key FIAT 500 ABARTH 2012 2.G Blue And Me Owner's Manual

Accessing the Image ID
To access the Image ID by manual interaction, proceed as
follows:
Select Image ID and then press thePRESET UP/OK
button.
The instrument panel display will show your
BLUE&ME™Image ID code.
Accessing the Application ID
To access the Application ID by manual interaction,
proceed as follows:
Select Application ID and then press thePRESET UP/OK
button.
The instrument panel display will show your
BLUE&ME™Application ID code.
Accessing the device ID
To access the device ID by manual interaction, proceed as
follows:
Select device ID and then press thePRESET UP/OK
button.
The instrument panel display will show your
BLUE&ME™device ID.
Media Player Settings
Autoplay
When the Autoplay option is on,BLUE&ME™will start
to play the audio files on your USB device as soon as you
turn the ignition key ON. Once you activate this option,
the first time you use the player, playback will start
automatically.
66 BLUE&ME™ User’s Manual

LIST OF AVAILABLE VOICE COMMANDS
The following tables list the voice commands available
onBLUE&ME™Hands-Free Communication. Thekey-
wordfor each voice command (e.g., the main voice
command) and the synonyms that may be used are
shown.
74 BLUE&ME™ User’s Manual

Problem Probable Cause Possible Solution
Display screen shows:
NO PHONE
And the system says
“No Bluetooth telephone
is connected.”•The paired mobile phone is turned off
•The paired mobile phone is not within
range of the system (the mobile phone
should be located within approximately
30 feet of the system)
•Bluetoothwireless technology connec-
tion has been disabled on your mobile
phone•Turn the paired mobile phone on
•Make sure that your phone is paired
•Make sure that theBluetoothwireless
technology connection on your mobile
phone is enabled
•Make sure that the mobile phone you
paired with the system is within range
Problem Probable Cause Possible Solution
Display screen shows:
DISCONNECTED.•A technical error occurred with the mo-
bile phoneBluetoothwireless technol-
ogy capabilities
•During an ongoing phone conversation,
the mobile phone was taken out of the
system range•ResetBLUE&ME™by turning the mo-
bile phone off and on
•ResetBLUE&ME™by turning the igni-
tion key to OFF and then to ON again
1
BLUE&ME™ User’s Manual 85

Problem Probable Cause Possible Solution
Display screen shows:
ONLY AT REST and the
system says: “This com-
mand is available only
when the vehicle is sta-
tionary.”•Even occasional short viewings of the
car display may be hazardous if your
attention has been diverted away from
your driving tasks. Certain
BLUE&ME™functions, which require
the user to give attention to the car dis-
play, are only available when the car is
stopped•Stop your car and attempt to perform the
function again manually, or continue driving
and perform the function using the voice rec-
ognition system
The system did not re-
spond to voice com-
mand or key press•If you do not speak soon enough after
pressing the
button, the system
will interrupt voice interaction If you
are speaking too far from the in-car mi-
crophone (for example, if you are sitting
in the back seat), the system may not
hear your voice command
•If you don’t wait for the tone after
pressing the
button, the system
will get only a portion of the keyword
and will not recognize it•Press the
button and pronounce the
voice command again
•Press the
button and pronounce the
voice command again
•Press the
/MAINbutton and try the op-
eration again. Make sure to take action
within approximately eight seconds after
pressing the
/MAINbutton
1
BLUE&ME™ User’s Manual 87

Problem Probable Cause Possible Solution
•If you don’t press the
button be-
fore pronouncing a voice command, the
system will not activate voice recogni-
tion and therefore will not recognize
your voice commands
•If you don’t press the
/MAINbut-
ton to enter the Main Menu, it will not
be possible to manually access the
BLUE&ME™menu
•If after pressing the
/MAINbutton,
you don’t take action within approxi-
mately eight seconds, the system will
not respond to your key press
The mobile phone
prompts you to enter a
PIN number, but no
phone pairing proce-
dure was running•After you delete the pairing-related user
information on your mobile phone or
on the system, theBluetoothpairing
relationship between your mobile phone
andBLUE&ME™will no longer work•
Select option DELETE USERS on the system
and delete all users; then, pair the phone
again – see the section SETTING FUNCTIONS
- MANAGING USER DATA AND PHONE-
BOOK and also the section SETTING FUNC-
TIONS - PAIRING YOUR MOBILE PHONE
88 BLUE&ME™ User’s Manual

