DODGE CHARGER SRT 2010 7.G Owners Manual

Cavity Car-tridge
FuseMini-
Fuse
Description
31———
32———
33———
34———
35 — 5 Amp OrangeAntenna Module –
If Equipped/Power
Mirrors
36 — 25 Amp NaturalHands-Free Phone –
If Equipped/Video
Monitor – If Equipped/
Radio
37 — 15 Amp BlueTransmissionCavity Car-
tridge
FuseMini-
Fuse
Description
38 — 10 Amp RedCargo Light/Satellite
Receiver (SDARS)
Video – If Equipped/
Vehicle Information
Module – If Equipped
39 — 10 Amp RedHeated Mirrors –
If Equipped
40 — 5 Amp OrangeAuto Inside Rearview
Mirror/Heated Seats –
If Equipped/Switch
Bank
41———
42 30 Amp Pink— Front Blower Motor
370 MAINTAINING YOUR VEHICLE

Cavity Car-tridge
FuseMini-
Fuse
Description
43 30 Amp Pink— Rear Window Defroster
44 20 Amp Blue— Amplifier –
If Equipped/Sunroof –
If Equipped
* Cavities 11, 12, and 13 contain self-resetting fuses
(circuit breakers) that are only serviceable by an autho-
rized dealer. The cluster and the driver seat switch are
fused by the 25 Amp circuit breaker in cavity 11. The
passenger seat switch is fused by the 25 Amp circuit
breaker in cavity 12. The door modules, the driver power
window switch, and the passenger power window
switch are fused by the 25 Amp circuit breaker in cavity 13. If you experience temporary or permanent loss of
these systems, see your authorized dealer for service.
VEHICLE STORAGE
If you are leaving your vehicle dormant for more than
21 days, you may want to take these steps to protect your
battery.
•Disconnect the negative cable from the battery.
•Anytime you store your vehicle, or keep it out of
service (i.e., vacation) for two weeks or more, run the
air conditioning system at idle for about five minutes
in the fresh air and high blower setting. This will
ensure adequate system lubrication to minimize the
possibility of compressor damage when the system is
started again.
7
MAINTAINING YOUR VEHICLE 371

REPLACEMENT BULBS
InteriorBulb Number
Rear Courtesy/Reading Lamps ............. W5W
Rear Compartment (Trunk) Lamp ............. 562
Overhead Console Reading Lamp ............. 578
Visor Vanity Lamps ..................... A6220
Glove Box Lamp – If Equipped ............... 194
Door Courtesy .......................... 562
Shift Indicator Lamp ................. JKLE14140
Optional Door Map Pocket/
Cupholder ....... LED (Serviced at Authorized Dealer)
NOTE: For lighted switches, see your authorized dealer
for replacement instructions.
All of the interior bulbs are glass wedge base or glass
cartridge types. Aluminum base bulbs are not approved
and should not be used for replacement. Exterior
Bulb Number
Low Beam Headlamp (Standard Halogen) ......9006
Low Beam Headlamp –
High Intensity Discharge
(HID) .......... D1S (Serviced at Authorized Dealer)
High Beam Headlamp .................... 9005
Front Park/Turn Lamp ................... 3157A
Front Fog Lamp – If Equipped ............PSX24W
Front Side Marker ........................ 194
(Serviced at Authorized Dealer)
Tail/Stop Lamp ......................... 3057
Tail/Turn Lamp ......................... 3057
Rear Side Marker ........................ 168
Backup Lamp ........................... 921
Center High-Mount Stop Lamp
(CHMSL) ....... LED (Serviced at Authorized Dealer)
License ................................ 168
372 MAINTAINING YOUR VEHICLE

BULB REPLACEMENT
Low Beam Headlamp, High Beam Headlamp,
Park/Turn Lamp, and Front Side Marker Lamp —
Models with Halogen Headlamps
1. Open the hood.
NOTE:Removal of the air cleaner filter housing may be
necessary prior to replacing bulbs in the headlamp
assembly on the driver side of the vehicle.
2.
Twist the appropriate bulb and socket assembly counter-
clockwise, and then pull it out of the headlamp assembly.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol. 3. Disconnect the bulb from the socket assembly and
install the replacement bulb.
4. Reinstall the bulb and socket assembly into the head-
lamp assembly, and then turn it clockwise.
1 — High Beam Headlamp Bulb
2 — Low Beam Headlamp Bulb
7
MAINTAINING YOUR VEHICLE 373

3 — Park/Turn Lamp Bulb4 — Side Marker Lamp Bulb
374 MAINTAINING YOUR VEHICLE

Low Beam Headlamp, High Beam Headlamp, and
Park/Turn Lamp — Models with High Intensity
Discharge Headlamps (HID)
HID Headlamps
The headlamps are a type of high voltage discharge tube.
High voltage can remain in the circuit even with the
headlamp switch off and the key removed.Because of
this, you should not attempt to service a headlamp bulb
yourself. If a headlamp bulb fails, take your vehicle to
an authorized dealer for service.
WARNING!
A transient high tension occurs at the bulb sockets of
HID headlamps when the headlight switch is turned
ON. It may cause serious electrical shock or electro-
cution if not serviced properly. See your authorized
dealer for service. NOTE:
On vehicles equipped with HID headlamps,
when the headlamps are turned on, there is a blue hue to
the lights. This diminishes and becomes more white after
approximately 10 seconds, as the system charges.
Backup Lamp, Side Marker Lamp, Tail/Turn Lamp,
and Tail/Stop Lamp
1. Open the trunk.
7
MAINTAINING YOUR VEHICLE 375

2. Remove two fasteners from the back of the taillamp
assembly.
3. Pull back the trunk liner.
4. Remove the remaining fastener from the back of the
taillamp assembly.
5. Push the electrical connector locking tab to the side.6. Disconnect the electrical connector.
7. Pull the taillamp assembly clear from the vehicle to
access the bulbs.
8. Turn the appropriate bulb and socket assembly coun-
terclockwise to remove it from the taillamp assembly.
376 MAINTAINING YOUR VEHICLE

1 — Backup Lamp Bulb2 — Side Marker Lamp Bulb
7
MAINTAINING YOUR VEHICLE 377

9. Disconnect the bulb from the socket assembly and
install the replacement bulb.
10. Reinstall the bulb and socket assembly into the
taillamp assembly, and then turn it clockwise.
3 — Tail/Turn Lamp Bulb4 — Tail/Stop Lamp Bulb
378 MAINTAINING YOUR VEHICLE

11. Reinstall the taillamp assembly, fasteners, electrical
connector, and trunk liner.
12. Close the trunk.
License Lamp
1. Remove the screws securing the lamp to the rear
fascia.
2. Remove the bulb and socket assembly.
3. Disconnect the bulb from the socket assembly and
install the replacement bulb.4. Reinstall the bulb and socket assembly.
5. Reattach the lamp to the rear fascia, and then install
the screws.
1 — License Lamp Bulb
2 — Socket
7
MAINTAINING YOUR VEHICLE 379