steering DODGE SPRINTER 2006 1.G User Guide

96 UNDERSTANDING YOUR INSTRUMENT PANEL
Multi-Function Indicator
WARNING!
Never operate buttons (1, 2, 3 and 4) in the multi-
function indicator while driving.
To operate these buttons the driver must reach
through the steering wheel, which could
significantly impede its movement.
Your attention will also be diverted from the road
and traffic conditions.
This could cause you to lose control of the vehicle
and could lead to an accident and result in severe
personal injuries or death.
For this reason, make sure that the traffic
conditions are safe before pressing the buttons, so
that nobody may be endangered.
When possible, reach around the steering wheel
to operate the multi-function indicator buttons.
Do not rest your head or chest on the steering
wheel or dashboard when operating the buttons.

UNDERSTANDING YOUR INSTRUMENT PANEL 123
4
Heated Rear Window (Optional)
The switch for the heated rear
window is located on the right-hand
side next to the steering column.
It can be used only when the engine
is running.
To switch it on:
 Press upward; the indicator lamp in the switch will
light up.
To switch off:
 Press upward one more time.
NOTE: The heated rear window will automatically
switch off after about 15 minutes or when the engine is
turned off.Windshield Heater (Optional)
The switch for the windshield heater
is located on the center section of the
dashboard.
It can be used only when the engine
is running.
To switch it on:
 Press upward; the indicator lamp in the switch will
light up.
To switch off:
 Press upward one more time.
NOTE: The windshield heater will automatically
switch off after about 5 minutes or when the engine is
turned off.

UNDERSTANDING YOUR INSTRUMENT PANEL 139
4
NOTE: Only on vehicles with automatic heater
control/regulated air conditioner:
Before switching on the heater or entering the switch-
on time, the temperature control (1) must be set to
maximum heater output (as illustrated).
Set the air distribution control (3) as required between
Y and Z.
AUXILIARY HEAT EXCHANGER IN LOAD
COMPARTMENT, ONLY WITH AUXILIARY HEATER
(OPTIONAL)
The auxiliary heat exchanger switch
is located on the right next to the
steering column.To switch on at blower speed 1:
Press the upper section, the left-hand indicator lamp in
the switch lights up.
To switch on at blower speed 2:
Press the lower section, the right-hand indicator lamp
in the switch lights up.
To switch off :
Press the switch to the middle position.
Operation is only possible when the key is turned to
position 2 in the ignition lock.
NOTE: The auxiliary heat exchanger in the load
compartment should be switched off at coolant
temperatures below 176 °F (+80 °C) to quickly de-fog
and de-ice the windshield and front side windows.

142 STARTING AND OPERATING
…Deactivating the Acceleration Skid
Control (ASR) . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
…Brake Assist System (BAS)
(vehicle type 2500 only) . . . . . . . . . . . . . . . . . . . 172
…Indicator Lamp Electronic Stability Program
(ESP®) (vehicle type 2500 only) . . . . . . . . . . . . 173
…Electronic Stability Program (ESP®)
(vehicle type 2500 only) . . . . . . . . . . . . . . . . . . . 174
Q Auxiliary Drive (Optional) . . . . . . . . . . . . . . . . . . 175
Q Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Q Wheels and Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 176
…Radial-Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . 179
…Important Guidelines . . . . . . . . . . . . . . . . . . . . 179…Tire Care and Maintenance . . . . . . . . . . . . . . . . 180
…Tire Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 180
…Life of Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181…Tread Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
…Storing Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
…Cleaning Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 182…Direction of Rotation . . . . . . . . . . . . . . . . . . . . . 182
…Vehicles type 2500 C/HC/SHC . . . . . . . . . . . . 185
…Vehicles type 3500 C/HC/SHC . . . . . . . . . . . . 185
…Tire Grip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185…Hydroplaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
…Recommended Tire Inflation Pressure . . . . . . 186
…Important Notes on Tire Inflation Pressure . . 187
…Checking Tire Inflation Pressure . . . . . . . . . . . 188
…Potential Problems associated with
Underinflated and Overinflated Tires . . . . . . . 190
…Tire Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
…Tire Size Designation, Load and
Speed Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
…Tire Sizes for Sprinter Vehicles . . . . . . . . . . . . . 193
…Design Standard . . . . . . . . . . . . . . . . . . . . . . . . . 193…Tire Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
…Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
…Tire Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193…Rim Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
…Tire Load Rating . . . . . . . . . . . . . . . . . . . . . . . . . 193
…Tire Speed Rating . . . . . . . . . . . . . . . . . . . . . . . . 195…DOT, Tire Identification Number (TIN) . . . . . 196
…DOT (Department Of Transportation) . . . . . . 197
…Manufacturer’s Identification Mark . . . . . . . . 197…Tire Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
…Tire Type Code . . . . . . . . . . . . . . . . . . . . . . . . . . 197
…Date of Manufacture . . . . . . . . . . . . . . . . . . . . . 197…Maximum Tire Load . . . . . . . . . . . . . . . . . . . . . 198
…Maximum Tire Inflation Pressure . . . . . . . . . . 199
…Tire Ply Material . . . . . . . . . . . . . . . . . . . . . . . . . 200
…Tire and Loading Terminology . . . . . . . . . . . . 200…Rotating Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
…Alignment and Balance . . . . . . . . . . . . . . . . . . . 206

