oil change DODGE SPRINTER 2004 1.G Owners Manual

164 STARTING AND OPERATING
WARNING!
Fitting other wheel sizes to the vehicle will change
the vehicle’s handling characteristics and may
lead to an accident resulting in severe personal in-
juries, death and property damage.
Do not use retreaded/ remolded tires. This process
does not always permit previous damage to the
detected. Therefore vehicle safety cannot be
guaranteed if retreaded/remolded tires are fitted
.
WARNING!
A wheel could work loose. To avoid the risk of serious or
fatal injuries or vehicle damage, please bear the follow-
ing points in mind: Always replace wheel bolts that are damaged or
rusted.
 Never apply oil or grease to wheel bolts. If a wheel hub thread is damaged, you must not drive the
vehicle. Consult a qualified specialist workshop. Be sure to use correct mounting bolts. Check
tightness of wheel bolts or nuts regularly and
retighten with a torque wrench, if necessary.
Tighten wheel bolts or nuts in a cross-pattern
sequence.Mounting bolts and tightening torque, see Chapter 12,
‘‘Installing a Wheel’’. After changing a wheel, the wheel bolts or nuts
must be tightened once the vehicle has been
driven for about 30 miles (50 km).If new or repainted wheels are fitted, the wheel bolts or
nuts must be retightened again after about 600 to 3,000
miles (about 1,000 to 5,000 km).
Freightliner-all.book Pag e 164 Monday, December 1, 2003 2:54 PM

170 STARTING AND OPERATINGSNOW CHA INSInstall snow chains on rear wheels only. Install snow
chains on exterior wheel in vehicles with double tires.
Comply with the manufacturer’s installation
instructions.
NOTE: Vehicles with snow chains installed are only to
be driven on a snow-covered surface. The snow chains
must be removed on road surfaces free of snow.FUELSUse only commercially available vehicular diesel fuels
No. 2 or No. 1 (ASTM D 975 No. 2-D or No. 1-D).
If diesel fuels are used with a sulphur content
exceeding 0.05 % by weight, engine oil change
intervals must be shortened. Please contact your
Sprinter Dealer to obtain the necessary information.
Marine diesel fuel, heating oil or the like must not be
used.
Refueling from drums or canisters may lead to the fuel
becoming contaminated. This in turn can cause faults
in the fuel system. Always filter the fuel before adding
it to the vehicle’s tank.
Fuel Filter with Water SeparatorCheck the water separator when the fuel indicator
lamp does not go out or comes on while the engine
is running. For more information on the indicator
lamp .
The interval for changing the fuel filter is reduced to
10,000 miles (about 15,000 km).
Freightliner-all.book Pag e 170 Monday, December 1, 2003 2:54 PM

188 WHAT TO DO IN EMERGENCIES
Procedure:
1. Park the vehicle on a firm, level, non-slippery
surface.
2. Switch on the hazard warning flasher switch, apply
the parking brake, and place the transmission
selector in "P".
WARNING!
The jack is designed exclusively for jacking up the
vehicle at the jack take-up brackets built into ei-
ther side of the vehicle. To help avoid personal in-
jury, use the jack only to lift the vehicle during a
wheel change. Never get beneath the vehicle
while it is supported by the jack only.
Keep hands and feet away from the area under the
lifted vehicle. Always firmly set parking brake
and block wheels before raising vehicle with jack.
Do not disengage parking brake while the vehicle
is raised.
Always use the jack on a level surface.
Do not change wheels on either steep uphill or
downhill grades. Be sure that the jack arm end is
fully seated in the jack take-up bracket. The
vehicle may begin to move and fall from the jack
which could cause serious or fatal personal injury
and property damage.
Always lower the vehicle onto sufficient capacity
jack stands before working under the vehicle.
Precautions when changing a wheel:
For the torque, refer to "Installing a wheel";
Do not damage, grease or oil wheel bolts or their
threads.
Do not jack the vehicle up more than 1.2 in (30
mm) between the tire and the surface. Otherwise,
the vehicle may tip over and may cause serious
injury or death to you or others.
Precautions when changing a wheel:
For the torque, refer to "Installing a wheel";
Do not damage, grease or oil wheel bolts or their
threads.
Freightliner-all.book Pag e 188 Monday, December 1, 2003 2:54 PM

