air filter DODGE TRUCK 1993 Service Repair Manual

0 - 2
LUBRICATION
AND
MAINTENANCE

• Commercial service
When a vehicle is continuously subjected to severe
driving conditions, lubricate:
• Body components
• All the driveline coupling joints
• Steering linkage More often than normal driving conditions

DUSTY
AREAS
With this type of severe driving condition, special
care should be given to the:
• Engine air cleaner filter
• PCV filter
• Crankcase ventilation system
• Brake booster control valve air filter. Verify that the filters and the associated compo­
nents are clean. Also verify that they are functioning
effectively. This will minimize the amount of abra­ sive particles that enter the engine.

OFF-ROAD
(4WD)
OPERATION
After off-road (4WD) operation, inspect the under­
side of the vehicle. Inspect the:
• Tires
• Body structure
• Steering components
• Suspension components • Exhaust system
• Threaded fasteners

HARSH
SURFACE ENVIRONMENTS
After extended operation in harsh environments,
the brake drums, brake linings, and rear wheel bear­ ings should be inspected and cleaned. This will pre­
vent wear and erratic brake action.

ROUTINE MAINTENANCE
The following routine maintenance is recommended
on a monthly basis: TIRES—Inspect the tires for unusual wear/damage.
Determine if the inflation pressure is adequate for
the vehicle load. BATTERY—Inspect and clean the terminals.
Tighten the terminals if necessary. FLUIDS—Determine if the component fluid levels
are acceptable. Add fluid, if necessary. LIGHTS/ELECTRICAL—Test all the electrical sys­
tems in the vehicle for proper operation. It is also recommended that the engine oil and the
washer fluid level be determined at each fuel fill-up.

VEHICLE
NOISE CONTROL
Vehicles with a GVWR of 4 535 kg (10,000 lbs), or
more, are required to comply with Federal Exterior Noise Regulations (Fig. 2).
VEHICLE
NOISE
EMISSION
CONTROL INFORMATION

DATE
OF
VEHICLE
MANUFACTURE

THIS
VEHICLE CONFORMS
TO
U.S. EPA REGULATIONS FOR NOISE EMISSION

APPLICABLE
TO
MEDIUM
AND HEAVY
DUTY
TRUCKS. THE
FOLLOWING
ACTS OR THE CAUSING THEREOF BY ANY PERSON ARE PROHIBITED BY THE NOISE CONTROL ACT
OF 1972. (A) THE
REMOVAL
OR

RENDERING
INOPERATIVE, OTHER
THAN
FOR
PURPOSES
OF
MAINTENANCE,
REPAIR.
OR REPLACEMENT, OF ANY NOISE CONTROL DEVICE OR ELEMENT OF
DESIGN
(LISTED
IN
THE
OWNERS
MANUAL)
INCORPORATED
INTO
THIS
VEHICLE
IN COMPLIANCE
WITH
THE NOISE CONTROL
ACT:
(B) THE
USE
OF
THIS
VEHICLE
AFTER SUCH DEVICE
OR
ELEMENT
OF
DESIGN HAS BEEN REMOVED
OR
RENDERED
INOPERATIVE.

PU626D

Fig.
2 Vehicle
Noise
Emission
Control Information
Label

UNAUTHORIZED
DEFEAT
OF
NOISE
CONTROL COMPONENTS
Federal law prohibits removal, altering or other­
wise defeating any noise control component. This in­
cludes before or after the vehicle is in use. Federal
law also prohibits the use of a vehicle after a noise
control component is defeated.

REQUIRED MAINTENANCE/SERVICE
FOR
NOISE
CONTROL

The following maintenance is required after each
6-month or 9 600 km (6,000 miles) interval. This will
ensure that the vehicle noise control components are
operating properly.

EXHAUST SYSTEM
Inspect exhaust system for exhaust leaks and dam­
aged components. The exhaust hangers, clamps and
U-bolts should be attached and in good condition.
Burned or ruptured mufflers, damaged exhaust pipes should be replaced. Refer to Group 11—Exhaust Sys­
tem/Intake Manifold for service information.

AIR
FILTER
HOUSING/CANISTER
Inspect the air filter assembly for proper fit. Verify
the cover is securely attached to the housing/canis­
ter. Inspect all the air filter housing hoses for con­ nections. The gasket between the air filter housing and throttle body must be in good condition. The air
filter element should be clean and serviced according
to the maintenance schedule.

