check engine DODGE SPRINTER 2004 1.G User Guide

STARTING AND OPERATING 155
5
Electronic Brake Force Distribution (EBD)The electronic brake force distribution (EBD) prevents
the rear wheels from being overbraked when there is
little load on the rear axle or if there is not much friction
between the tires and road (e.g., if the road is wet).
A cceleration Skid Control Indicator Lamp (A SR)
and Brake A ssist System (BA S) if equippedWhen the key is in position 2 in the ignition lock, the
indicator lampk will light up in the instrument
cluster as a function check. It goes out when the engine
is running.
WARNING!
If the brake indicator lamp ;(-) does not
go out or lights up again while driving, the brake
fluid level may not necessarily have dropped be-
low the minimum filling capacity but a malfunc-
tion may have occurred in the EBD. In this case
continue driving, but with even greater care.
The wheels of the rear axle could lock if the
vehicle is braked hard. This could lead to a
skidding of the vehicle. Have the malfunction
traced and repaired without delay by an
authorized Sprinter Dealer.
Adapt your speed and driving style to the
prevailing road, traffic and weather conditions.
Driving too fast increases the risk of an accident.
Freightliner-all.book Pag e 155 Monday, December 1, 2003 2:54 PM

STARTING AND OPERATING 161
5
For the indicator lamp k refer to
"Indicator Lamp
Acceleration Skid Control (ASR) and Brake Assist
System (BAS)
".
Indicator Lamp Electronic Stability Program (ESP)
(Cargo/passenger vans type 2500 C/HC/SHC only)When the key is in position 2 in the ignition lock, the
ESP indicator lamp will light up in the instrument
cluster as a function check. It goes out when the engine
is running.
If the indicator lamp remains on or lights up when
the engine is running, the electronic stability program
(ESP) is malfunctioning and switched off
automatically. The engine’s power output may be then
reduced.
WARNING!
The Brake Assist system (BAS) cannot prevent the
natural laws of physics from acting on the vehicle,
nor can it increase braking efficiency beyond that
afforded by the condition of the vehicle brakes
and tires or the traction afforded.
The BAS cannot prevent accidents, including
those resulting from excessive speed in turns,
following another vehicle too closely, or
hydroplaning. Only a safe, attentive, and skillful
driver can prevent accidents.
The capabilities of an BAS equipped vehicle must
never be exploited in a reckless or dangerous
manner which could jeopardize the user’s safety
or the safety of others
.
Adapt your speed and driving style to the
prevailing road, traffic and weather conditions.
Driving too fast increases the risk of an accident.
Freightliner-all.book Pag e 161 Monday, December 1, 2003 2:54 PM

STARTING AND OPERATING 163
5
STEERINGWhen the engine is not running, there is no power
assistance for the steering. Greater force will be
required to steer the vehicle.WHEELS AND TIRESCheck tires regularly for even tread wear, tread depth
(note legal requirements) and signs of external
damage.
Only use wheels and tires of the same size, make and
pattern.
Do not install tires that are not approved for the size
and type of wheel installed or the vehicle itself. Only
use those wheel sizes which were delivered to you by
your authorized Sprinter Dealer.
Use only wheels and tires which have been tested and
approved by the vehicle manufacturer.
Break in new tires at moderate speeds for a distance of
about 65 miles (about 100 km).
WARNING!
ESP cannot prevent the natural laws of physics
from acting on the vehicle, nor can it increase the
traction afforded.
The ESP cannot prevent accidents, including
those resulting from excessive speed in turns,
following another vehicle too closely, or
hydroplaning. Only a safe, attentive, and skillful
driver can prevent accidents.
The capabilities of an ESP equipped vehicle must
never be exploited in a reckless or dangerous
manner which could jeopardize the user’s safety
or the safety of others.If the vehicle is to be towed away with the front
wheels clear of the ground, or if the brakes are to be
tested on a brake dynamometer, do not put the key
in position 2 in the ignition lock because the ESP
would engage the brakes to stabilize the vehicle.If the ESP function is used for a prolonged period
of time, the rear axle brakes may fail due to
overheating.
Freightliner-all.book Pag e 163 Monday, December 1, 2003 2:54 PM

