check engine light DACIA LOGAN 2011 User Guide
Page 83 of 238
Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.9
ENG_UD32518_3
levier de vitesses (X52 - Dacia)
ENG_NU_993-5_X52_Dacia_2
Selecting reverse gear(vehicle stationary)
Vehicles with manual gearbox: refer
to the grid on the gear lever knob 1.
Vehicles with a sequential gear-
box: refer to the information under
“Sequential gearbox” in Section 2.
The reversing light(s) will come on as
soon as reverse gear is selected (igni-
tion on).
GEAR LEVER
An impact to the under-
side of the vehicle while
manoeuvring (e.g.: stri-
king a post, raised kerb or
other street furniture) may result in
damage to the vehicle (e.g.: defor-
mation of an axle).
To prevent any risk of accident,
have your vehicle checked by an
approved dealer.
1
Page 86 of 238
Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.12
ENG_UD35136_3
Conseils de conduite, ECO conduite (X52 - Dacia)
ENG_NU_993-5_X52_Dacia_2
DRIVING ADVICE, ECO-DRIVING (3/4)
Driving advice, Eco-driving
Behaviour
– Drive carefully for the first few miles
until the engine reaches its normal
operating temperature, rather than
let it warm up while the vehicle is sta-
tionary.
– Speed is expensive.
– Sporty driving uses a lot of fuel: drive with a light right foot.
– Do not overrev the engine in the in- termediate gears.
You should always use the highest gear possible.
– Avoid sudden acceleration.
– Brake as little as possible. If you an-ticipate an obstacle or bend in ad-
vance, you may then simply release
the accelerator pedal.
– Do not try to maintain the same speed up a hill, accelerate no more
than you would on the level. Keep
your foot in the same position on the
accelerator pedal.
– Double declutching and accelerating before switching off are unnecessary
in modern vehicles.
– Bad weather, flooded roads:
Do not drive through
floods if the water is
above the lower edge of
the wheel rims.
Obstructions to the driver
On the driver’s side, only
use mats suitable for the
vehicle, attached with the
pre-fitted components, and check
the fitting regularly. Do not lay one
mat on top of another.
There is a risk of wedging the
pedals
Page 88 of 238
Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.14
ENG_UD34407_2
Conseils entretien et antipollution (X98 - X87 - X07 - Renault)
ENG_NU_993-5_X52_Dacia_2
MAINTENANCE AND ANTIPOLLUTION ADVICE
Your vehicle complies with criteria for
recycling and recovering vehicles at the
end of their service life which will come
into force in 2015.
Some parts of your vehicle have there-
fore been designed to facilitate future
recycling.
These parts are easy to remove so
that they can be recovered and reproc-
essed by recycling companies.
By virtue of its design, moderate fuel
consumption and initial settings, your
vehicle also conforms to current anti-
pollution regulations. The manufac-
turer is actively striving to reduce pol-
lutant exhaust gas emissions and to
save energy. But the fuel consumption
of your vehicle and the level of pollutant
exhaust gas emissions are also your
responsibility. Ensure that it is main-
tained and used correctly.
Maintenance
It is important to remember that fai-
lure to respect antipollution regulations
could lead to legal action being taken
against the vehicle owner. In addition, replacing engine, fuel
supply system and exhaust compo-
nents with parts other than those origi-
nally recommended by the manufactu-
rer may alter your vehicle so that it no
longer complies with antipollution regu-
lations.
Have your vehicle adjusted and
checked by an approved Dealer, in ac-
cordance with the instructions given in
your maintenance schedule: they will
have all the equipment necessary for
ensuring that your vehicle is maintained
to its original standard.
Engine adjustments
– Spark plugs:
for optimum condi-
tions of use, output and performance
the specifications laid down by our
Design Department must be strictly
applied.
If the spark plugs have to be changed, use the make, type and gap specified
for your vehicle’s engine. Contact an
authorised dealer for this.
– Air filter: a choked element will reduce efficiency. It must be re-
placed.
– Ignition and idle speed: no adjust-
ment is needed.
Exhaust gas monitoring
system
The exhaust gas monitoring system will
detect any operating faults in the vehi-
cle’s antipollution system.
If this system malfunctions, toxic sub-
stances may be released into the at-
mosphere or damage may occur.
ÄThis warning light on the in-
strument panel will indicate if
there are any faults in the system:
This lights up when the ignition is
switched on and goes out when the
engine is started.
– If it lights up continuously, consult an approved Dealer as soon as pos-
sible;
– if it flashes, reduce the engine speed until the light stops flashing. Contact
your approved dealer as soon as
possible.
Page 90 of 238
Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.16
ENG_UD34528_1
Avertisseur de perte de pression des pneumatiques (X52 - Dacia)
ENG_NU_993-5_X52_Dacia_2
TYRE PRESSURE LOSS WARNING (1/3)
If fitted on the vehicle, while driving, this
system notifies the driver if one or more
tyres lose pressure.
