front light FIAT PUNTO EVO 2010 1.G Manual PDF

228
F0U0289mfig. 211
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Remember that the car’s road holding de-
pends on correct tyre pressures
WARNING
If the pressure is too low, the tyre will over-
heat and could be seriously damaged.
WARNING
Avoid switching the tyres from the right
side of the vehicle to the left side and vice
versa.
Do not re-spray alloy wheel rims at temperatures
higher than 150°C. The mechanical characteris-
tics of the wheels may be compromised.
WARNING
❒check the tyres regularly for cuts on the sides, swelling
or irregular tread wear. Go to a Fiat Dealership if re-
quired;
❒avoid overloading the car when travelling: this may cause
serious damage to the wheels and tyres;
❒if a tyre is punctured, stop the vehicle immediately and
change it to avoid damage to the tyre, the rim, and the
suspension and steering systems;
❒a tyre will age even if it is not used much. Cracks in
the tread and on the sidewalls are a sign of ageing. In
any event, have the tyres checked by specialised per-
sonnel if they have been fitted for longer than 6 years.
Remember to check the spare wheel very carefully;
❒in case of replacement, always fit new tyres, avoiding
those with an unknown origin;
❒if a tyre is replaced, you should also change the inflation
valve;
❒to allow even wear between the front and rear tyres,
it is advisable to switch them every 10-15 thousand kilo-
metres, keeping them on the same side of the car so
as not to reverse the direction of rotation.
211-234 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 228

233
INTERIOR
Check regularly that water is not trapped under the mats
(due to drops from shoes, umbrellas, etc.), as this could
cause the sheet metal to rust.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Detergents cause water pollution. The ve-
hicle should be washed only in areas
equipped for collecting and purifying the
liquids used in the washing process.
Windows
Use specific detergents to clean the windows.
Also use clean cloths to avoid scratching the glass or al-
tering the transparency.
IMPORTANT Wipe the rear window gently with a cloth
in the direction of the filaments to avoid damaging the heat-
ing device.
Engine compartment
Wash the engine compartment thoroughly at the end of
every winter. Be careful not to direct the jet of water on-
to electronic control units. Adequately protect the up-
per air vents to prevent damage to the windscreen wiper
motor. Have this operation performed at a specialised
workshop.
IMPORTANT The washing should take place with the en-
gine cold and the ignition key in the STOP position. After
the wash, make sure that the various protective devices
(e.g. rubber caps and guards) have not been removed or
damaged.
Front headlights
IMPORTANT Never use aromatic substances (e.g. petrol)
or ketenes (e.g. acetone) for cleaning the plastic lenses of the
front headlights.
Never use flammable products, such as
petroleum ether or modified petrol, to
clean inside the car. The electrostatic charges
which are generated by rubbing during cleaning
may cause a fire.
WARNING
Do not keep aerosol cans in the vehicle:
these could explode. Aerosol cans must
not be exposed to temperatures exceeding 50°C.
When the vehicle is exposed to sunlight, the tem-
perature inside can greatly exceed this value.
WARNING
211-234 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 233

F0U0294mfig. 216
H Maximum authorised weight on rear axle.
I Engine type.
L Bodywork version code.
M Number for spare parts.
N Correct value of smoke coefficient (for diesel engines).
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
235
TECHNICAL SPECIFICATIONS
IDENTIFICATION DATA
We recommend taking note of the identification codes.
The following identification codes are printed and
shown on the plates:
❒Vehicle identification number (VIN) plate.
❒Chassis marking.
❒ Bodywork paint identification plate.
❒Engine marking.
VIN PLATE fig. 216
The plate can be found on the left side of the boot floor
and it bears the following identification data:
B Type-approval number.
C Vehicle type identification code.
D Chassis manufacturing serial number.
E Maximum authorised weight of vehicle fully laden.
F Maximum authorised weight of vehicle fully laden plus
trailer.
G Maximum authorised weight on front axle.
235-258 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 235