FUEL
REQUIREMENTS
GASOLINE
ENGINES
All engines require the use of unleaded gasoline to
reduce the effects of lead to the environment. Also unleaded fuel is necessary to prevent damage to the
catalytic converter/02 sensor. The fuel must have a
minimum octane rating of 87 based on the (R + M)/2
calculation method.

GASOLINE ENGINE MAINTENANCE SCHEDULE

LIGHT
DUTY
CYCLE

SCHEDULED
MAINTENANCE
FOR
EMISSIONS
CONTROL
-
PROPER
VEHICLE
PERFORMANCE

Inspection and service is also necessary any
rime
a
malfunction
is observed or suspected.

X
= Scheduled maintenance for all vehicles.

O
= Scheduled maintenance for all vehicles, Recommended for proper
vehicle
performance.
Where both
time
and mileage Miles (Thousand) are
shown,
follow the
interval

which
occurs
first. Kilometers (Thousand) 7'A
15
22'A
30
37'A
45
52'A

60
67'A
75
82'A

90 97'/2 105 112'A
120
Where both
time
and mileage Miles (Thousand)
are
shown,
follow the
interval

which
occurs
first. Kilometers (Thousand) 12 24
36 48
60 72 84 96 108 120
132 144 156 168 180 192

Coolant
Condition,
Coolant
Hoses/Clomps
X X X X X X

O O O O O
O O O
o
O

Exhaust
System—Check
X
X X X X

X
O O O

o
O
O O
o o o

Oil—Change
(6 months)
X X X X X X

O O O

o o

O O
o o
o
Oil Filter—Change (2nd Oil Change)
X
X X
o o
O
o
o

Spark
Plug—Replace
X

0
o o

Air
Filter—Replace
X

o

O
o

Coolant—Flush/Replace
(36 months) &
24
months/48 000 km
(30,000
miles)
thereafter
O

X
X

PCV
Valve—Replace if
Necessary
O'
O' O'

Battery—Replace
O

This maintenance is recommended by Chrysler Corporation to the owner, but is not
required
to
maintain
the
warranty.

0 - 6
LUBRICATION
AND
MAINTENANCE
GASOLINE ENGINE MAINTENANCE SCHEDULE

HEAVY
DUTY
CYCLE

Inspection and service is also necessary anytime
a
malfunction is observed or suspected.
When both
time
and mileage
are
Miles (Thousand)

shewn,
follow
the
interval

which occurs first. Kilometers (Thousand) 6
12 18 24
30 36 42 48 54
60 66 72

78
82V2
84 90
96
102 108
When both
time
and mileage
are
Miles (Thousand)

shewn,
follow
the
interval

which occurs first. Kilometers (Thousand) 9.6 19 29
38 48 58 67 77
85 96 106 116
125 132
135
145
154 164
174

Coolant
Condition, Coolant
Hoses/Clamps
X
X X X
X X X X
X X X X
X X X
X X X

Exhaust
System
—
Check
X X X X X X X X X X X
X X X X X
X X

Oil
—
Change
(6
Months)
X X X X X X X
X X

X
X
X

X X X

X X
X

Oil
Filter
—
Change (2nd
Oil
Change)
X X X X
X X
X X
X

Drive Belt Tension
—
Inspect
&
Adjust
X' X
X1

X X' X

Drive Belts (V-Type)
—
Replace
X

Air
Filter/Air
Pump
Air
Filter
—
Replace
X X X
X

Crankcase
Inlet
Air
Filter
(6 &
8
Cyl.
Eng.
Only)
—
Clean
X X
X X

Spark
Plug
—
Replace
X X X

Fuel
Filter
—
Replace as necessary

Coolant
—
Flush/Replace
(36
months)
& 24
months/48
000 km

(30,000
miles)
thereafter
X
EGR
Valve
&
Tube
—
Replace X2

EGR
Tube
—
Clean Passengers
X2
PCV
Valve
—
Replace X2

Vacuum
Emission
Components
—
Replace
X

Ignition Timing
—
Adjust
to
Specs,
as necessary X
Ignition Cables, Distributor Cap
&
Rotor
—
Replace
X

Manifold Heat Control Valve
—
Lubricate
X

Battery
—
Replace X

Oxygen
Sensor
—
Replace
X2

1 For California vehicles, this maintenance is recommended
by
Chrysler Motors
to the
owner but, is not
required
to
maintain the
warranty
on the
air
pump drive
belt.

