check engine DACIA SOLENZA 2004 User Guide

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 29
Dismounting – Remounting
The over-he ight X must be between 0.02
mm and 0.09 mm.
Place the jackets in such way that :
-the difference between two joint jackets
to be maximum 0.05 mm;
- the over-height to be in ascending order
between cylinders 1 and 4;
- in case of an incorrect over-height, check
the over-height by m eans of a new kit of jack-
ets, i n order to see i f t he c ause i s the block or
the cylinders jacket or check the theoretical size
values of the block and of the jackets. When over-height is correctly obtained, per-
form the A, B, C, D assembly then mark with
numbers jackets, pistons and the bol ts from 1
to 4 (no.1 towards flywheel) so that the corre-
s pondence with the corresponding connecting
rods may be achieved.
Pistons bolts mounting
The pistons bolts are fixed in connecting rods
and free in pistons. Mount the pistons bolts by means of the
MOT 574-22 that is containing:
- a support for piston ( S);
- an extracting mandrel ( M);
- the piston supporting bushings (B);
- the bolts for mounting ( A) provided with
their centering guides (C ). Use an electric plate of
1500 W (electric
oven) for connecting rods heating. Place the connecting rods on the electric
plate so that connecting rod end surfaces are
in contact with the heating plate.
Check if the pistons bolts are freely gliding
in the new corresponding pistons. Mount the piston bolt E on the mounting
bolt A.
Sc rew the centering guide C till end and
then unscrew it for a quarter of turn.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 30
The arrow marked on the piston head must
be oriented towards engine flywheel. The c onnecting rods ha ve no mounting
direction, but the ha lf-bearings spurs are to
be positioned on the same part. In order to assemble the piston and the
connecting rod, proceed as follows: -place the bushing B 13 on the support
and attach the piston (with the arrow oriented
upwards) on the bushing;
Dismounting – Remounting
- lubricate the centering guide and the
piston bolt with engine oil;
- check t he free gliding of the piston
bolt and the piston positioning.
When the connecting rod end is reaching
the necessary temperature (about 250 °C),
proceed to the ra pid of the piston bolt, as
follows: -introduce the centering guide in the
piston; - position the connecting rod i n the
piston;
-press till end the piston bold.
Check if the pi ston bolt is remaining re -
tired as against the piston outer diameter for
each of the connecting rod position in the pis-
ton.
Rings mounting
Mount the rings on the pi ston in the
following sequence: -
oiling ring ( 3);
-s ealing ri ng (2) w ith the mark “TOP”
upwards; -compression ri ng (1) with t he mark
“TOP” upward. The compression and sealing rings are to be
mounted with the slots disposed at 90° against
de bolt’s axle and displaced between them with
180°. The oiling ring is to be mounted with the
slot oriented at 45° against the bolt’s a xle.
The rings slots being adjusted, shall never be
reworked.
Lubricate the pistons with engine oil.
M ount the assemblies “connecting rod-
piston-rings” in the cylinder’s jackets, by means
of the mounting bushing. Mount the sealing gaskets on the cylinder
jackets.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 31
Mount the assembly i n the bl ock, as per
previous established sequence and check and
ensure that a 0.1 mm gauge is passing be-
tween jackets.
Dismounting – Remounting
MOT 484
Block the jackets by means of the device
MOT 484 or the clamps MOT 588.
M ount the base bearing on the cylinders
block. Hal-bearing lining that are mounted on
casing are provided with oiling holes.
The beari ngs lining are matching with the
crankshaft in two classes, as follows: Mount connecting rod bearings (connecting
rod bearings are the same) Lubricate the cranckpin and the bearings.
Mount the crankshaft and the axial bearings.
Mount the bearings caps. On the no.1 cap
(area K) apply a layer of LOCTITE 518, be-
tween 0.6 and 1 mm thick.
Tighten the bearings caps to a required mo-
ment of 2.5 daNm then to an a ngle of 43° ± 6°.
Check the axial clearance of the crankshaft,
which must be between:
*0.045 and 0.852 with wear;
* 0.045 and 0.252 without wear.
Marking on bearing
Red
Bl ue
Marking on crankshaft
A
B
Ide nt i dfi cation of m atching c lasses on
crankshaft i s performed by m arking on t he
balance-weight of bearing number 5. Marking example on crankshaft:
A AB AB
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 32
The axial bearings may have the following
thickness: 2.80, 2.85, 2.90, 295 mm.
M ount the connecting rods caps and
tighten to the required moment of 4.2 daNm.
Check:
-connecting rods lateral clearance;
- assembly rotation.
Mount: -gear and driving chain of the oil pump;
- oil pump (check the existence of the
centering bushings) and tighten the screws to
the required moment of 2.5 daNm;
Dismounting – Remounting
MOT 550
- the crankshaft closing casing; the
sealing is performed using LOCTITE 518 (
the layer H must be 0.6 – 1 mm thick);
- sealing gasket from crankshaft clos-
ing casing (lubricated with oil) by means of
the MOT 550 device;
-crankshaft sealing gasket towards fly-
wheel (at no. 1 bearing) by means of the MOT
1129-01 device. Lubricate the sealing gasket external part
and lip with engine oil.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 41
DISMOUNTIN G
Drain the oil from the engine.
Dismount :
- lower casing (see chapter 10”Lower casing on vehicle”).
Dismount the oil pump attachmen t screws on casing.
Dismount the drive chain from the oil pump gear.
Dismount the oil pump cap.
Check the gears clearance in the oil pump (see chapter 10” Engine assembly”)
REMOU NT I NG
Perform the dismounting operations in the reverse order;
Fill up engine with oil
Check the oil pressure at 80 °C:
At idling 1 bar;
At 4000 rot/min 3 bar. Oil pump attachment screws 2.5
Oil pump cap attachment screws 1