F0U0295mfig. 217F0U0296mfig. 218
ENGINE MARKING
This is printed onto the cylinder block and shows the type
and production serial number. BODYWORK PAINT IDENTIFICATION
PLATE fig. 217
This can be found on the external rear door pillar (left-
hand side) and it bears the following information:
A Paint manufacturer.
B Colour name.
C Fiat colour code.
D Re-spray and touch-up colour code.
CHASSIS MARKING fig. 218
This is printed on the passenger compartment floor,
near the right front seat.
❒vehicle type (ZFA 199000);
❒chassis serial number.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
236
235-258 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 236

KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
240
Self-adjusting with no free travel
Front
Five forward gears plus reverse
with synchronisers for selecting
forward gears
Electronically controlled
phased sequential multipoint
electronic injection
with turbo and intercoolerCommon Rail Multijet
direct injection
Modifications or repairs to the fuel supply system that are not carried out properly or do not
take the system’s technical specifications into account can cause malfunctions leading to the
risk of fire.
WARNING
Multipoint electronic
injection
Six forward gears plus
reverse
with synchronizers for
selecting
forward gearsFive or six forward
gears plus reverse
with synchronisers for
selecting forward
gears
FUEL SUPPLY
1.2 – 1.4 – 1.4 Multi Air 1.4 Turbo Multi Air 1.3 Multijet – 1.6 Multijet
Fuel
supply
TRANSMISSION
1.2 1.4–1.4 Turbo 1.3 Multijet 75HP 1.3 Multijet 90HP1.4 Multi AirMulti Air 1.3 Multijet 95HP 1.6 Multijet
Gearbox
Clutch
Traction
235-258 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 240

KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
241
rack and pinion with electric power steering
10.9
Independent wheel
McPherson-typeIndependent wheel McPherson-type with anti-roll bar
self-ventilated discs
drum or disc (for versions/markets where provided)
controlled by hand lever, acting on rear brakes
Torsion beam with interconnected wheels
BRAKES
Service brakes: front
rear
Parking brake
IMPORTANT Water, ice and salt on the roads may deposit on the brake discs, reducing braking efficiency the first time the
brakes are applied.
SUSPENSIONS
1.2 – 1.4 1.4 Multi Air – 1.4 Turbo Multi Air – 1.3 Multijet – 1.6 Multijet
Front
Rear
STEERING SYSTEM
Type
Turning circle (kerb to kerb) m
235-258 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 241

KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
242
F0U0193mfig. 219
WHEELS
RIMS AND TYRES
Pressed steel or alloy rims. Tubeless radial carcass tyres.
All approved tyres are listed in the Log Book.
IMPORTANT In the event of discrepancies between the in-
formation provided in this Owner Handbook and the Log
Book, the latter takes precedence.
To ensure driving safety, ensure that tyres of the same
make and type are fitted on all wheels.
IMPORTANT Do not use inner tubes with tubeless tyres.
SPARE WHEEL
Pressed steel rim
Tubeless tyre.
WHEEL GEOMETRY
Total front toe in: + 1 ± 1 mm
Total rear toe in: + 1.7 ± 2 mm
The values refer to the car in running order.CORRECT READING OF THE TYREExample: 175/65 R 15 84T
175 = Nominal width
(S, distance in mm between sidewalls).
65 = Height/width ratio (H/S) as a percentage.
R = Radial tyre.
15 = Rim diameter in inches (Ø).
84 = Load index.
T = Maximum speed index.
235-258 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 242

KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
245
––
––
––
––
2.4 2.2
2.6 2.2
––
––
2.4 2.2
2.6 2.4
––
––
2.6 2.3
2.8 2.52.2 2.1
2.2 2.2
2.2 2.0
2.2 2.2
––
––
––
––
2.2 2.0
2.2 2.2
––
––
2.4
(Õ)2.2(Õ)2.4(Õ)2.4(Õ)
––
––
––
––
2.2 2.0
2.2 2.2
––
––
2.2 2.0
2.2 2.2
––
––
2.4 2.2
2.4 2.4––
––
––
––
2.2 2.0
2.2 2.2
2.2
(❒)2.0 (❒)2.2 (❒)2.2 (❒)
2.2 2.0
2.2 2.2
2.2
(❒)2.0 (❒)2.2 (❒)2.2 (❒)
2.4 2.2
2.4 2.4
2.4 2.1
2.5 2.2
2.3 2.1
2.3 2.3
––
––
––
––
2.3 2.1
2.4 2.4
––
––
2.4 2.2
2.5 2.4––
––
2.3 2.1
2.3 2.3
––
––
––
––
2.3 2.1
2.4 2.4
––
––
2.4 2.2
2.5 2.4
COLD TYRE PRESSURE (bar)
Versions1.2 – 1.41.4 Multi Air 1.4 Turbo Multi Air1.3 Multijet 75HP 1.3 Multijet 90HP 1.6 Multijet
1.3 Multijet 95HP
Front Rear Front Rear Front Rear Front Rear Front Rear Front Rear
175/65 R15 84T
Medium load
Full load
185/65 R15 88T
Medium load
Full load
185/65 R15 88H
Medium load
Full load
185/65 R15 88V
Medium load
Full load
195/55 R16 87H
Medium load
Full load
195/55 R16 87V
Medium load
Full load
205/45 R17 88V
Medium load
Full load
(❒) SPORT configuration (Õ) Tyre provided only for 1.4 engine
Add +0.3 bar to the prescribed inflation pressure when the tyres are warm. However, recheck that the value is correct with the tyre cold. With snow
tyres, add +0.2 bar to the pressure recommended for standard tyres. When running at speeds higher than 160 km/h, inflate tyres to full-load pres-
sures. If there is a TPMS system, add +0.1 bar to the prescribed pressure. 175/65 R15 84T tyres do not come with a TPMS system.
235-258 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 245

KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
248
3 doors
5 seats
1015
560
850
850
1575
900
400
50
60
5 doors
5 seats
1030
560
850
850
1590
900
400
50
60
3 doors
5 seats
1025
560
850
850
1585
1000
400
50
60
3 doors
5 seats
1060
1155
(❒)
560
850
850
1715 (❒)/
1620
1000
400
50
60
5 doors
5 seats
1075
1170
(❒)
560
850
850
1730 (❒)/
1635
1000
400
50
60
5 doors
5 seats
1040
560
850
850
1600
1000
400
50
60
WEIGHTS
Petrol versions 1.2 1.4 1.4 MultiAir
Weights (kg)
Unladen weight
(with all fluids,
fuel tank filled to 90%
and without
optional equipment):
Payload (*)
including the driver:
Maximum permitted
loads (**)
– front axle:
– rear axle:
– total:
Towable loads:
– braked trailer:
– non-braked trailer:
Maximum load on roof:
Maximum load on the
ball joint (braked trailer):
(*) If special equipment is fitted (sunroof, tow hitch, etc.) the unladen car weight increases, thus reducing the specified payload
with respect to the maximum permitted load.
(**) Loads that must not be exceeded. The driver is responsible for arranging goods in the boot and/or on the load carrying
platform within the maximum permitted loads.
(❒) 1.4 Turbo Multi Air configuration.
235-258 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 248

KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
249
3 doors
5 seats
1090
560
950
850
1650
1000
400
50
60
5 doors
5 seats
1105
560
950
850
1665
1000
400
50
60
3 doors
5 seats
1130
560
950
850
1690
1000
400
50
60
5 doors
5 seats
1145
560
950
850
1705
1000
400
50
60
3 doors
5 seats
1190
560
1000
850
1750
1000
400
50
60
5 doors
5 seats
1205
560
1000
850
1765
1000
400
50
60
Multijet versions 1.3 Multijet 75HP 1.3 Multijet 90HP 1.6 Multijet
1.3 Multijet 95HP
Weights (kg)
Unladen weight (with all
liquids, fuel tank filled
to 90% and without
optional equipment):
Payload (*) including the
driver:
Maximum permitted
loads (**)
– front axle:
– rear axle:
– total:
Towable loads:
– braked trailer:
– non-braked trailer:
Maximum load on roof:
Maximum load on the ball
joint (braked trailer):
(*) If special equipment is fitted (sunroof, tow hitch, etc.) the unladen car weight increases, thus reducing the specified payload
in relation to the maximum permissible loads.
(**) Loads that must not be exceeded. The driver is responsible for arranging the goods in the boot and/or on the load carrying
platform
within the maximum permitted loads.
235-258 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 249