196 WHAT TO DO IN EMERGENCIESINSTALLING A WHEELWheel bolts for pressed steel wheels (1)
Wheel bolts for light-alloy wheels (Optional) (2)NOTE: The optional light alloy wheels are supplied
with 5 short wheel lug bolts enclosed for the steel spare
wheel in the vehicle tool kit.
 Before fitting the spare wheel, clean rust and dirt off
the contact surfaces of the wheel and the wheel hub,
and from the wheel bolts.
 Note the specified wheel and tire size, tire load
capacity and speed code.
 Do not change the tire’s direction of rotation.
 Do not damage, grease or oil wheel bolts or their
threads.
WARNING!
Different wheel bolts are required for pressed
steel and light-alloy wheels.
Incorrect wheel lug bolts for the wheels could
work loose, thereby causing you to lose control of
the vehicle. This could cause an accident resulting
in severe personal injuries and and property
damage.
Freightliner-all.book Pag e 196 Monday, December 1, 2003 2:54 PM

MAINTAININ G YOUR VEHICLE 215
7
(1.5 cm) above the base area which is visible
through the filler opening.
 Replace and tighten the radiator cap.
If a large quantity of coolant has been lost, or if smaller
amounts are lost at regular intervals, have the engine
cooling system examined by an authorized Sprinter
Dealer.
For coolant composition and water quality, contact
your Sprinter Dealer.
WINTER OPERATIONHave your vehicle winterized by an authorized
Sprinter Dealer before the onset of winter.
 Have the engine oil changed, if the engine oil filled
is not approved for winter use.
 Coolant: antifreeze/anti-corrosion concentration in
the coolant checked.
 Windshield washer system: add winter concentrate
to the washer fluid.
 Battery: the battery will lose capacity as
temperatures drop. Only a well-charged battery will
ensure reliable engine starting even at low outside
temperatures.
 Tires: fit M+S radial tires, taking note of the
maximum permissible speed of the tires fitted.
Freightliner-all.book Pag e 215 Monday, December 1, 2003 2:54 PM

MA INTENA NCE SCHEDULES
CONTENTS
8M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248

Maintenance - Without ASSYST Maintenance
Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249Maintenance Intervals . . . . . . . . . . . . . . . . . . . . 249

Maintenance - With ASSYST Maintenance
Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250

Regular Check-Ups. . . . . . . . . . . . . . . . . . . . . . . . . 250

Special Maintenance Requirements . . . . . . . . . . . 251Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Dust Filter for Heating/Ventilation
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251

Engine Oil Change and Filter Replacement . . . . 251Once a Year . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251

Scope of Work for Maintenance service . . . . . . . 252Oil Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252Additional Maintenance Work . . . . . . . . . . . . . 254Additional Maintenance Work
After ... Years . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
Freightliner-all.book Pag e 247 Monday, December 1, 2003 2:54 PM

