DODGE DURANGO 2022 Vehicle Warranty

MICHELIN®
130
INSPECT YOUR TIRES, DO NOT DRIVE ON A DAMAGED TIRE OR WHEEL
HAZARDS
Objects in the road, such as potholes, glass, metal, rocks, wood, debris and similar items,
ca

n damage a tire and should be safely avoided. Unavoidable contact with such objects
should prompt a thorough tire inspection.
Anytime you see any damage to your tires or wheels, replace with the spare at once and
i m

mediately visit any Michelin® tire retailer. For PAX® System Tires see an authorized
PAX® System tire retailer.
IMPACT DAMAGE
A tire impacted by a road hazard (curb, pothole, debris) may be damaged but not have
v i

sible signs of damage on its surface. A tire damaged by an impact may sustain a
sudden failure a day, week, or even months later. You may not recall hitting an object that
damaged or injured your tires. Air loss, unusual tire wear, localized wear or vibrations can
also be signs of internal tire damage.
If you suspect any damage to your tire or wheel from an impact with a curb, pothole or
de
bris on the road or any other road hazard, or if you feel or hear any unusual vibration,
replace with a properly inflated spare at once and immediately visit any qualified tire
technician.
INSPECTION
When inspecting your tires, including the spare, check the air pressures. If the pressure
c h

eck indicates that one of your tires has lost pressure of two pounds or more, look for
signs of penetration, valve leakage or wheel damage that may account for the air loss.
Always look for bulges, cracks, cuts, penetrations, and abnormal tire wear, particularly
o n

the edges of the tire tread, which may be caused by misalignment or underinflation.
If any such damage is found, the tire must be inspected by any Michelin® tire retailer at
once. Use of a damaged tire could result in tire destruction.
All tires will wear out faster when subjected to high speeds as well as hard cornering,
r a

pid starts, sudden stops, frequent driving on roads which are in poor condition, and off
road use. Roads with holes and rocks or other objects can damage tires and cause H
210130
V 240149
V* 240+149+
ZR** W270 168
ZR** Y300 186
ZR** 300+186+
SPEED Ratings Maximum Speed
Km/h mph

MICHELIN®
131
misalignment of your vehicle. When driving on such roads, drive carefully and slowly, and
before driving again at normal or highway speeds, examine your tires for any damage,
such as cuts, bulges, penetrations, unusual wear patterns, etc.
WEAR-BARS
Michelin® tires contain “Wear-Bars” in the grooves of the tire tread which show up when
o n

ly 2/32 of an inch (1.6 mm) of tread is remaining. At this stage, your tires must be
r e

placed. Tires worn beyond this stage are extremely dangerous.
DO NOT OVERLOAD - DRIVING ON ANY OVERLOADED TIRE IS DANGEROUS
The maximum load rating of your tires is molded on the tire sidewall. Do not exceed this
rating. Follow the loading instructions of FCA US LLC for your vehicle and this will ensure
that your tires are not overloaded. Tires which are loaded beyond their maximum
allowable loads for the particular application will build up excessive heat that may result
in sudden tire destruction.
Do not exceed the gross axle weight rating for any axle on your vehicle.
TRAILER TOWING
If you anticipate towing a trailer, you should visit any Michelin® tire retailer for advice
c o

ncerning the correct size tire and pressures. Tire size and pressures will depend upon
the type and size of trailer and hitch utilized, but in no case must the maximum cold
inflation pressure or tire load rating be exceeded. Check the tire decal and the owner’s
manual supplied by FCA US LLC for your vehicle for further recommendations on trailer
towing.
MICHELIN® PAX® System Tires/Self-Supporting Zero Pressure (ZP) Tires and Trailer
T o

wing
Operation of Pax® or ZP tires at low or zero air pressure with a trailer in tow, is dangerous
a n

d is not recommended. If the low pressure warning indicator is activated when a trailer
is in tow, stop, disconnect the trailer, and do not continue to tow the trailer until the tire
has been repaired and re-inflated to the proper air pressure. If the tire cannot be
repaired, it must be replaced with a new full size, PAX®/ZP tire, and inflated to the proper
air pressure, before the trailer can be safely towed again.
WHEEL ALIGNMENT AND BALANCING ARE IMPORTANT FOR SAFETY AND MAXIMUM
M I

