO 8667 #
Front heightRear height
H1= Dimension between the centre of the front suspension arm mounting and the ground.H2= Dimension between the contact face of the rear mounting and the ground.R1= Front wheel radius under load.R2= Rear wheel radius under load.L1= Distance between the centre of the wheel and the centre of the front suspension arm mounting.L2= Distance between the centre of the wheel and the contact face of the rear mounting on the bodyshell.
B3CP06ZD

Downloaded from www.Manualslib.com manuals search engine 381
AXLES
SUSPENSION
STEERING
Front axle Rear axle
AXLE GEOMETRY
Reference heights
: 4300T N°RPO 9429
# Tools. [1] Gauge for measuring the radius of wheels with 4 bolts
Setting the reference height.
Front
Fr ont
Measure the dimension «R1».
Calculate the dim.
H1 = R1 L1.Measure the dimension
«R2».
Calculate the dim.
H2 = R2 + L2.
Compress the suspension until the values
(H1)and (H2)are obtained.
NOTE:The difference in height between the two sides should be less than10 mm.
XSARA
Reference heights
(in mm)115,5
90,575,5 73
8388 103 Engines2.0i 16V
(RFS)All engines (except
2.0 i 16V and CRD)All CRD
engines 2.0i 16V
(RFS)All Saloon (except
2.0i 16V and CRD)EstateAll CRD
engines
B3CP04AD