2 Requires
Emission
Maintenance Reminder Light.
If
so equipped, these parts
are to be
replaced
at the
indicated mileage,
or
when the
emissions
maintenance reminded light remains on continuously
with
the key in the
"on" position, whichever occurs first.
J9100-20

DIESEL
ENGINE
MAINTENANCE
SCHEDULE
HEAVY
DUTY
CYCLE
Inspection
and
service
is
also
necessary
any
time
a
malfunction
is
observed
or
suspected.

Iff both
time
and distance Miles (Thousand)
are listed, use the
interval

that
ends
first. Kilometers (Thousand) 6
12
18 24
30 36 42

4S
54
60 66
72 78
84 90 96
102 108
Iff both
time
and distance Miles (Thousand)
are listed, use the
interval

that
ends
first. Kilometers (Thousand) 9,6 19
29
38 48 58 67

77

85 96 106
116 125 135 145 154
164 174

Coolant
Condition, Coolant
Hoses/Clamps
(12 months)

Coolant
Flush/Replace (36 months) & 24 months/
48 000 km
(30,000
miles)
thereafter
O

Oil—Change
(6 months)
X X X
X X X
X X X X X
X X X X X X
X

Oil Filter—Replace (Every Oil Change)
X X X
X X X
X X
X X X
X
X X X X
X X

Drive Belts—Replace
As
Necessary
X X
X X X X

Air Filter—Replace
X X
X X

Air Filter—Clean (California Only) e

®

• •
Air
Filter
Canister—Clean
o o o
o

Fuel Filter—Service When Necessary

Injection
Pump
Timing & Engine Idle Speed—

Check
& Adjust
©

• 9 • • •
Underhood Rubber/Plastic Components—Inspect/Replace • • • • •

X
— All vehicles
O
— All
vehicles
except
California.
Recommended
for
California.
•
— California only.
Recommended
for all vehicles.

0 - 14
LUBRICATION
AND
MAINTENANCE

•
ENGINE
MAINTENANCE

INDEX

page
Air
Injection
Systems/Air Pump
. 17

Air-Conditioner
Compressor
21
Battery
19

Cooling System
15

Crankcase
Ventilation
System
17
Diesel Engine
Air Filter
Canister
17

Drive Belts
20
Engine
Air
Cleaner
Filter
Element
16

Engine Break-In
14

Engine
Oil 14

Engine
Oil
Change
and Filter
Replacement
15

Exhaust Gas
Recirculation
(EGR) System
...... 19
page
Exhaust
Manifold
Heat
Control
Valve
. 17
Exhaust System
, 21

Fuel System
18

Hoses
and
Fittings
16
Ignition
Cables,
Distributor
Cap and
Rotor
...... 19

Ignition
Timing
. 19

Oxygen
(02)
Sensor
19
Rubber/Plastic Components
20

Spark Plugs
. 19

Throttle
Control
Linkage
18

Vacuum Operated, Emission
Control
Components
19

ENGINE BREAK-IN
After first starting a new engine, allow it to idle
for 15 seconds before shifting into a drive gear. Also:
• Drive the vehicle at varying speeds less than 88
km/h (55 mph) for the first 480 km (300 miles).
• Avoid fast acceleration and sudden stops.
• Do not drive at full-throttle for extended periods of
time
• Do not drive at constant speeds
• Do not idle the engine excessively A special break-in engine oil is not required. The
original engine oil installed is a high quality lubri­
cant. New engines tend to consume more fuel and oil un­
til after the break-in period has ended.

ENGINE
OIL SPECIFICATIONS

API SERWICE
GRADE
Use an engine oil that conforms to API Service
Grade S5 SG/CD or SG/CE. MOPAR®provides engine
oils that conform to all of these service grades.

SULFATED ASH—DIESEL ENGINES
Oils that contain an excessive amount of sulfated
ash can cause deposits to develop on Diesel engine
valves. These deposits can result in valve wear.

