Signal DACIA SUPERNOVA 2004 Owner's Manual

82A
HORN - ENGINE IMMOBILISER
82A - 37
A
LP8. TURNING LIGHTS DO NOT SWITCH ON AT THE BLOCKING /
UNLOCKING OF THE DOORS
RECOMMENDATION Check the absence of the failures with the CLIP tester.
If there are failures, fix them first.
Check if the synchronisatio n of the RF remote control and the E.C.U. decoder has been performed .
Are the turning lights functioning normally at the activation of the signalling switch ?
Check the continuity and the isolation related to
the ground and the +12 V of the electric layout:
E.C.U. decoder FLASH relay
Pin B3 pole 2
Is it correct?
Repair the signalli ng system.
Check t he fuse F03 and F04.
Fix the electric layout.
Check the fuse F15 ( up to 01.06.2001) or
F 07 (after 01.06.2001).
Is it good?Replace the fuse.
Disconnect the FLASH relay. Supply with
+ 12, the pole 4 of the relay. Are the l eft
turning lights turning on? Supply with +12 V
the pole 5 of the signal relay.
Are the right turning lights turning on?
Repair the electric layout from
poles 4 and 5 of the FLASH relay.
Replace the FLASH relay.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
No
No
No
Yes
Yes
Yes
Yes No
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 40
11. Remote control signal reception 11G = activate the RF ACTIVE for 3 secondsremote control decoder receives the
Received signal indication the remote control signal
12. Remote control signal validation 11D = activate the RF ACTIVE for three sec. remote control if the signal received at
Good signal indication the decoder is good
13. Communication doors locking 14G = blocking/ unlocking ACTIVE when the switch E.C.U. decoder E.C.U. decoder receives
control fr om the
doors’ locking switch
14. Co mmunication E.C.U .decoder - 14D =activation of the doors ACTIVE doors when
doors ac tuators actuators the E.C.U. decoder
sends the command
blocking/unlocking to
the actuators of the
doors.
15. The state of the doors contact 16G = doors contact ACTIVE when the front doors are opened.
NOTE: the state
ACTIVE occurs also
if front hood or hatchback
are opened when the
vehicle is equipped
with anti intrusion system
16. Remote controls synchronisation in 17G =programming in progress ACTIVE when the process or resynchronisation TIR/ TRF remote control
resynchronisation
procedure is in pr ocess
17. RF remote controls synchronisation 17D = not performed TIR ACTIVE when the
not perfor med programming remote control
synchronisation is not
performed.
18. Not performe d key code programming 19G = unperformed key ACTIVE when the
programming key programming is
not pe rformed
19 . Validated key code programming 19D = unblocked key programmi ng ACTIVE when the
validation of the key
programming is not
performed
20 . Th e pr og ramming of the first key 18G = the memorising of the ACTIVE when the
first key programming of the
fir st key is in process
DIAGNOSTIC
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 45
Vo l u m etric protection checking.
Perform the following checking steps after locking using the RF remote control, the doors, the
engine hood and the hatchback. The operations must be performed in no more than 40 seconds
since the anti i ntrusion system has been activated with the RF remote control; if operating after
these 40 seconds, the siren will start and the turning lights will blink.
Close the door. The sound signal (buzzer)
will stop.
Th e pr oper operation of the anti intrusion system on different situations must be according to
those shown in Table 01. For detecting the causes of possible incidents of the anti intrusion system, perform the checking
steps presented in Table 02.
Lo wer the rear windows with about 10
cm. Close the doors, the engine hood
and the ha tchback.
Check out if there is any movement in
the cockpit.
Ac tivate the system pressing the button
of the RF remote control.
In troduce a hand through the window,
inside the cockpit and move it.
Th e LED indicator will blink quickly,
showing there has been a volumetric
detection and that volumetric sensors are
f unctioning correctly.
Deac tivate the system using the RF
remote contro l, then clos e al l the
vehicle windows.
Reactivate the system and then hit by
ha nd the windows surfa c e of the
vehicle. The LED indicator should
continue to normally blink and the siren
starting shall not occur.
Functional checking of the peripheral
protection.
Close the doors, the engine hood and the
hatchback.
Ac tivate the system pressing the button
of th e RF remote.
The doors will lock and the LED indicator
will blink.
Open a do or with the vehicle key.
The LED indicator will continuously be on,
a nd a sound signal (buzzer) will be heard.
Deac tivate and reactivate the sys tem
w ith the RF remote control.
Deac tivate t he system by pressing the
button of the RF remote control.
The do ors will unlock and t he LED
indicator will go off.
Rep eat a.m. operations for both front
door s, engine hood and hatchback.
FUNCTIONAL CHECKING OF THE SYSTEM
vnx.su