TIGHTENING MOMENTS (daNm)
O
il pump
vnx.su

ENGINE E7J-26211
11 - 5
DISTRIBUTION SYSTEM
MOT 484
Cylinder head gasket
Mount the MOT 484 device or MOT
588 clamps for jackets maintenance.
Check the cylinder head smoothness using
a lineal a nd a set of templates. The maximal admissible deformation: 0.05
mm. The cylinder head is not to be rectified!REMOU NT I NG
Clean the gasket-seating surface of the cyl-
inder head.
Mount the cylinder head with a new gasket.
Perform the dismounting operation s in the re-
verse order.
Tighten the cylinder head observing the cyl-
inder head tightening method described in chap-
ter 10 “Dismounting-Remounting” .
Mount the distribution belt ( see chapter 11
”Distribution belt”).
Adjust the tilters.
Perform the cooling circuit filling and purging
(see chapter 19 “ Filling and Purging” ).
REMARK:
At each operation implying battery dis-
mounting,
when reconnecting it, introduce the radio
code t hat is written on the vehicle-purchas-
ing invoice.
vnx.su

ENGINE E7J-26212
12 - 2
F UEL M IXTURE
DENOMINATION PARTICU LARITIES
UCE injection SIEMENS - Connector with 90 ways
In jection system Sequential multi-point
I gnition Static with double coil PINI R (W)
I gnition control led by
RA- C0,52
ΩΩΩΩ

± 10%

































UCE in
jectionRB-C0,52
ΩΩΩΩ

± 10%
R 1 -47,2 KΩΩΩΩ ±
10%
R
2-37,2 KΩΩ ΩΩ ±
10%
Characteristics
Detonation sensor Sagem – piezo-electric type
Tightening moment = 2 daNm.
RPM sensor ELECTRICFIL or SIEMENS
R = 200………….270 Ù
Spa rk plugs SAGEM – Type RFC 52 LZ
Ti ghtening moment = 2.5 –3 daNm
Fuel filter For de-pollution norm 1504
Mounted under the vehicle in front the fuel tank.
Replacement at every scheduled checking
For EURO 00 and EURO 96;
Insi de the fue l tank, attached on the fuel pump assembly.
Do not replace it separately.
Feeding pump Immersed in the fuel tank
For de-pol lution norm 1504:
- Flow: 1.3 l/min. Pressure: 3 bars at 12 V ten sion.
For EURO 00 and EURO 96:
- Pressure: 3.5 bars at 12 V tension.
Pressure regulator For de-pollution norm 1504:
Regulator attached on the injection ramp.
Adjusted pressure : 3 ± 0.2 b ars at zero depression
2.5± 0.2 bars at 500 mbars depression
For EURO 00 and EURO 96:
Mounted inside the fuel tank on the fuel pump assembly.
Adjusted pressure : 3.5 bars
Electro-magnetic Injectors SIEMEN S
R = 14.5 Ù ± 5 % AT 20 º C
Supply + 12V
Step by step engine R
A-D = 53 Ù 10% at 25º C
R
B- C = 53 Ù 10% at 25 ºC
vnx.su

