DODGE RAM 1500 GAS 2007 3.G Owners Manual

Page 501 of 568

NOTE:For easier removal, pull the headlight assembly
straight forward, applying the greatest amount of force to
the outer edge of the headlight assembly.
5. Unlock and pull connector straight from the base of
the headlight halogen bulb.
6. Twist connector on the side marker/turn signal/park
light bulb
14turn and remove connector and bulb from
housing.
Headlight Removal
Bulb Removal
MAINTAINING YOUR VEHICLE 501
7

Page 502 of 568

7. Remove housing from vehicle with headlight halogen
bulb in housing.
8. Twist the headlight halogen bulb
14turn and remove
headlight bulb from the housing.
9. Replace headlight or side marker/turn signal/park
light bulb. Do not touch the headlight halogen bulb.
10. Reverse procedure for installation of bulbs and hous-
ing.
Fog Lights
1. Reach under the vehicle, unlock and twist connector
counterclockwise14turn and remove connector and bulb
from housing.
502 MAINTAINING YOUR VEHICLE

Page 503 of 568

2. Pull bulb straight from the connector.
3. Reverse procedure for installation of bulbs and hous-
ing.Tail, Stop, Turn and Backup Lights
1. Remove the two (2) screws that pass through the bed
sheetmetal.
Removing the Two (2) Screws
MAINTAINING YOUR VEHICLE 503
7

Page 504 of 568

2. Pull the housing straight out from the body, with a
quick motion, to separate the housing from the body. If
not pulled straight, locators may be damaged.3. Rotate the bulb socket counterclockwise to remove
from the housing.
Pulling Housing From Body
Rotating Bulb Socket From Housing
504 MAINTAINING YOUR VEHICLE

Page 505 of 568

4. Pull bulb straight out of socket. 5. Reverse Procedure to install bulb and housing. Place
the two raised blocks passed the body.
Pulling Bulb From Socket
Sliding Raised Blocks Past Body
MAINTAINING YOUR VEHICLE 505
7

Page 506 of 568

Center High-Mounted Stoplight (CHMSL) With
Cargo Light
1. Remove the two (2) screws holding the housing/lens
to the body as shown.2. Separate the connector holding the housing and wir-
ing harness to the body.
3. Turn desired bulb socket
14turn and remove socket
and bulb from housing.
506 MAINTAINING YOUR VEHICLE

Page 507 of 568

4. Pull desired bulb straight from the socket.
•Outside Bulbs: Cargo Lamps
•Inside Bulb: Center High Mount Stop Lamp
5. Reverse procedure for installation of bulbs and hous-
ing.
Cab Top Clearance Lights — If Equipped
1. Remove the two screws from the top of the light.
MAINTAINING YOUR VEHICLE 507
7

Page 508 of 568

2. Rotate the socket14turn and pull it from the light
assembly.3. Pull the bulb straight from it’s socket and replace.
508 MAINTAINING YOUR VEHICLE

Page 509 of 568

Tailgate ID Lights (Dual Rear Wheels) — If
Equipped
1. Remove the two screws and housing and access the
bulb sockets from the rear.
MAINTAINING YOUR VEHICLE 509
7

Page 510 of 568

2. Turn socket14turn counterclockwise to access the
bulb.
3. Pull bulb straight out from socket.
4. Reverse procedure for installation of bulbs and hous-
ing.Rear Light Bar ID Marker (Dual Rear Wheel) – If
Equipped
1. Loosen the two screws and the housing to gain access
to the bulb sockets.
2. Turn the socket 1/4 turn counterclockwise to access
the bulb.
510 MAINTAINING YOUR VEHICLE

Page:   < prev 1-10 ... 461-470 471-480 481-490 491-500 501-510 511-520 521-530 531-540 541-550 ... 570 next >