Operating principle
Each wheel (except for the emergency
spare wheel) has a sensor in the infla-
tion valve which periodically measures
the tyre pressure while driving.
Warning light
1 comes on to
notify the driver if the pressure is too
low.
Resetting the standard level
for the tyre pressures
This should be done:
– when the standard tyre pressure needs to be changed to adapt to
usage conditions (empty, carrying a
load, motorway driving, etc.);
– after changing a wheel.
It should always be done after checking
the tyre pressure of all four tyres when
cold.
Tyre pressures must correspond to the
current usage of the vehicle (empty,
carrying a load, motorway driving, etc.).
This function is an addi-
tional driving aid.
However, the function does
not take the place of the
driver. It cannot, therefore, under
any circumstances replace the vig-
ilance or the responsibility of the
driver.
Check the tyre pressures, including
the emergency spare wheel, once a
month.
1
Page 91 of 238
Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.17
ENG_UD34528_1
Avertisseur de perte de pression des pneumatiques (X52 - Dacia)
ENG_NU_993-5_X52_Dacia_2
Note:
The standard tyre pressure cannot be
less than that recommended and indi-
cated on the door frame.
Display
Display 2 on the instrument panel in-
forms you of any tyre pressure faults
(flat tyre, punctured tyre, etc.).
Check tyre pressure
The warning light
comes on (not
flashing). This indicates that at least
one tyre is flat.
Check and, if necessary, readjust the
pressures of the four wheels when cold.
The warning light
goes off after a
few minutes’ driving.
Puncture
The warning light and the red
warning light
Ò light up on the in-
strument panel, alongside a beep.
This indicates that at least one wheel
is punctured or severely underinflated.
Replace it or contact an authorised
dealer if it is punctured. Top up the tyre
pressure if the wheel is deflated.
TYRE PRESSURE LOSS WARNING (2/3)
With the engine stopped:
– repeatedly press the button 3 to
select “SEt tP” on the display 2;
– press and hold (around 3 seconds) button 3 to start initialisation. “SEt tP”
flashes then comes on steady. When
“SEt tP” disappears, the standard
tyre pressure is saved.
Reinitialisation is carried out after a few
minutes’ driving.
The sudden loss of pressure in a
tyre (burst tyre, etc.) cannot be de-
tected by the system.
2
3
The red warning light Ò
requires you to stop imme-
diately, for your own safety,
as soon as traffic conditions allow.
Page 92 of 238
Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.18
ENG_UD34528_1
Avertisseur de perte de pression des pneumatiques (X52 - Dacia)
ENG_NU_993-5_X52_Dacia_2
Check tyre sensors
The warning light flashes for
several seconds, then stays on, along
with the orange warning light
Ò.
This indicates that the sensor on at
least one wheel is missing or faulty.
TYRE PRESSURE LOSS WARNING (3/3)
Readjustment of tyre
pressures
The tyre pressures must be adjusted
when cold (please refer to the label lo-
cated on the edge of the driver’s door).
If tyre pressures cannot be checked
when the tyres are cold, the recom-
mended pressures should be increased
by 0.2 to 0.3 bar (3 PSI).
Never deflate a hot tyre.
Replacing wheels/tyres
This system requires specific equip-
ment (wheels, tyres, hubcaps, etc.).
Contact an approved Dealer to fit new
tyres and to find out about available ac-
cessories compatible with the system
and available from your dealer net-
work: the use of any other accessory
could affect the correct operation of the
system or damage a sensor.
Emergency spare wheel
If the vehicle is equipped with an emer-
gency spare wheel, it will not have a
sensor.
When fitted to the vehicle, the warn-
ing light
and the orange warning
light
Ò are displayed on the instru-
ment panel.
Inflation kit
Because the valves are specially de-
signed, only use equipment approved
by the approved network.
Page 112 of 238
Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.38
ENG_UD34964_1
Boîte de vitesses robotisée (X52 - Dacia)
ENG_NU_993-5_X52_Dacia_2
Towing a vehicle with a
sequential gearbox
If the gearbox is stuck in a gear:
– switch on the ignition,
– select neutral,
– check that the gearbox is in neutral,
– turn off the ignition.
If you cannot find neutral you must tow
the vehicle with the front wheels raised.
The vehicle should always be towed
with the ignition switched off.
SEQUENTIAL GEARBOX (6/6)
Operating faults – When driving, if the warning light 5
appears on the instrument panel dis-
play, this indicates a fault.
Consult an approved dealer.
– If the warning light 5 and the orange
warning light
Ò come on together
on the instrument panel while you
are driving, drive carefully to an au-
thorised dealer as soon as possible.
Failure to follow this recommendation
risks damaging your vehicle.