SAE
WISC0SITY
An SAE viscosity grade is used to specify the vis­
cosity of engine oil. SAE 30 specifies a single viscos­
ity engine oil.
Engine oils also have multiple viscosities. 10W-30

<
5W-30

1
1 1

F
-20 0 10 20 32 60 80 100

C
-29 -18 -12 -7 0 16 27 38
ANTICIPATED
TEMPERATURE RANGE BEFORE
NEXT
OIL
CHANGE
J9000-39

Fig.
1 Temperature/Engine Oil Viscosity—Gasoline
Engines

-12°C
-18°C 10°F
0°F- 15W-40

-23°c(^-10eF

I
10W-30
WITH
WITHOUT
BLOCK HEATER
BLOCK
SYNTHETIC
OIL

HEATER
10W-30 5W-30

J9100-29

Fig.
2 Temperature/Engine Oil Viscosity—Diesel
Engines

ENERGY
G0NSERWING
OIL
An Energy Conserving type oil is recommended for
gasoline engines. They are designated as either EN­
ERGY CONSERVING or ENERGY CONSERVING

II.
OIL
LEVEL
INDICATOR (DIPSTICK)

GASOLINE ENGINES
The engine oil indicator is located at the right
front of the engine.

0-18
LUBRICATION
AND
MAINTENANCE

•
COOLANT FREEZE PROTECTION

Cooling systems contain a 50/50 mixture of anti­
freeze (ethylene glycol) and distilled water. This is
the recommended coolant mixture.
It is recommended that the degree of coolant pro­
tection be tested every 12 months. If the coolant is
contaminated or rusty, the cooling system should be
drained, flushed. Refill with a 50/50 mixture of fresh
coolant. Refer to Group 7—Cooling Systems for addi­
tional information.

SYSTEM
INSPECTION

WARNING:
IF THE
ENGINE
HAS
BEEN RECENTLY
OPERATED,
DO NOT
REMOVE
THE
RADIATOR

CAP.
THIS WILL AVOID
YOU
BEING SCALDED

WITH
HOT, PRESSURIZED COOLANT.

(1) Test the radiator cap for proper sealing and op­
eration. Use caution when removing the radiator cap
to avoid contact with hot coolant. Place a heavy rag
or towel over the cap and turn to the first stop. Do
not press down. Pause to allow the pressure to re­
lease through the overflow tube. Then press down
and turn counterclockwise to remove the cap.
(2) Inspect the coolant overflow tubing and the
connections at the coolant reserve tank and at the
radiator.
(3) Inspect the entire cooling system for leaks. A
black-light detector can be used as an aid in detect­ ing the source of coolant leaks.
(4) Inspect the radiator and air conditioner con­
denser fins for debris, etc. (5) If necessary, refer to Group 7—Cooling Systems
for additional information and service procedures.

RADIATOR CAP
The radiator cap must be completely tightened to
provide proper pressure. Inspect and test radiator cap
when cooling system service is performed.

MAIN,
FLUSH
AND
FILL

WARNING: ANTI-FREEZE (ETHYLENE GLYCOL)
IS
POISONOUS.
KEEP
OUT OF THE
REACH
OF
CHIL­

DREN.

Drain, flush, and fill the cooling system at the in­
terval specified in maintenance schedule. For proper service instructions see Group 7, Cooling System.

HOSES AND
FITTINGS
It is recommended that rubber hoses be periodi­
cally inspected. Inspect all hose fittings for looseness and corrosion.
ENGINE
AIR
CLEANER
FILTER
ELEMENT

MAINTENANCE
SCHEDULE
With normal driving conditions, the engine air
cleaner filter element should be replaced:
• Light-Duty Cycle-after each 48 000 km (30,000
miles) interval has elapsed
• Heavy-Duty Cycle-after
each
38 000 km (24,000
miles) interval has elapsed
When the vehicle is operated in dusty areas, the
filter element should be replaced more often.
For Diesel engines, the air filter canister should be
cleaned at the same time the filter is replaced.

SERVICE/REPLACEMENT
(1) Remove the air cleaner cover.
(2) Remove the air cleaner filter (Fig. 4).

CAUTION:
Do not tap the filter or immerse the filter medium in liquid to remove trapped debris.
(3) Clean filter by blowing the trapped debris from
the filter with compressed air (Fig. 5). Direct the air in the opposite direction of normal intake air flow.
Keep the air nozzle at least two inches away from
the filter.
(4) If the filter has become partially saturated with

oil,
replace the filter. Inspect the crankcase ventilat­
ing system for proper operation.
(5) Wash the air cleaner cover and body with
cleaning solvent. Wipe it dry.
(6) Install the air cleaner filter element. Attach
the cover to the body (Fig. 4).
Fig,
4
Engine
Air Oeaner—
Typical

•

Fig.
5
Cleaning
Filter
Element—Typical

DIESEL
ENGINE
AIR
FILTER CANISTER MAINTENANCE SCHEDULE

The Diesel engine air filter should be cleaned after
each interval specified in the Diesel engine mainte­
nance schedule.
When the vehicle is operated in dusty areas, the
canister should be cleaned more frequently.