LEAGE FROM YOUR TIRES.
CHECK HOW YOUR TIRES ARE WEARING AT LEAST ONCE EACH MONTH
If your tires are wearing unevenly, such as the inside shoulder of the tire wearing faster
th
an the rest of the tread, or if you detect excessive vibration, your vehicle may be out of
alignment or balance. These conditions not only shorten the life of your tires but
adversely affect the handling characteristics of your vehicle, which could be dangerous.
If you detect irregular wear or vibration, have your alignment and balance checked
immediately. Tires which have been ran underinflated will show more wear on the
shoulders than in the center of the tread.

MICHELIN®
132
TIRE MIXING
Michelin® tires are radial tires and for best performance it is recommended that the
same size and type of tire be used on all four wheel positions. Before mixing tires of
different types in any configuration on any vehicle, be sure to check the vehicle
manufacturer’s owner‘s manual for its recommendations.
It is especially important to check the vehicle manufacturer’s Owner’s Manual when
mi

xing, matching, or replacing tires on 4-wheel drive vehicles, as this may require special
precautions.
MICHELIN® DOES NOT RECOMMEND MIXING PAX® SYSTEM TIRES WITH NON-PAX®
T I

RES/SELF-SUPPORTING ZERO PRESSURE (ZP) TIRES WITH NON-ZP TIRES OTHER THAN
THE TEMPORARY USE OF THE SPARE IF THE VEHICLE IS SO EQUIPPED.
WINTER DRIVING
Tires which meet the US Tire Manufacturers Association (USMTA) definition of snow tires
are marked M/S, or M&S. On such tires, this designation is molded into the sidewall.
Tires without this notation are not recommended or Winter driving.
While All-Season tires are designed to provide reliable performance in some
Winter conditions, the use of four Winter tires is recommended for optimal
p e

rformance. Tires designate for use in severe Winter conditions are marked
on at least one sidewall with the letter “M”.
TIRE ROTATION AND REPLACEMENT
To obtain maximum tire wear, it may be necessary to rotate your tires. Refer to your
vehicle owner’s manual for instructions on tire rotation. If you do not have an owner‘s
manual for your vehicle, Michelin® recommends rotating your tires every 6,000 to
8,000 miles (10,000 to 12,000 km).
Monthly inspection for tire wear is recommended. Your tires should be rotated at the first
s i

gn of irregular wear, even if it occurs before 6,000 miles (10,000 km). This is true for
a l

l vehicles.
When rotating tires with a directional tread pattern, observe the arrows molded on the
s i

dewall which show the direction the tire should turn. Care must be taken to maintain
the proper turning direction.
Some Tire Pressure Monitoring Systems (TPMS) may not recognize that a tire has been
m o

ved to a different position on your vehicle. Make certain that your TPMS system is
reset, if necessary, so as to correctly identify the location of each tire on your vehicle.
Refer to your vehicle owner’s manual or your vehicle dealer.
Determine whether rotated tires require tire inflation adjustment as front and rear
p o

sition tire pressure may vary according to the vehicle manufacturer’s specification due
to the actual load on that wheel position. Some vehicles may have different sized tires
mounted on the front and rear axles, and these different sized tires have rotation
restrictions. Always check the vehicle owner’s manual for the proper rotation
recommendations.

MICHELIN®
133
Full-size Spare
Full-size spare tires (not temporary spares) of the same size and construction should be
u s

ed in a five tire rotation. Always check the inflation pressure of the full-size spare
immediately before incorporating it into rotation. Follow the vehicle manufacturer’s
recommended pattern for rotation, or if not available, see a qualified tire technician.
Replacement of Two Tires
It is recommended that all four tires are replaced at the same time. However, when only
t w