MAINTENANCE SCHEDULES 251
8M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
SPECIAL MAINTENANCE REQUIREMENTSIf bodies built by manufacturers other than
DaimlerChrysler Corporation are fitted to the vehicle, the
maintenance requirements and lubrication intervals
specified by the body manufacturer must be adhered to,
in addition to all standard maintenance requirements.Brake FluidOnly use brake fluids approved by the manufacturer
(DOT 4 plus). Information about brake fluids is
available from your Sprinter Dealer.CoolantHave the corrosion inhibitor/antifreeze concentration
in the coolant checked before the onset of winter (once
a year in countries with high prevailing temperatures).
Have the coolant renewed every five years or 100,000
miles.Dust Filter for Heating/Ventilation ReplacementThe dust filter and the tailgate interior filter are
renewed during routine maintenance service.
However, if operating conditions are dusty, these
filters should be renewed more frequently.
ENGINE OIL CHA NGE A ND FILTER
REPLACEMENTIn a minimum, change the engine oil and oil filter once
a year - even if the vehicle mileage per year is extremly
low. For standard oil service schedules, please see the
chapter oil service and maintenance service.Once a YearSelect the viscosity of the engine oil (SAE classes)
according to the outside air temperature.
Only use engine oil approved by DaimlerChrysler
Corporation if following the ASSYST system
guidelines.
Information is available from your Sprinter Dealer.
If the fuel used has a sulphur content exceeding 0.05 %
by weight, the service intervals should be split in half.
If the sulphur content of the fuel used is between 0.3%
and 0.8% by weight, the service intervals should be
split in half (i.e. every 5,000 miles instead of every
10,000 miles).
Freightliner-all.book Pag e 251 Monday, December 1, 2003 2:54 PM

252 MAINTENANCE SCHEDULES
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S8
SCOPE OF WORK FOR MA INTENA NCE SERVICE
Oil ServiceOil change
Engine:
Oil change and filter replacement
Check fluid levels of the following system, refill as
necessary.
If fluid is lost, trace and eliminate cause – as a separate
order.
Power-assisted steering
Lubrication work:
Trailer tow hitch (original equipment)
Maintenance
ASSYST maintenance computer resetFunction check
Signalling system,
warning and indicator lamps
Headlamps, exterior lighting
Windscreen wipers,
windscreen washer system
Check for leaks and damage.
Check for abrasion points and ensure that
lines are correctly routed!
All assemblies:
Engine, transmission, transfer case, front axle, rear
axle, steering, power steering pump
All lines and hoses, sensor cables
Rubber boots on front axle drive shafts,
rubber boots on front axle suspension ball joints, shock
absorbersFreightliner-all.book Pag e 252 Monday, December 1, 2003 2:54 PM

254 MAINTENANCE SCHEDULES
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S8
A dditional Maintenance WorkAutomatic transmission once only at 80,000 miles/
128000km
Oil and filter change
During every second maintenance service
Air cleaner without maintenance indicator:
Air cleaner filter element renewal
Check poly-V-belt for wear and signs of damage
During every sixth maintenance service
Rear axle
A dditional Maintenance Work A fter ... YearsEvery 3 years
Air cleaner filter element renewal
(note installation date
)
Every 5 years or 100,000 miles
Coolant renewal
Note coolant composition
Freightliner-all.book Pag e 254 Monday, December 1, 2003 2:54 PM

268 INDEXLock, Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Locking, Central. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55MMaintenance Computer . . . . . . . . . . . . . . . . . . . . . . . 103
Maintenance Intervals. . . . . . . . . . . . . . . . . . . . . . . . . 249
Maintenance Schedules
Additional Maintenance Work
After ... Years . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Dust Filter for Heating/Ventilation
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Engine Oil Change and Filter Replacement . . . . 251
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Oil Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Once a Year . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Regular Check-Ups. . . . . . . . . . . . . . . . . . . . . . . . . 250
Scope of Work for Maintenance service . . . . . . . 252
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
With ASSYST Maintenance Computer . . . . . . . . 250Without ASSYST Maintenance Computer . . . . . 249
Maximum Engine Speed. . . . . . . . . . . . . . . . . . . . . . . 136
Mechanical Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Mechanical Sun Roof Operation . . . . . . . . . . . . . . . . . 75
Mirror Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Mirrors
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Mopar® Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
Multi-Function Indicator . . . . . . . . . . . . . . . . . . . . . . . 87
Multifunction Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . 66
OOccupant Restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Opening/Closing doors . . . . . . . . . . . . . . . . . . . . . . . . 23
Operation, Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Ornamental Moldings . . . . . . . . . . . . . . . . . . . . . . . . . 222
Outlet, Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Outside Temperature Display . . . . . . . . . . . . . . . . . . . 91
Freightliner-all.book Pag e 268 Monday, December 1, 2003 2:54 PM