EXHAUST
MANIFOLD HEAT CONTROL VALVE
MAINTENANCE SCHEDULE
The exhaust manifold heat valve should be ser­
viced after the interval specified in the maintenance schedule has elapsed.
SERVICE The exhaust manifold heat valve is located at the
left manifold (Fig. 6). Test the valve for non-re­ stricted movement.
Fig.
6 Manifold Heat Control
Valve
LUBRICATION
AND
MAINTENANCE
0 - 17

Fig.
7 Positive
Crankcase
Ventilation

System—Typical

SYSTEM OPERATION
Each PCV system is comprised of an air inlet filter,
a flow-control (PCV) valve, and the associated hoses.
The air inlet filter is located at the cylinder head cover (Fig. 7).
WARNING:
USE
EXTREME CAUTION WHEN
THE

ENGINE
IS
OPERATING.
DO NOT PUT
YOUR
HANDS NEAR
THE
DRIVE BELT(S), PULLEYS
OR

FAN BLADE.
DO NOT
STAND
IN A
DIRECT LINE

WITH
THE FAN
BLADE.

(1) With the engine idling, accelerate momen­
tarily. The valve shaft counterweight should move CLOCKWISE.
(2) If no movement is observed, either the shaft is
binding or the thermostat spring is weak or broken. (3) If the thermostat spring is weak or broken, re­
place the spring.
(4) Verify the manifold is COOL. Apply
MOPAR®Rust Penetrant (or an equivalent product)
to each end of the valve shaft at the bearings (Fig.
6).

(5) Allow the solvent to penetrate for a few min­

utes.
Then, rotate the valve shaft back and forth un­
til it turns without restriction.

AIR INJECTION SYSTEMS/AIR PUMP
Air injection system/air pump valves and switches
should be periodically tested for proper operation. In­
spect the check valve tubing for corrosion. Replace it
if excessive corrosion exists.

CRANKCASE
VENTILATION
SYSTEM
All gasoline engines are equipped with a positive
crankcase ventilation (PCV) system. The PCV sys­
tem prevents emission of residual engine oil vapor
from the crankcase (Fig. 7).

0-18
LUBRICATION
AND
MAINTENANCE

• MAINTENANCE SCHEDULE
A crankcase ventilation system must be clean to
provide good operation and durability. Periodic main­
tenance is necessary. Replace the PCV valve. Re­
move residual combustion deposits from the hoses and throttle body/intake manifold passages.
The PCV valve should be replaced and the system
should be serviced at the interval specified in main­
tenance schedule. If a vehicle is routinely used for short trips, the crankcase ventilation system could
possibly require more maintenance.
CRANKCASE AIR INLET FILTER
MAINTENANCE SCHEDULE Replace or clean, the air inlet filter at the interval
specified in maintenance schedule.
More frequent PCV system maintenance could be
required for:
• Vehicles routinely used for short trips
• Vehicles routinely involved in stop and go traffic
operation
• Vehicles routinely involved in extended periods of
engine idle
MAINTENANCE Clean and lubricate the crankcase air inlet filter
according to the following procedure. (1) Disconnect the fresh air hose from the port on
the crankcase air inlet filter housing (Fig. 8).
(2) Remove the air filter housing from the cylinder
head cover (Fig. 8). Clean the filter in kerosene or a similar solvent.
(3) Lubricate the filter by inverting the housing
and filling it with SAE 30 viscosity engine oil.
(4) Insert the air filter housing nipple in the cylin­
der head cover grommet. Connect the fresh air hose
to the upper port (Fig. 8).
J9000-52

Fig.
8
Crankcase
Air Inlet
Filter
THROTTLE CONTROL LINKAGE

Transmission linkage pivot pin areas (Fig. 9),
should be serviced. The areas lubricated every second
oil change with a multi-purpose lubricant (NLGI GC-
LB).

