DACIA SUPERNOVA 2004 Manual PDF

ENGINE E7J-A-2/6010
10 - 37
ENGINE AND LOWER ENGINE UNITS
TIG H TENING CO UPL E S (daNm)
Screws for fixing at front of motor-propelling frame 6.2
Screws for fixing at back of motor-propelling fram 10.2
Lower crankcase screws 1
Screws for fixing steering wheel lower axis 1.4
Screws of wheel 7.5
Screw of the ball-and-socket joint 5.5
Screw-nut of the steering ball-and-socket joint 3.5
Screw for fixing anti-swing auxiliary connecting rod (on frame) 6.2
Screw for fixing anti-swing auxiliary connecting rod (on gearbox) 10.5
D
IS M O UNT ING
The c ar i s placed on a l ifting stand with
two columns; The battery i s disconnected;
The engine is emptied of oil;
The engine-shield is taken apart ;
To take apart :
-front wheels;
-screw-nut for fixing the lower steer-
ing wheel axis on the pinion of t he steer-
ing case; -the steering ball-and-socket joints
and the arm ball-and-socket joints; -side clearance devices;
-thermic protection screen;
-catalytic convert er;
-front bumper ba r;
-anti-swing auxiliary connecting rod.
The screws for fixing the motor-propelling
s et fra me are taken a part, and the frame is
lowered; The lower c rankcase is taken apart.
R
E-MOUNT ING
The lower c rankcase is cleaned.
A ca. 3 mm-thick girdl e of RHODERSEAL
5661 is applied, as in the adjoining drawing. Do not forget to replace the two cres-
cent-sha ped fitti ngs at the e nds of the
crankcase.
Mind that the relative displacement be-
tween the lower crankcase and the cylin-
d er crankcase, along the gearbox-assem-
b ly surface, should not exceed 0.3 mm.
LOWER CRANKCASE MOUNTED ON THE CAR
LOWER CRANKCASE
vnx.su

ENGINE E7J-A-2/6010
10 - 38
ENGINE AND LOWER ENGINE UNITS
DIS M O UNT ING
The oil in the engine is emptied.
The following are taken apart: - Motor-Propelling set frame;
- lower crankcase.
The screws for fixing the oil-pump on the crankcase are taken apart;
The carrying chain is taken off the oil-pump pinion;
The cap of the oil-pump is taken apart.
The play of the pinions in the oil-pump is checked.
R
E-MOUNT ING
The dismantling operations are done in the re verse order.
Motor-oil filling-up i s done.
The pressure of the oil at 80
o is checked:
idle mode: 1 bar
4000 rot/minute 3 bar Sc
rews for fixing oil-pum p 2.5
Sc rews for fixing oil-pum p cap 1 T
IG H TENING CO UP
LES (daNm)
OIL-PUMP ON THE CAR OIL-PUMP
vnx.su

ENGINE E7J-A-2/6010
10 - 39
ENGINE AND LOWER ENGINE UNITS
TIGHTENING COUPLES (daNm)
Screws for fixing combustion-head cap1
S crew-nut for stretching distribution belt runner/pulley 5
Screws and screw-nuts M 6 for water-pump 1
Screws and screw-nuts M 8 for water-pump 2.2
Screw of the crankshaft pulley 2+68
o+/-6o
Screw of cam-shaft pin 4.5
Screws of rocker-arm ramp 2.3
S crews of flywheel 5 - 5.5
Screws of oil-pump 2.5
Screws of oil-pump cap 1
Screws of bearing caps 2.5+43
o+/-6o
Screws of combustion-head 2+97o+/-2o
Screws of the exhaust gallery 2.5
Screws of the intake gallery 2.5
Sparking plugs 2.5 - 3
Screws of the oil-crankcase 1
Screws for rocker-arm adjustment 1.5
Emptying jack 2
S crews of the connecting rod caps 4.2
Oxygen probe 4.5
TIGHTENING COUPLES
vnx.su

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
Tightening couples (daNm)
Screws of wheels7.5
Screw of the crankshaft pulley 2+68
o+/-6o
S crew-nut of stretching runner 5
Screws right-side stand 6.2
Screw-nut hydroelastic buffer 3.7
DISMONTING
The car is placed on a lifting stand.
The fore part of the engine is proppe d
on the frame using the MOT.545 device.
The following are taken apart: -front right-side wheel;
-the right-side pendular suspension;
11 - 1 -the alterna tor belt;

-the carrying belt of the compressor
(AC) ;
-the pulley of the crankshaft and its hub;
-the carryi ng pulley of the compressor;
-the distri bution crankcases.
DIS TRIBUTION BELT
vnx.su

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
The engine is set at the tuning point (see Chapter 10, pages 10-19);
The screw-nut of t he stretching runner i s loosened;
The distri bution belt is taken off.
R
E-MOUNT ING
A new distribution belt is mounted ( see Chapter 10, pages 10-33);
The tension in t he di stribution belt is checked and a djusted, by m eans of MOT.1505
device, at the value of 145-185 Hz.
The opera tions are done in the reverse order of those in the dismantling process;
The screws are tightened at the couple;
It is c ompulsory t o tighten the crankshaft pulley a t a 2 daNm couple plus a n angle of
68
o+/-6o;
The compressor pulley ( AC) is re-mounted;
The be lt of the alterna tor a nd that of the compre ssor are stretched, oberving the
values of the mounting tension:
Alternator: 263 Hz+/- 10%
Co mpressor: 222 Hz+/- 10%.
11 - 2
DISTRIBUTION BELT
vnx.su