144 STARTING AND OPERATING
POWER ASSISTANCE STARTING THE ENGINE
Battery charge warning lamp (1)
Engine oil level indicator lamp (2)
WARNING!
When the engine is not running, there is no power
assistance for the brake and steering system. In
this case, it is important to keep in mind that a
considerably higher degree of effort is necessary
to brake and steer the vehicle.

158 STARTING AND OPERATING
Protect sharp edges with padding.
 Check the tire pressures after loading the vehicle.
For passenger vans:
 Do not stack loads higher than the upper edge of the
backrests.
 Always place the load against the backrests of the
seat benches.
 Whenever possible, transport loads behind seats
that are not occupied.
 Distribute the load in such a way that the
permissible axle loads are not exceeded when the
vehicle is equipped with the maximum number of
seats. Loading the luggage compartment up to the
maximum payload would cause the permissible
rear axle load to be exceeded.BRAKES
Service Brake
WARNING!
When the engine is not running, the brake and
steering systems are without power assistance.
Under these circumstances, a much greater effort
is necessary to stop or steer the vehicle.
After driving in heavy rain for some time without
applying the brakes or through water deep
enough to wet brake components, the first
braking action may be somewhat reduced and
increased pedal pressure may be necessary. Be
sure to maintain a safe distance from vehicles in
front.
Resting your foot on the brake pedal will cause
excessive and premature wear of the brake pads.
It can also result in the brakes overheating,
thereby significantly reducing their effectiveness.
It may not be possible to stop the vehicle in
sufficient time to avoid an accident.

STARTING AND OPERATING 165
5
as the voltage reaches this level again – the ABS is then
reactivated.
If ABS malfunctions, the other driving safety systems
are deactivated. The handling and braking
characteristics of your vehicle change. The other
braking and driving systems still function normally.
I
Anti-Lock Brake System (ABS)
ABS prevents the wheels from locking at any speed
above about 5 mph (8 km/h), regardless of road
surface conditions. The vehicle remains steerable even
if the brakes are applied fully.
A light vibrating of the steering wheel and pulsating of
the brake pedal indicate that the ABS is working.
On slippery road surfaces, the ABS will respond even
with light brake pedal pressure because of the
increased likelihood of locking wheels. The pulsating
brake pedal can be an indication of hazardous road
conditions and works as a reminder to take extra care
while driving.
WARNING!
If the ABS indicator lamp- does not go out or
lights up again while driving, the ABS is malfunc-
tioning. If ABS malfunctions, the other driving
safety systems are deactivated. The vehicle’s brak-
ing characteristics may be affected. There is an in-
creased risk that your vehicle could skid in the
event of sharp braking. Have the malfunction
traced and repaired without delay by an autho-
rized Sprinter Dealer.
Adapt your speed and driving style to the
prevailing road, traffic and weather conditions.
Driving too fast increases the risk of an accident.

