wheel FIAT 127 1979 2.G User Guide

Fiat 127 Internet Fan Club (http://fiat127.okruhy.cz) Fiat 127 - 1050
28/34



3.78 Setting the belt tensioner


3.84 Checking a valve clearance


3.87 Made-up tool for depressing tappet buckets


when initially inserted; then reinsert it into the
engine. Ideally the contact points should be just
breaking with the rotor opposite the correct
numbered terminal in the cap. If this is not the
case, repeat on a trial and error basis until this
is
achieved (photo).
69 Fit the clamp washer and nut and lightly
tighten temporarily.
70 With a lamp and battery across the contact
breaker points and the clamp nut just loosened,
move the distributor body round its axis until the
light just goes out. Tighten the clamp nut to the
specified torque load (photo).
Toothed drivebelt - removal, refitting and
adjusting
Note: If adjustment is necessary on an old belt
or if the belt is removed for any reason, always
change the belt for a new one, never adjust
using the old belt.
71 The toothed drivebelt should be renewed at
36 000 miles (60 000 km). This can be done with
the engine in the car. 72 Using a spanner on the
crankshaft pulley nut turn the engine over until
the timing mark on the crankshaft pulley is
aligned with the TDC pointer (long one).
73 Remove the drivebelt cover and the
alternator/water pump drivebelt.
74 Check that the camshaft pulley timing hole is
aligned with the cast ridge on the seal housing;
refer to paragraph 59 of this Section. If it isn't,
turn the engine over one revolution to get it lined
up.
75 Before removing the drivebelt it must be
remembered that neither the camshaft nor the
crankshaft must be moved with the belt off, If
this precaution is not observed the pistons and
valves could impact causing serious damage.
76 Release the tension on the drivebelt by
slackening the bolt in the kidney-shaped slot on
the tensioner bracket, loosening the other
(pivot) bolt, pushing the tensioner wheel against
the spring unit and tightening both bolts. Slide
the drivebelt off the pulleys.
77 Fit the new belt. Start at the crankshaft drive
pulley and, taking care not to kink or strain the
belt, ease it into place over the auxiliary shaft
pulley and the camshaft pulley. It might be
necessary to slightly turn the camshaft to get the
belt to mesh. This should always be done in the
direction of least movement to achieve a mesh,
Fit the belt on the tensioner pulley last. If this is
difficult do not lever or force the belt on but
recheck it and try again (photo).

Fiat 127 Internet Fan Club (http://fiat127.okruhy.cz) Fiat 127 - 1050
29/34

78 Slacken the tensioner bolts to tension the belt
and retighten the bolts (photo).
79 Turn the engine over for two complete
revolutions to even out belt tension. Then again
slacken the tensioner bolts to let the tensioner
take up any slack and
retighten the bolts. Never
turn the engine backwards or rock the camshaft
when tensioning the belt, as slack could develop
in the belt and it might jump a tooth.
80 Refit and tension the alternator/water pump
V-belt. Refit the drivebelt cover.
Valve clearances - adjustment
81 Checking the valve clearances should be
done at the 6000 miles servicing, or whenever
the cylinder head has been removed and
refitted for any reason. It is important that the
clearances are set correctly, otherwise the
timing will be wrong and the engine
performance will be poor. If there is no
clearance at all, the valves and seats will soon
get burnt. Set the clearances with the engine
cold.
82 Remove the camshaft cover. The engine can
be turned over by either using a spanner on the
crankshaft pulley nut, or by jacking up a front
wheel, engaging top gear and using the wheel
to turn the engine.
83 Each tappet must be checked when its
operating cam is pointing upwards, 1800 away
from the tappet. Check the clearances in the
firing order, No. 1 cylinder first and then 3, 4
and 2. Do the exhaust of one cylinder and the
inlet of the one after, at the same time to
minimise the amount of engine turning. Counting
from the timing belt end, exhaust valves are
1-4-5-8, inlet valves 2-3-6-7.
84 Insert the feeler gauge for the appropriate
valve. See the Specifications for correct
settings. The feeler should slide in readily
between cam and shim, but with slight frictional
drag. Try one a size thicker and one a size
thinner. The thick one should not go in and the
thinner one should be too loose (photo).
85 If the clearance is wrong, measure the
clearance and write it down with the number of
the valve. When all the clearances have been
checked, it will be necessary to remove those
shims which are fitted where the clearances are
wrong, and renew them with different thickness
shims. If a clearance is too big, use a thicker
shim. If a clearance is too small use a thinner
shim. Calculate by simple subtraction. 86 To change a shim, turn the engine until the
relevant cam is pointing upwards, then turn the
tappet in its housing so that the slot in the rim is
accessible.
87 The manufacturer provides special tools for
depressing tappets (Nos. A60480 and A60443).
These make the job easier if they can be
borrowed, but it is possible to do the job without
them. The best way is to make up a tool from a
piece of steel plate shaped as shown in the
photograph. Alternatively use a screwdriver to
lever the tappet down and another on
e, on edge,
to hold the tappet down by positioning it
between the camshaft and the rim of the tappet;
then remove the lever. This is quite tricky and
needs some care to avoid any damage. If in any
doubt about doing this job it should be left to a
FIAT agent. As well as having the right tools he
will also have a stock of shims from which to
choose those required to correct wrong
clearances. It is expensive buying shims that are
not required (photo).
88 With the tappet held down, prise the shim out
with a thin screwdriver. The FIAT way is to lift
the shim using compressed air, which is
effective if an air line is available. The shims are
held in quite strongly by the oil film and they
must be lifted up square or they will jam.
Remove the shim with long-nosed pliers
(photos).
89 When new, shims have their thickness
marked in millimetres on their undersides. This
marking may wear off and then it will be
necessary to measure their thickness with a
micrometer. From the thickness of the shim and
the error in the clearance, calculate the size of
shim required to produce the correct clearance.
90 Insert the new shim, numbered side down
towards the tappet. Remove the tools used for
depressing the tappet and repeat the operation
until all clearances are correct.
91 Using clean engine oil lubricate all moving
and sliding parts in the camshaft/tappet
assembly. Fit a new gasket and refit the
camshaft cover together with the nine bolts and
washers. Tighten the bolts progressively (photo).


Engine - final assembly
92 Completing assembly of the 1049 cc engine
follows broadly the procedure for that of the
smaller engine which is dealt with in Chapter 1,
Section 56.
93 The manifold gasket is supplied in two parts
for the 1049 cc engine (photo). These serve