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
SPECIAL TOOL- AND-CHECK SETS
MOT.1202-01 -”CLIC” collar-pincers
MOT.1505 -Device for measuring belt tension
MOT.484 -Device for jacket maintaining -Wrench for angular tightening
-Pincers for elastic collar
TIG H TENING CO UPL E S (daNm )
S crew-nut of stretching runner/pulley 5
Screw of crankshaft pulley 2+68
o+/-6o
Screws of pendular suspension stand 6.2
Screw-nut of hydro-elastic buffer 3.7
Wheel Screws 7.5
Co mbustion-head Screws 2+97
o+/-2o
To take apart :
-the connector of the induction coil;
-the fue l hoses (t he going- and re -
turn circ uit); -the connectors of the injectors;
-the plugs of the sparks;
-the induction coil.
11 - 3
CYLINDER HEA D FITTING
D
IS M O UNT ING
The car is placed on a two-column lift -
ing stand; The battery i s disconnected;
The cooling circuit is emptied at the
jack situated at the lower pa rt of the radia-
tor; The distribution belt is taken apart (see
Chapter Distri bution Belt);
The following are taken apart: -air-filter;
-the c onnector of the c lapper-posi-
tion potentiometer (1); -the acceleration cable;
-the connector of the atmosphe ric
pressure sensor (2);
-the co nnector of the step-by-step
engine (3); -the connector of t he air temperature
sensor (4) on the intake collector;
vnx.su

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
The hoses of the thermostat stand are
disconnected;
To take apart :
-the thermic screen;
-the exhaust collector;
-the alterna tor;
-the guide of the oil-l evel gauge;
To take apart :
-the combustion-head screws, ex-
cept the scre w corresponding to A po-
sition, which i s only loosened, then the
combustion-head is turned round the re-
maining screw; -the cylinder-head;
The ja cket -mainta ining MOT.484
device is mounted.
Check the plane of the c ylinder-head.
11 - 4
CYLINDER HEA D FITTING
vnx.su

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
RE-MOUNT ING
The plane of the fitting is cleaned and checked.
Mount the cylinder he ad with a new gasket.
The taking-apart opera tions are done in the reverse order.
The combustion-head is tightened ( see Chapter 10, pages 10-31).
The distri bution belt is mounted ( see Chapter 10, pages 10-33);
It is mounted in the reverse order of the taking-apart process;
The filling-up and the airing of the cooling circuit is done ( see Chapter “Filling-up
and draining” );
The rocker-arms are adjusted.
NOTE
At each operation requiring battery disconnection, when reconnecting, introduce
the radio code, which is written on the vehicle-buying invoice.
11 - 5
CYLINDER HEA D FITTING
vnx.su

ENGINE E7J-A-2/6012
FUEL MIXTURE
CH ARACTERISTICS
ENGINE
Car Gearbox Ty p e Index Cylinder Stroke Cylinder
bore length volume
(mm) (mm) (cm3)
SupeRNova JH3-050 E7J A-2/60 75,8 77 1390 9,5/1
Check-ups in idle mood*
Motor Emisii poluan
i
Fuel
Type Index Mode CO(%) CO2(%) HC Lambda (minimum
(rot/min) (1) ppm l octanic number)
E7 J A-2/60 750+/50 0,5 14,5 100 0,97.. .. Unleaded petrol
max min max ....1,03 (CO95)
(1) at 2500 rot /min the CO value must be max. 0.30%;
* For water t emperature over 80
oC and after stabilizing at 2500 rot/mi n for 30
seconds; then turn ba ck into idle mode and the level of fumes is measured. The water-tempera ture a nd air-t emperature sensors are type NTC (negative
temperature coefficient), and the vari ation of their re sistance as to temperature
has the following evolution:
T (0C ) 0 20 40 80 90
A ir-T sensor
11970 - 7470 4045 - 3060 1600 - 1315 - -
R (Ohm)
Engine T 8000 - 67 00 3000 - 2600 1300 - 1100 300 - 270 215 -200
sensor
R (Ohm)
12 - 1
vnx.su

ENGINE E7J-A-2/6012
FUEL MIXTURE
DENOMINATION PARTICULARITIES
Computer 90-ways connector
Injection system Multi-point sequential
Ignition PINIS R
W
Static wi th a double coil
Computer controlled ignition R
A-B1W
R
A-C0,5 W
R
B-C0,5 W
R
1-47+/-1KW
R
2-37+/-1KW
Detonation se nsor Piezoelectric type SAGEM
Tightening moment = 2 daNm
RPM SENSOR ELECTRICFIL or SIEMENS R = 200......270 W
Spark plugs EYQUEM - type RFN 58 LZ
CHAMPION - type RC 87 YCL
Fuel filter For EURO 96:
Attached under the vehicle in front of the fuel tank
Replacement on the occasion of the scheduled inspections
For EURO 00:
Into the fuel tank, attached on the fuel pump assembly.
It is no t replaced separate.
Fuel pump Immersed in the fuel tank
For EURO 96: - Flow: 1,3 l/min - Pressure: 3 bars at 12V tension
For EURO 00: - Pressure: 3,5 bars at 12V tension
Pr essure controller For EURO 96:
Pressure controller attached on the injection ramp
Controlled pressure: - 3 +/- 0,2 bars at zero depression- 2,5 +/- 0,2 bari at a depression of 500 mbars
For EURO 00:
Mounted into fuel tank on the fuel pump assembly
Controlled pressure: 3,5 bars
El ectric injectors SIEMENS
R = 14,5 +/- 1 W la 20
0C
+ 12 V supply
Step by s tep engine R
A-D = 52 +/- 5 W
R
B-C = 52 +/- 5 W
12 - 2
CH ARACTERISTICS
vnx.su