o tires are replaced, the new tires should be put on the rear. The new tires, with deeper
tread, may provide better grip and water evacuation in wet driving conditions.
CUSTOMIZATION OF TIRES, WHEELS, OR SUSPENSION ON SUVS AND LIGHT
TRUCKS
Due to their size, weight and higher center of gravity, vehicles such as SUVs and light
trucks do not have the same handling characteristics as automobiles. Because of these
differing characteristics, failure to operate your SUV/truck in a proper and safe manner
can increase the likelihood of vehicle rollover. Modifications to your SUV/truck tire size,
tire type, wheels or suspension can change its handling characteristics and further
increase the likelihood of vehicle rollover. Whether your SUV/truck has the original
equipment configuration for tires, wheels and suspension or whether any of these items
have been modified, always drive safely, avoid sudden, sharp turns or lane changes and
obey all traffic laws. Failure to do so may result in loss of vehicle control leading to an
accident and serious injury or death.
TIRE ALTERATIONS
Do not make or allow to be made any alterations on your tires. Alterations may prevent
proper performance, leading to tire damage which can result in an accident. Tires which
become unserviceable due to alterations such as truing, whitewall inlays, addition of
balancing or sealant liquids, or the use of tire dressing containing petroleum distillates
are excluded from warranty coverage.
REPAIRS WHEREVER POSSIBLE, SEE YOUR MICHELIN® TIRE RETAILER AT ONCE
If any MICHELIN® tire sustains a puncture, have the tire demounted and thoroughly
inspected by any MICHELIN® tire retailer for possible damage that may have occurred.
A tread area puncture in any MICHELIN® passenger or light truck tire can be repaired
provided that the puncture hole is not more than 1/4 inch in diameter, not more than
o n

e radial cable per casing ply is damaged, and the tire has not been damaged further
by the puncturing object or by running underinflated. Tire punctures consistent with
these guidelines can be repaired by following the US Tire Manufacturers Association
(USTMA) recommended repair procedures.
TIRE REPAIRS
Repairs of all tires must be of the combined plug and inside patch type. Your MICHELIN®
PAX® System tires must be removed from the wheel for inspection prior to repair. Plug
only repairs are improper. A tire should be removed from the rim and inspected prior to

MICHELIN®
134
repair. Any tire repair done without removing the tire from the rim is improper. An
improperly repaired tire will cause further damage to the tire by either leaking air or
allowing air, moisture and contaminants to enter the structure of the tire. An improperly
repaired tire can fail suddenly at a later date.
Never repair a tire with less than 2/32nds of an inch tread remaining. At this tread depth,
th

e tire is worn out and must be replaced.
STORAGE
Tires contain waxes and emollients to protect their outer surfaces from ozone and
weather checking. As the tire rolls and flexes, the waxes and emollients continually
migrate to the surface, replenishing this protection throughout the normal use of the tire.
Consequently, when tires sit outdoors, unused for long periods of time (a month or more)
their surfaces become dry and more susceptible to ozone and weather checking and the
casing becomes susceptible to flat spotting. For this reason, tires should always be
stored in a cool, dry, clean, indoor environment. If storage is for one month or more,
eliminate the weight from the tires by raising the vehicle or by removing the tires from
the vehicle. Failure to store tires in accordance with these instructions could result in
damage to your tires or premature aging of the tires and sudden tire failure.
When tires are stored, be sure they are placed away from sources of heat and ozone such
a s

hot pipes and electric generators. Be sure that surfaces on which tires are stored are
clean and free from grease, gasoline or other substances which could deteriorate the
rubber. Tires exposed to these materials during storage or driving could be subject to
sudden failure.
FOLLOW THESE MOUNTING RECOMMENDATIONS
Tire changing can be dangerous and must be done by professionally trained persons
using proper tools and procedures as specified by the Rubber Manufacturers
Association (RMA). PAX® System tires must be mounted and dismounted only by
specially trained, authorized PAX® System retailers, utilizing PAX® System authorized
equipment.
Your tires should be mounted on wheels of correct size and type and which are in good,
cle
an condition. Wheels that are bent, chipped, rusted (steel wheels) or corroded (alloy
wheels) may cause tire damage. The inside of the tire must be free from foreign material.
Have your retailer check the wheels before mounting new tires. Mismatched tires and
rims can explode during mounting. Also, mismatched tires and rims can result in
dangerous tire failure on the road. If a tire is mounted by error on the wrong-sized rim, do
not remount it on the proper rim, scrap it. It may have been damaged internally (which is
not externally visible) by having been dangerously stretched and could fail on the
highway.
Old valves may leak. When new tubeless tires are mounted, have new valves of the
c o

rrect type installed. Tubeless tires must only be mounted on wheels designed for
tubeless tires i.e., wheels which have safety humps or ledges. As with any other tire air
valve, the PAX® System valve stem-pressure sensor combination must be in good