PIVOT
AREAS
Fig.
9
Transmission
Linkage
Pivot Areas

FUEL
SYSTEM

INSPECTION The fuel system filler cap, nozzle, tubes, hoses, and
connections should be inspected periodically.
FUEL FILTER The fuel filter requires service only when a fuel
contamination problem is suspected. For proper diag­
nosis and service procedures refer to Group 14, Fuel
System.
GASOLINE ENGINE FUEL REQUIREMENTS All gasoline engines require fuel that has a mini­
mum octane rating of 87 determined by the (R +
M)/2 calculation method.
The use of a brand of unleaded gasoline that con­
tains additives is recommended. Gasoline with addi­
tives will improve fuel economy and reduce emissions.

ALCOHOL/GASOLINE
BLENDS
Many brands of blended unleaded gasoline am now
available. Unleaded gasoline is blended with oxygenated-type
fuels to produce a clean air gasoline in many areas.
The use of this type of blended fuel is recommended.
ETH ANOL—Unleaded gasoline and ethanol
blended fuels are a mixture of 10 percent ethanol and 90 percent unleaded gasoline. This is an accept­
able blend of fuel.
MTBE— MTBE blended fuels are a mixture of un­
leaded gasoline and up to 15 percent MTBE (Methyl
Tertiary Butyl Ether). Unleaded gasoline blended
with MTBE is acceptable.

0
- 32
LUBRICATION
AND
MAINTENANCE

•

Fig.
5 Parking Brake Ratio Lever Lubrication (2) Note any indication of brake overheating,
wheel dragging or the vehicle pulling to one side.
(3) Evaluate any performance complaints received
from the owner/operator. (4) Repair the brake system as necessary (refer to
Group 5—Brakes for additional information and ser­
vice procedures).

BODY
COMPONENT
MECHANISMS
LUBRICATION REQUIREMENTS
All operating mechanisms and linkages should be
lubricated when necessary. This will maintain ease of operation and provide protection against rust and
excessive wear. The door weatherstrip seals should
be lubricated to prolong their life as well as to im­ prove door sealing.

LUBRICANT SPECIFICATIONS
All applicable exterior and interior vehicle operat­
ing mechanisms should be:
• Inspected • Cleaned
• All the pivoting/sliding contact areas on the mech­ anisms should then be lubricated.
MOPAR®Multi-Mileage Lubricant or an equiva­
lent, should be used to lubricate the mechanisms.
The door weatherstrip seals should be lubricated
with silicone lubricant spray. Refer to the Body Lu­
bricant Specifications chart below for additional lu­
bricant applications.

LUBRICATION
(1) When necessary, lubricate the cab and cargo
box operating mechanisms with the specified lubri­
cants.

(2) Apply silicone lubricant to a cloth and wipe it
on door seals to avoid over-spray that can soil pas­
senger clothing. (3) Before applying lubricant, the component
should be wiped clean. After lubrication, any excess
lubricant should be removed.
(4) The hood latch, latch release mechanism, latch
striker and safety latch should be lubricated periodi­
cally.
(5) The door lock cylinders should be lubricated 2
times each year (preferably autumn and spring): • Spray a small amount of lock cylinder lubricant di­
rectly into the lock cylinder
• Apply a small amount to the key and insert it into
the lock cylinder • Rotate it to the locked position and then back to
the unlocked position several times
• Remove the key. Wipe the lubricant from it with a
clean cloth to avoid soiling of clothing.

TIRES
RECOMMENDED MAINTENANCE
The condition of the tires should be inspected. The
inflation pressures tested/corrected at the same time as the engine oil is changed and the oil filter is re­
placed.
The tires/wheels should be rotated periodically to
ensure even tread wear. The tires/wheels should be
rotated at the first 12 000 km (7,500-miles) interval.
Thereafter, at each 24 000 km (15,000-miles) inter­
val.
INSPECTION
Inspect the tires for excessive wear, damage. Test
the tires for the recommended inflation pressure and adjust the pressure accordingly. Refer to the tire in­
flation pressure decal located on the left door face. Also to Group 22—Tires And Wheels for tire pres­sure charts, tire replacement, and treadwear indica­

tors.

ROTATION
Tires/wheels should be rotated according to the rec­
ommended interval. The first tire/wheel rotation is
the most important for establishing the prevention of uneven tread wear. After rotation, adjust the tire in­
flation pressure to the air pressure recommended on
the decal located on the left door face.
Refer to Group 22—Tires And Wheels for the rec­
ommended method of tire/wheel rotation.

HEADLAMPS

MAINTENANCE SCHEDULE
Every six months check the headlamp beams to en­
sure that the headlamp beams are correctly posi­
tioned.