166 STARTING AND OPERATING
WARNING!
Do not reduce the force applied to the brake pedal if
it is necessary to brake the vehicle further. This will
negate the main benefit of ABS – the ability to brake
without affecting the steerability of the vehicle.
In the event of an emergency stop, fully depress
the brake pedal. Do not pump the brake pedal,
rather use firm, steady brake pedal pressure.
Pumping the pedal defeats the purpose of ABS
and significantly reduces braking effectiveness.
WARNING!
Anti-lock brake system (ABS) cannot prevent the
natural laws of physics from acting on the vehicle,
nor can it increase braking or steering efficiency
beyond that afforded by the condition of the vehi-
cle brakes and tires or the traction afforded.
The ABS cannot prevent accidents, including
those resulting from excessive speed in turns,
following another vehicle too closely, or
hydroplaning. Only a safe, attentive, and skillful
driver can prevent accidents.
The capabilities of an ABS equipped vehicle must
never be exploited in a reckless or dangerous
manner which could jeopardize the user’s safety
or the safety of others.
Adapt your speed and driving style to the
prevailing road, traffic and weather conditions.
Driving too fast increases the risk of an accident.

176 STARTING AND OPERATING
STEERING
When the engine is not running, there is no power
assistance for the steering. Greater force will be
required to steer the vehicle.
WHEELS AND TIRES
The tires on a new vehicle provide a balance of many
characteristics. They should be inspected regularly for
wear and correct cold tire inflation pressure. The
vehicle manufacturer strongly recommends to use tires
equivalent to the originals in size, quality and
performance when replacement is needed. Refer to the
Tire and Loading Information placard on the driver’s
door B-pillar for the size designation of your tire.
The service description and load identification will be
found on the original equipment tire. Failure to use
equivalent replacement tires may adversely affect the
safety, handling, and ride of your Sprinter vehicle.Contact an authorized Sprinter Dealer or an
authorized tire dealer with any questions you may
have on tire specifications or capability.
CAUTION!
Power take off must not exceed 10 kW. Exceeding
the power take off may cause damage to the
auxiliary drive and/or ribbed V-belt.
WARNING!
Only use tires which have been tested and ap-
proved for your Sprinter vehicle by the vehicle
manufacturer. Tires approved by the vehicle man-
ufacturer are developed to provide best possible
performance in conjunction with the driving safe-
ty systems on your Sprinter vehicle such as ABS or
ESP
®.
Using tires other than those approved by the
vehicle manufacturer may result in damage that is
not covered by Warranty.

STARTING AND OPERATING 177
5
For more information on tire size designation, load and
speed rating, refer to "Tire Labeling". See an authorized
Sprinter Dealer for information on tested and
recommended rims and tires for summer and winter
operation. They can also offer advice concerning tire
service and purchase.
WARNING!
Using tires other than those approved by the vehi-
cle manufacturer can have detrimental effects,
such as
 poor handling characteristics
 increased noise
 increased fuel consumption
Moreover, tires and rims not approved by the
vehicle manufacturer may, under load, exhibit
dimensional variations and different tire
deformation characteristics that could cause them
to come into contact with the vehicle body or axle
parts. Damage to the tires or the vehicle may be
the result.
WARNING!
Do not use a tire, wheel size or rating other than
that specified for your Sprinter vehicle. Some
combinations of unapproved tires and wheels
may change suspension dimensions and perfor-
mance characteristics, resulting in changes to
steering, handling, and braking of your Sprinter
vehicle. This can cause unpredictable handling
and stress to steering and suspension compo-
nents. You could lose control and have an accident
resulting in serious injury or death. Use only the
tire and wheel sizes with load ratings approved
for your Sprinter vehicle, refer to "Tire and Load-
ing Information". Never use a tire with a smaller
load index or speed index or capacity, other than
what was originally equipped on your Sprinter
vehicle. Using a tire with a smaller load index
could result in tire overloading and failure. You
could lose control and have an accident.
Failure to equip the vehicle with tires having
adequate speed capability can result in sudden
tire failure and loss of vehicle control.