MICHELIN®
135
condition to assure its performance. Always utilize valve caps capable of containing the
tire’s air pressure, should the valve core leak. The valve cap is the primary seal against
air loss.
It is recommended that you have your tires and wheels balanced. Tires and wheels which
a r

e not balanced may cause steering difficulties, a bumpy ride, and irregular tire wear.
SPECIAL MOUNTING INSTRUCTIONS FOR PAX® SYSTEM TIRES
PAX® System wheels are different from all other wheels. Never attempt to mount a
non-PAX® System tire on a PAX® System wheel, or a PAX® System tire on a non-PAX®
System wheel. Attempting to do so could cause serious injury or death. All PAX® System
components (tire, wheel, support ring, pressure sensor and gel) must be utilized. Never
utilize a PAX® System tire and wheel without every other properly functioning component
part, correctly installed by an Authorized PAX® System retailer. The PAX® System must
be used on all wheel positions.
After a low or zero pressure driving event, the PAX® System tire and wheel may be hot to
th

e touch. Always allow a PAX® System tire to cool before attempting to handle it. Failure
to do so could result in injury.
SPECIAL MOUNTING INSTRUCTIONS FOR SELF-SUPPORTING ZERO PRESSURE™ (ZP)
T I

RES
ZP tires can be more difficult to mount than conventional tires. They should be mounted
a n

d demounted only by a properly trained tire professional. ZP tires can generate a
tremendous amount of heat when run at low or zero pressure. ALWAYS ALLOW A ZP TIRE
TO COOL BEFORE ATTEMPTING TO HANDLE IT. FAILURE TO DO SO COULD RESULT IN
INJURY.
MICHELIN® ZP tires are tubeless tires designed to operate in emergency conditions at
lo
w or zero air pressure.
MICHELIN® SELF SUPPORTING Zero Pressure™ (ZP) TIRES AND SPECIAL SYMMETRIC
H U

MP-MODIFIED (SH-M) WHEELS
Some MICHELIN® ZP tires can only perform with zero pressure capability when mounted
o n

special SH-M wheels. These tires bear the SH-M designation immediately following
the ZP designation on the sidewall of the tire. DO NOT MOUNT ZP TIRES WITH THE SH-M
DESIGNATION ON STANDARD WHEELS. IN SUCH APPLICATIONS, THE TIRES MAY
BECOME UNSERVICEABLE AT LOW OR ZERO PRESSURE, CAUSING SERIOUS PERSONAL
INJURY OR DEATH.
SPECIAL MOUNTING INSTRUCTIONS FOR MICHELIN® TRX™ TIRES
The MICHELIN® TRX™ tire is a tubeless tire that must only be mounted on special wheels
( T

R or JM type) with millimetric seat diameter. If TRX tires are mounted on standard
wheels, they will not retain air due to an air escape feature designed into the bead area
of these tires.
Do not try to override this feature by mounting TRX tires with tubes. The MICHELIN®
T R

X™ tire must be used on all wheel positions.

MICHELIN®
136
TEMPORARY TYPE SPARE TIRES
When using any temporary type spare tire, be sure to follow the vehicle manufacturer’s
in

structions.
READING THE DOT
DOT XXXX XXXX XXX (prior to August 2000)
DOT XXXX XXXX XXX (1990-1999)
DOT XXXX XXXX XXXX (after July 2000)
THE DOT
The “DOT” symbol certifies tire manufacturer’s compliance with US Department of
Transportation tire safety standards. Next to the symbol is the tire identification or “serial
number”. The first two characters identify the plant where the tire was manufactured.
The next two characters reflect the tire size. The following one to four digits may be used
at the tire manufacturer’s option as a descriptive code. The last three characters are
numbers identifying the week and year of manufacture. (Example: “O25” means second
week of the year of decade, eg.: 1995, 1985, etc.) For the 1990-1999 decade
MICHELIN® brand tires are marked with a triangle pointing to the last three numeric
characters. Tires produced after July 2000 have an additional digit to identify a given
decade. For example, 2800 means the tire was produced during the 28th week of 2000;
0 2