170 STARTING AND OPERATINGSNOW CHA INSInstall snow chains on rear wheels only. Install snow
chains on exterior wheel in vehicles with double tires.
Comply with the manufacturer’s installation
instructions.
NOTE: Vehicles with snow chains installed are only to
be driven on a snow-covered surface. The snow chains
must be removed on road surfaces free of snow.FUELSUse only commercially available vehicular diesel fuels
No. 2 or No. 1 (ASTM D 975 No. 2-D or No. 1-D).
If diesel fuels are used with a sulphur content
exceeding 0.05 % by weight, engine oil change
intervals must be shortened. Please contact your
Sprinter Dealer to obtain the necessary information.
Marine diesel fuel, heating oil or the like must not be
used.
Refueling from drums or canisters may lead to the fuel
becoming contaminated. This in turn can cause faults
in the fuel system. Always filter the fuel before adding
it to the vehicle’s tank.
Fuel Filter with Water SeparatorCheck the water separator when the fuel indicator
lamp does not go out or comes on while the engine
is running. For more information on the indicator
lamp .
The interval for changing the fuel filter is reduced to
10,000 miles (about 15,000 km).
Freightliner-all.book Pag e 170 Monday, December 1, 2003 2:54 PM

198 WHAT TO DO IN EMERGENCIES
Tightening torque for 9,990 lbs (4,530 kgs)
(vehicle type 3500 C/HC/SHC):
Steel wheel – 138 lbf.ft ±14 lbf.ft (190 N.m ±20 N.m)
 Remove jack and stow it in the vehicle tool kit.
 Check the tire pressure.
 Re-tighten the wheel bolts to the specified torque
with a torque wrench after a distance of 30 miles
(about 50 km).
JUMP STA RTINGIf the battery is dead, the engine can be started with
jumper cables from another vehicle’s battery.
WARNING!
After changing a wheel, you must, for safety reasons,
 have the specified tightening torque checked. The
wheels could otherwise work loose.
 check the tire pressure and correct it if necessary.
 retighten the wheel bolts and wheel nuts to the
specified tightening torque once the vehicle has
been driven for 30 miles (50 km).
 have a reversed direction of tire rotation corrected
as soon as possible at a qualified specialist
workshop. The vehicle handling characteristics
could otherwise be affected.
WARNING!
A battery will also produce hydrogen gas, which
is flammable and very explosive. Avoid open
flames and the formation of sparks in the vicinity
of the batteries. Refrain from smoking or cell
phone use. Avoid improper connection of jumper
cables.
Observe safety precautions when handling
batteries.
Exercise care near moving engine components and
electrical cables.
Failure to follow these directions will cause
damage to the electronic components and can lead
to a battery explosion and severe injury or death.
Freightliner-all.book Pag e 198 Monday, December 1, 2003 2:54 PM

MAINTAINING YOUR VEHICLE
7
CONTENTS
Engine Compartment . . . . . . . . . . . . . . . . . . . . . . . 205

Sprinter Original Parts . . . . . . . . . . . . . . . . . . . . . . 207

Service Products . . . . . . . . . . . . . . . . . . . . . . . . . . . 207Disposal of Service Products . . . . . . . . . . . . . . 208

Emission Related Component Warranty
Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208

Regular Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208Windshield Washer System Fluid Reservoir . 209Air Filter Restriction Indicator (Optional) . . . 209Engine Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209Engine Oil Level . . . . . . . . . . . . . . . . . . . . . . . . 210Ribbed V-Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . 211Hydraulic Brake System, Clutch Mechanism
Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212Engine Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Checking Coolant Level . . . . . . . . . . . . . . . . . . 213

Winter Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 215

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216Disconnecting the Battery . . . . . . . . . . . . . . . . . 216Reconnecting the Battery . . . . . . . . . . . . . . . . . . 217Charging the Battery . . . . . . . . . . . . . . . . . . . . . 217

Replacing Wiper Blades . . . . . . . . . . . . . . . . . . . . . 218Appearance Car and Corrosion Protection . . 219Power Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . 220Automatic Car Wash . . . . . . . . . . . . . . . . . . . . . 221Tar Stains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221Paintwork, Painted Body Components . . . . . . 221Engine Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 221Vehicle Washing . . . . . . . . . . . . . . . . . . . . . . . . . 222Ornamental Moldings . . . . . . . . . . . . . . . . . . . . 222Headlamps, Taillamps, Turn Signal Lenses . . 222Window Cleaning . . . . . . . . . . . . . . . . . . . . . . . 223
Freightliner-all.book Pag e 203 Monday, December 1, 2003 2:54 PM