MOTEUR E7J-26213
FUEL SUPPLY
13 - 3
Pump capacity
1
PUMP CAPACITY CHECKING
SPECIAL TOOLS
Pliers for “CLICK” collars.
IMPORTANT
Duri ng this operation, it is obligatory :
- not - sm oki ng a nd not bri ngi ng
incandescent obj ects at the working pl ace; - protect against petrol splashing due
to residual pressure remained in piping
during their dismounting.
VEHICLES WITH FUEL RETURN
The checking of the fuel pump capacity is
recommended to be performed by t he fue l
return hose connected on the level transmitter -
pump assembly .
Disconnect the fuel return pipe ( 1).
Connect on the pipe a hose, one extremity
being introduced in a calibrated vessel, from 0
to 2000 ml. VE HIC
LES WITHOUT FUEL
RETURN
Disconnect the supply pipe from the fuel
electric pump assembly .
Connect on the pipe a hose, one extremity
being introduced in a calibrated vessel from 0
to 2000 ml.
Start the fuel electric pump by bridging the
3 and 5 terminals of the fuel pump H relay
(placed in the fuse and relays box from engine
compartment).
The pump output must be minimum 1.3 l /
min at 12 V.
If the output is not correct, check the pump
s upply voltage (capacity i s decreasing by
approximate 10% for a voltage drop of 1 V).
vnx.su

ENGINE E7J - 26214
14 - 2
ANTI-POLLUTION
Pet rol vapors re-aspiration
OPERATING PRINCIPLE
The communication of the t ank with t he
atmosphere is done through the carbon can. The petrol vapors are retained when they are
passing through the active carbon from the carbon
can. By means of a purging valve controlled by a
RCO signal issued by UCE injection, the petrol
vapors are re-aspired through piping by the intake
manifold.
The flow section of the purging valve is
variable, subject to the balance given by the
magnetic field created by supplying the purging
valve coil and the power of the spring ensuring
the valve closing.
RE-ASPIRATION CONDITIONS
The can-purging valve is controlled by pin
4 of the UCE injection, in the moment when:
-w ater tempera ture > 20 ° C;
- air temperature > 10 ° C;
- engine is running over a certain im-
posed charge; -valve potentiometer is not in the posi-
tion acceleration pedal not pressed.
By using the CLIP tester, it is possible the
reading of the RCO value (opening cyclic
ratio).
The purging valve is closed for a value
smaller than 0.7%. OPERATION CHECKING OF THE
CAN PURGING VALVE
A defective operation of the petrol vapors
re-aspiration system, may lead to an unstable
idling or even to the engine stopping. First of all, check:
-circuit conformity (see the operating
diagram)
-piping condition between the can and
the fuel tank (sealing, circuit clogging).
The (B) piping coming from the tank shall
be clogged.
Connect a manometer (-3…+3 bar) at the
(M) connection for communication with the
atmosphere and check at idling if there is
depression. Is there depression?
YES – Set conta ct off. Usi ng a
vacuum pump, apply a 500 - mbar depression
at the (A ) piping connection of t he purging
valve. The value of the red depression must
not have a variation more than 10 mbar
wi thin 10 seconds.
vnx.su

ENGINE E7J - 26214
14 - 3
ANTI-POLLUTION
Pet rol vapors re-aspiration
1
4
3
2
Petrol vapors re-aspiration
If the pressure is varying more than 10
mbar, then the purging valve is defective and
the carbon can assembly is to be replaced. NO – When conditions for purging valve
controlling are accomplished and this one is
not opening, check its controlling electri c
circuit (between UCE injection pin 4 and
purging valve), from point of view continuity
or short-circuit. The RCO value of the signal received by
the purging value from the computer, may be
red by means of the CLIP tester in PR 023.
The minimal value is 0.7 % (corresponding
to the closing position of the purging valve).
LOCA TION – DISMOUNTING
The carbon can assembly ( 1) with
incorporated purging valve, is placed on the
front right wing lining. Disconnec t the piping ( 2) coming from the
tank and piping ( 3) to the engine.
Di sconnect the electric connector ( 4) of
the purging valve. Remove the can from the attachment
support. Perform the dismounting operations
in
the reverse order REMOUNTING
vnx.su