01 during the 2nd week of 2001. If the last digits of your DOT number contains three
numeric characters and is not marked with a triangle, consult a qualified tire technician
to determine the year of manufacture.
SERVICE LIFE FOR PASSENGER CAR AND LIGHT TRUCK TIRES INCLUDING SPARE
TIRES
The following recommendation applies to passenger car and light truck tires. Tires are
composed of various types of material and rubber compounds, having performance
properties essential to the proper functioning of the tire itself. These component
properties evolve over time. For each tire, this evolution depends upon many factors
such as weather, storage conditions, and conditions of use (load, speed, inflation
pressure, maintenance etc.) to which the tire is subjected throughout its life. This
service-related evolution varies widely so that accurately predicting the serviceable life
of any specific tire in advance is not possible.
That is why, in addition to regular inspections and inflation pressure maintenance by
c o

nsumers, it is recommended to have passenger car and light truck tires, including
spare tires, inspected regularly by a qualified tire specialist, such as a tire dealer, who
will assess the tire’s suitability for continued service. Tires which have been in use for five
years or more should continue to be inspected by a specialist at least annually.
Consumers are strongly encouraged to be aware not only of their tires’ visual condition
and inflation pressure but also of any change in dynamic performance such as increased
air loss, noise or vibration, which could be an indication that the tires need to be removed
from service to prevent tire failure. It is impossible to predict when tires should be

MICHELIN®
137
replaced based on their calendar age alone. However the older a tire the greater the
chance that it will need to be replaced due to the service-related evolution or other
conditions found upon inspection or detected during use.
While most tires will need replacement before they achieve 10 years, it is recommended
t h

at any tires in service 10 years or more from the date of manufacture, including spare
tires, be replaced with new tires as a simple precaution even if such tires appear
serviceable and even if they have not reached the legal wear limit. For tires that were on
an original equipment vehicle (i.e., acquired by the consumer on a new vehicle), follow
the vehicle manufacturer’s tire replacement recommendations, when specified (but not
to exceed 10 years).
The date when a tire was manufactured is located on the sidewall of each tire.
C o

nsumers should locate the Department of Transportation (DOT) code on the tire which
begins with DOT and ends with the week and year of manufacture. For example, a DOT
code ending with “2204” indicates a tire made in the 22nd week (May) of 2004.
REMEMBER TO AVOID DAMAGE TO YOUR TIRES AND POSSIBLE ACCIDENT
• CHECK TIRE PRESSURE AT LEAST ONCE EACH MONTH WHEN TIRES ARE COLD AND BEFORE LONG TRIPS.
• D O NOT UNDERINFLATE/OVERINFLATE.
•
DO NOT OVERLOAD.
•
DRIVE AT MODERATE SPEEDS, OBSERVE LEGAL LIMITS.
•
AVOID DRIVING OVER POTHOLES, OBSTACLES, CURBS OR EDGES OF PAVEMENT.
•
AVOID EXCESSIVE WHEEL SPINNING.
•
IF YOU SEE ANY DAMAGE TO A TIRE, REPLACE WITH THE SPARE AND VISIT ANY
M
ICHELIN® TIRE RETAILER AT ONCE.
• I F YOU HAVE ANY QUESTIONS CONTACT YOUR MICHELIN® TIRE RETAILER.
F
AILURE TO OBSERVE ANY OF THE RECOMMENDED PRECAUTIONS CONTAINED IN THIS
O W

NER’S MANUAL CAN LEAD TO ERRATIC VEHICLE BEHAVIOR AND/OR TIRE DAMAGE,
POSSIBLY RESULTING IN AN ACCIDENT.
If you see any damage to your tires or wheels, contact your local participating Michelin®
t i

re retailer listed in the Yellow Pages, or visit our web site listed below for dealer
locations. If further assistance is required, contact:
IN USA 1-800-847-3435 or write:
Michelin® North America, Inc.
Attention: Consumer Care Department Post Office Box 19001
Greenville, SC 29602-9001
or visit: www.michelinman.com .

MICHELIN®
138
IN CANADA 1-888-871-4444 or write:
Michelin® North America (Canada) Inc.3020 Jacques-Bureau Avenue Laval, QuebecH7P 6G2
or visit: www.michelin.ca .

MICHELIN®
139