208 MAINTAINING YOUR VEHICLEDisposal of Service ProductsDispose of service products and of parts which come
into contact with them (e.g. filters) in an
environmentally responsible manner. Comply with
applicable bars and regulations.EMISSION RELA TED COMPONENT WA RRA NTY
STATEMENTThe Manufacturer warrants to the original and each
subsequent owner of a MERCEDES-BENZ heavy-duty
on highway diesel engine that:
(1) the engine was designed, built and equipped so as
to conform at the time of sale with the applicable
regulations adopted by the Federal Environmental
Protection Agency
(2) the emission control system of such engine is free
from defects in materials and workmanship which
would cause it not to conform with those regulations
for a period of use of five years or 100 000 miles or
3 000 hours of engine operation, whichever occurs
first.
REGULA R CHECKSThe following checks should be performed at regular
intervals (for example once a week or each time the
vehicle is refueled):
 Windshield cleaner system – fluid reservoir.
 Air strainer, in vehicles with an air strainer element
maintenance indicator (optional equipment).
 Engine oil level.
 Checking ribbed V-belt.
 Hydraulic brake system, clutch mechanism fluid
level.
 Coolant level.
 Tire and spare wheel condition and pressures of the
same. For more information, refer to "Wheels and
Tires".
 Vehicle lighting.
Freightliner-all.book Pag e 208 Monday, December 1, 2003 2:54 PM

210 MAINTAINING YOUR VEHICLEEngine Oil Level 1. Oil dipstick
2. Oil filler neckCheck the engine oil level at regular intervals with the
vehicle standing on a level surface.
 Check engine oil level about 5 minutes after
stopping the engine, which should have reached its
regular operating temperature. The normal
operating temperature should have been reached
and maintained for some time.
 Wipe the dipstick clean with a lint-free cloth before
checking.
The engine oil level must be between the
lower (MIN) and upper (MAX) marks on
the dipstick.
Add engine oil only up to the MAX mark.
Excess oil must be drained or siphoned off.
 For approved engine oils, contact your Sprinter
Dealer.Freightliner-all.book Pag e 210 Monday, December 1, 2003 2:54 PM

MAINTAININ G YOUR VEHICLE 211
7
Ribbed V-BeltThe ribbed V-belt drives the accessories, such as
generator, coolant pump and hydraulic steering pump.
The ribbed V-belt is automatically kept tensioned.
Check the state of the ribbed V-belt regularly, such as
at every engine oil level check.
The belt must not be damaged, worn, oiled or glazed.
There must be no cracks in the belt running surface.
Replace damaged belts.
Hydraulic Brake System, Clutch Mechanism Fluid
Level1. Brake fluid reservoir
Brake fluid level must be between the MIN and MAX
marks in the reservoir (1).
If the brake fluid is below the MIN mark, there may be
a fault in the hydraulic system. Have the system
checked as soon as possible by an authorized Sprinter
Dealer.
Freightliner-all.book Pag e 211 Monday, December 1, 2003 2:54 PM

MAINTAININ G YOUR VEHICLE 213
7
Have the coolant renewed at least every five years or
after 100,000 miles.
When the coolant is renewed, the new coolant should
contain 50% antifreeze/corrosion inhibitor by volume.
This corresponds to antifreeze protection down to -
37 °C/-35°F.
Do not exceed a proportion of about 55 % by volume
(antifreeze protection down to about -45 °C/-49 °F) as
the heat dissipation properties then deteriorate.
In the event of coolant loss, do not add water only, but
sufficient antifreeze/corrosion inhibitor to maintain
the correct concentration.
The water in the coolant must satisfy certain
requirements. These are often met by tap supply
drinking water.
The water must be specially prepared if the water
quality does not come up to the required standards.
Have the corrosion inhibitor/antifreeze concentration
in the coolant checked at the outset of winter,
respectively once a year in countries with high
prevailing temperatures.A regular check is included in the maintenance service.
Checking Coolant LevelCoolant reservoir (1)
The cooling system is pressurized. Only check the
coolant level with the vehicle parking on a level surface
and with the engine switched off.
– Wait until the coolant temperature has dropped
below 194 °F (+90 °C).
Freightliner-all.book Pag e 213 Monday, December 1, 2003 2:54 PM