Problem Probable Cause Possible SolutionWhen in close proximity of the car,
answering a phone call directly
using the mobile phone “answer”
button, will automatically activate
the hands-free communication
function (the caller ’s voice is
played through the car speakers)•Some types of mobile phones re-
quire you to set the phone to
choose between automatic incoming
call transfer to the system or non-
automatic incoming call transfer
(you will transfer the call using the
mobile phone keypad, as required)•Refer to your mobile phone owner ’s
manual to find out how to set up
the default location for phone audio
when a phone call is received
Pairing a paired mobile phone,
the display screen shows: Pair.
failed and the system says “Pair-
ing unsuccessful. Please try
again.”•Before re-pairing with a mobile
phone, information from the previ-
ous pairing onBLUE&ME™must
be deleted•Remember that the pairing proce-
dure will only need to be per-
formed once for your mobile phone.
After this procedure,BLUE&ME™
will automatically connect to your
phone each time you get into the
car and turn the ignition key to ON
•To pair the phone again, select DE-
LETE USERS and then re-pair the
phone – see the section SETTING
FUNCTIONS - MANAGING USER
DATA AND PHONEBOOK and also
the section SETTING FUNCTIONS -
PAIRING YOUR MOBILE PHONE1
BLUE&ME™ User’s Manual 89

Media Player
Problem Probable Cause Possible Solution
Displayed message: NO MEDIA
andBLUE&ME™says: “No media
found”•No USB device is connected to the
USB port in the car
•No digital audio files are stored
on the USB memory device
•If power is interrupted, (e.g., car
battery disconnection),
BLUE&ME™will rebuild the me-
dia library•Connect your USB device to
BLUE&ME™
•Store digital audio files on your
USB memory devices following
the instructions given by your
media file software
•Remove the USB device from the
USB port and replace it to rebuild
the media library again
•Check whether your USB device
is supported byBLUE&ME™
After connecting your USB device
and turning the ignition key to ON,
no music is played•Autoplay may be set to off•Set Autoplay to on, remove and
then replace the USB device
•Press the
button and say
“PlayMedia playback should
start
94 BLUE&ME™ User’s Manual

Problem Probable Cause Possible Solution
After inserting a USB device and
turning the car key to the ON posi-
tion,BLUE&ME™malfunctions
occur. (e.g., failure to reproduce mu-
sical tracks or no voice messages)•You may have used a USB device
with the PASSWORD function
enabled•Use another USB device without a
password protection function
Problem Probable Cause Possible Solution
Displayed message: NO PLAY-
LISTS andBLUE&ME™says: “No
playlist found”•No playlist is stored on the USB
device connected•Build a playlist on your computer
using your media file software and
then copy it to your USB device
Displayed message: PLAYLIST ER-
ROR andBLUE&ME™saysPlay-
list error”•Playlist is damaged or invalid•Make sure the playlist is in.m3u
or.wpl format
•Build the playlist again following
the instructions given in BUILDING
PLAYLISTS FORBLUE&ME™-
PRACTICAL HINTS
•If the problem persists, delete the
playlist from your USB device
1
BLUE&ME™ User’s Manual 95

Problem Probable Cause Possible Solution
After saying a command,
BLUE&ME™says: “Command
not available”, although the com-
mand you prompt is a first level
voice command•Certain commands are not avail-
able when the track is paused or
the CD player is playing a track•If the track is paused, resume play-
back by pressing the
/ESCbut-
ton. Then pronounce the voice
command again
The same USB memory device
previously connected takes more
than 10 seconds to restart play-
back onBLUE&ME™•You removed the USB memory de-
vice from the PC before it was
ready•To reset the USB memory device
using MicrosoftWindowsXP,
click on My Computer in the Start
menu, click rightward on the USB
memory device, select Properties,
select Tools, click on key “Check
Now...” in field “Error-checking”,
select “Automatically fix file sys-
tem errors” and then click Start
•To avoid future problems, remove
the USB device using the option
“Secure hardware removal”
98 BLUE&ME™ User’s Manual