84
CONTROLS - SIGNALLING
84 -1
(STARTING – IGNITION SWITCH)
The anti theft mechanism is placed on the right part of the steering column and has the purpose
to starter control when electric system is connected, being provided in the same time also with a
steering locking device, with anti theft lock.
NOTE
At the anti theft mechanism there is not any more marked G position (garage) because
it does not allow the taking out of the key in this position but helps in pi n unblocking
for removing the mechanism from the steering column.
Disconnect the battery.
Dismount the steering wheel casings.
Disconnect the anti-starting bushing.
Remove the bushing off the steering column.
Disconnect the switch connection wires.
B ring the key in the interme diary position (ex G).
Dismount the attachment screw (1).
P ush the mobile pin ( 2) and pull backwards
the switch.
REMOUNTING
Mount the switch in its place.
Tighten the attachment screw(1).
Connect :
- the switch
- the battery.
Position and mount the anti-star ting bushing.
Connect the anti-starting bushing to the ve-
h icle wirin g.
Check the switch operation.
Mount the steering wheel casings. DISMOUNTING
ANTI THEFT MECHANISM
vnx.su

84
CONTROLS - SIGNALLING
84-2
CONNECTING PLUGS REPLACEMENT
The operations are to be performed after dismounting the contact switch from the vehicle.
Di smount t he a ttachment screws of the
blocking wedge guiding.
Dismount the connecting plugs.
Position and mount the connecting plugs.
Mount the blocking wedge guiding
Tighten the attachment screws of the blocking wedge guiding.
DISMOUNTING-REMOUNTING THE FIX AND MOBILEHATCHBACK CONTACT (until 01.06.2001)
FIX CONTACT
DISMOUNTING
Disconnect the battery.
Di sconnect the connections boxes from
the rear wiring. Dismount the attachment screw(2) of the
guiding body.
MOBILE CONTACT
DISMOUNTING
Dismount the contact attachment screw (1) on the hatchback.
Dismount the attachment screws of the obturator cap on the hatchback.
Disconnect the mobile contact connectors from the consumers (license plate lamps, STOP-
S3 lamp, rear window defrosting). Extract the mobile contact and its wiring.
REMOUNTING
Perform the dismounting operations in the reverse order, previously checking the contacts
base pins sliding. DISMOUNTING
REMOUNTING
Extract by detaching from clips the fix contact from the guiding body.
REMOUNTING
Perform the dismounting
operations in the reverse order. ANTI THEFT MECHANISM
vnx.su

84
CONTROLS - SIGNALLING
84-3
SI
GNALIZING AND LIGHTING CONTROL SWITCH
DISMOUNTING-REMOUNTING
The lighting control switch e quipping the SupeRNova vehicles includes also the turning-
signalizing switch .
NOTE
The lighting control switch is not to be repaired.
DISMOUNTING
Disconnect the battery.
Dismount the lower steering wheel casing.
Cut the plastic collar which is attaching the wiring on the steering column.
Disconnect the switch connector from the front wiring.
Dismount the switch attachment screw from the steering column.
Dismount the switch.
REMOUNTING
Tighten the switch attachment screws.
Connect the switch connector to the front wiring.
Position the plugs and fix with a new plastic collar.
Connect the battery.
Check the switch operation.
Mount the steering wheel lower casing.
UNDER WHEEL CONTROL MODULE
vnx.su

84
CONTROLS - SIGNALLING
84-4
DISMOUNTING-REMOUNTING OF TH E WINDSCREEN
WIPER-WASHING SWITCH
DISMOUNTING
Disconnect the battery.
Dismount the steering wheel casings.
Disconnect the switch connector.
Dismount the windscreen wiper switch attachment screws (2).
Detach the switch.
REMOUNTING
Fix the switch by tightening its attachment screws (2).
Connect the switch connector to the front wiring.
Mount the steering wheels casings.
Connect the battery.
Check the switch operation.
The SupeRNova vehicles are equipped with TAKOSAN type switches.
2
1
UNDER WHEEL CONTROL MODULE
vnx.su

84
CONTROLS - SIGNALLING
FOG LAMPS SWITCH84-5
FOG PROJECTORS SWITCH FOG LAMPS SWITCH
Pos Destination2 Fog lamp
4 High beam, low beam
5+ parking lights
6 Mass
7 Fog lamp
9 Fog lamp relay control
Pos Destination
1 + Parking lights
2 Fog lamps relay control
3 + Parking lights
4 Mass
vnx.su

84
CONTROLS - SIGNALLING
84-6
REAR WINDOW DEFROSTING SWITCH
(impulsional type)
Pos Destination
1 Relay control
3 + Parking lights
4 Mass
5 Supply + after contact
vnx.su

84
CONTROLS - SIGNALLING
84-7
HAZARD SWITCH
Pos Destination1 Supply + after contact
2 Supply + permanently
3 Left turning
4R ight turning
5+ Parking lights
6 Mass
7 Hazard indicator
8T ur ning switch
9 Supply + turning relay
vnx.su