AIM
ADJUSTMENT
Refer to Group 8L—Lamps for headlamp aim ad­
justment procedures.

2
- 26
FRONT
SUSPENSION
AND
AXLE

•

Fig.
29
Lower
Ball
Stud
Installation

(3) Thread new sleeve into the upper yoke with
Wrench C-4169 (Fig. 25). Allow two threads to re­
main exposed at the top.
(4) Position steering knuckle on the yoke arms. In­
stall a new lower ball stud nut and tighten to 108
Nnn (80 ft. lbs.) torque.
(5) Tighten the sleeve in upper yoke arm to 54 N*
(40 ft. lbs.) torque with Wrench C-4169.
(6) Install the upper ball stud nut and tighten to
136 Nnn (100 ft. lbs.) torque. Tighten the nut until C-4212-L
C-4288-1

J9202-90

Fig.
30 Upper
Ball
Stud
Installation
the cotter pin can be installed. Do not loosen the nut
to align the hole and the slot. Install a new cotter
pin.

VACUUM
SHIFT
MOTOR
VACUUM
CONTROL
SYSTEM
(FIG. 31) The disconnect axle control system consists of;
• Vacuum control switch on the transfer case • Air vent filter
• Shift motor
• Indicator switch
• Vacuum switch
• Two check valves • And a harness Refer to Group 21, Transmissions for addi­
tional information.

•

COOLING
SYSTEM
7 - 35

HOSE
CLAMP TOOL
6094
HOSE

CLAMP

J9207-36
Fig.
48
Hose
damp Tool

TRANSMISSION
OIL
COOLER—EXCEPT DIESEL
The automatic transmission oil is cooled when it
passes through a cooler in the radiator lower tank (Fig. 49 and 50).

h*-TRANSMISSION

- OIL
COOLER

FRONT
OF
VEHICLE
AUTOMATIC

TRANSMISSION
PRESSURE
LINE
6 AND
8
CYLINDER ENGINE

RETURN
LINE
RY402

Fig.
49 Top View of
Transmission
Oil
Cooling
Circuit—Except Diesel—Typical

COOLING
TUBE (CUT-A-WAY)

DRAIN
COCK
HOSE

CLAMP
HOSE
TO

COOLER
LINE
HOSE
TO

COOLER
LINE

RY401

Fig.
50 Automatic
Transmission
Oil Cooler—Except
Diesel—
Typical

In case of a leak in the transmission oil cooler, en­
gine coolant may become mixed with transmission
fluid or transmission fluid may enter engine cooling system. Both cooling system and transmission should
be drained and inspected in the event cooler is leak­ ing.
REPLACING
OIL
COOLER
IN
BOTTOM
TANK

Remove radiator. Refer to Radiator removal in this
group. The servicing should be performed by a qual­
ified repair facility.
Once the repaired or replacement radiator has been
installed, fill the cooling system and inspect for

leaks.
Refer to Refilling Cooling System and Testing Cooling System For Leaks sections in this group. If
the transmission operates properly after repairing
the leak, drain the transmission and remove the
transmission oil pan. Inspect for sludge and/or rust. Inspect for a dirty or plugged inlet filter. If none of
these conditions are found, the transmission and
torque convertor may not require reconditioning. Re­
fer to Group 21 for automatic transmission servicing.

1RANSMISSI0N
OIL
COOLER-DIESEL
The transmission oil cooler is mounted to a bracket
on the turbocharger side of the engine (Fig. 51).

TRANSMISSION
OIL
COOLER
Fig.
51 Automatic
Transmission
Oil Cooler—5.9L

Diesel
REMOVAL

In case of a leak in the transmission oil cooler, en­
gine coolant may become mixed with transmission
fluid or transmission fluid may enter engine cooling system. Both cooling system and transmission should
be drained and inspected in the event cooler is leak­ ing. (1) Disconnect negative battery cable at battery.
(2) Drain cooling system. Refer to Draining Cool­
ing System. (3) Disconnect coolant lines from cooler.
(4) Disconnect transmission oil lines from cooler.
Plug cooler lines to prevent oil leakage. (5) Remove oil cooler mounting straps.
(6) Lift oil cooler off of mounting bracket.

INSTALLATION
(1) Position oil cooler on bracket.
(2) Install mounting straps.
(3) Connect transmission oil lines to cooler.