5
Page 150 of 238
Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
4.2
ENG_UD26967_1
Capot moteur (X52 - Dacia)
ENG_NU_993-5_X52_Dacia_4
BONNET
To open the bonnet, pull the handle 1.
Unlocking the bonnet catch
To unlock, gently lift the bonnet and
push tab 2 in the direction of arrow A to
release the catch 3.
Opening the bonnetLift the bonnet; you will need to guide it
as it is held by a strut 4.
Closing the bonnetCheck that nothing has been left in the
engine compartment.
To close the bonnet again, hold the
bonnet in the middle and lower it to
30 cm above the closed position, then
release it. It will latch automatically
under its own weight.
The engine may be hot
during operations in close
proximity. In addition, the
engine cooling fan may
come on at any moment.
Risk of injury.In the event of even a slight
impact involving the radia-
tor grille or bonnet, have
the bonnet lock checked by
an approved Dealer as soon as pos-
sible.
Do not press down on the
bonnet: there is a risk that
the bonnet may accidentally
close.
Make sure nothing is left
in the engine compartment
(cloth, tools, etc.).
These may damage the
engine or cause a fire.
Ensure that the bonnet is
properly locked.
Ensure that nothing is pre-
venting locking (grit, cloths,
etc.).
1
2
4
3
A
When working in the engine
compartment, ensure that
the windscreen wiper stalk
is in the park position.
Risk of injury.
Page 155 of 238
Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
4.7
ENG_UD32521_2
Niveaux / Filtres (X52 - Dacia)
ENG_NU_993-5_X52_Dacia_4
LEVELS (1/4)
Brake fluid level
This should be checked frequently,
and immediately if you notice even the
slightest loss in braking efficiency.
The level should be read with the engine
switched off and on level ground. Level
It is normal for the level to drop as the
brake shoes become worn, but it must
never drop lower than the “MINI” warn-
ing line shown on brake fluid reser-
voir 1.
If you wish to check the disc and drum
wear yourself, you should obtain the
document explaining the checking pro-
cedure from the approved dealer net-
work or from the manufacturer’s web
site.
The engine may be hot
during operations in close
proximity. In addition, the
engine cooling fan may
come on at any moment.
Risk of injury.
Consult your approved dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
Topping up
After any operation on the hydraulic cir-
cuit, a specialist must replace the fluid.
Only use fluids approved by the
Technical Department and which have
been taken from a sealed container.
Replacement intervals
Refer to the Maintenance Document for
your vehicle.
1
Page 162 of 238
Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
4.14
ENG_UD26811_2
Entretien de la carrosserie (peinture mate) (X44 - X77 - J77 - X85 - \
B90 - X61 - TEST - X77 ph2 - X95 - B95 - D95 - K95 - J95 - R95 - L90 Ph2 - F90 Ph2 - R90 Ph2 - X62
ENG_NU_993-5_X52_Dacia_4
Respect local regulations about wash-
ing vehicles (e.g. do not wash your ve-
hicle on a public highway).
Observe the vehicle stopping distances
when driving on gravelled surfaces to
prevent paint damage.
Repair, or have repaired quickly, areas
where the paint has been damaged, to
prevent corrosion spreading.
Remember to visit the body shop pe-
riodically in order to maintain your
anti-corrosion warranty. Refer to the
Maintenance Document.
If it is necessary to clean mechani-
cal components, hinges, etc., spray
them with products approved by our
Technical Department to protect them
after they have been cleaned.
BODYWORK MAINTENANCE (2/2)
We have selected special products
to care for your vehicle and you can
obtain these from the manufactur-
er’s accessory outlets.
Using a roller type car wash
Return the windscreen wiper stalk to
the Park position (refer to the informa-
tion on the “Windscreen washer, wiper”
in Section 1). Check the mounting of
external accessories, additional lights
and mirrors, and ensure that the wiper
blades are secured with adhesive tape.
Remove the radio aerial mast if your
vehicle is fitted with this equipment.
Remember to remove the tape and refit
the antenna after washing.
Cleaning the headlights
As the headlights are made of plastic
“glass”, use a soft cloth or cotton wool
to clean them. If this does not clean
them properly, moisten the cloth with
soapy water, then wipe clean with a soft
damp cloth or cotton wool.
Finally, carefully dry off with a soft dry
cloth.
Cleaning products containing alco-
hol must not be used.
Vehicles with a matte paint
finish
This type of paint requires certain pre-
cautions.
Do not do the following
– use wax-based products (polishing);
– rub hard;
– wash the vehicle in a roller-type car
wash;
– wash the vehicle using a high-pres-
sure device;
– attach stickers to the paintwork (risk
of leaving marks).
You should do the following
Wash the vehicle by hand using plenty
of water, using a soft cloth or a gentle
sponge.