wipers FORD ASPIRE 1996 1.G Owners Manual

42
*
[ST02100(ALL)09/93]
LOCK locks the steering wheel. It also locks the
gearshift lever in P (Park) (automatic transaxle).
*
[ST02200(ALL)01/95]
LOCK is the only position that allows you to
remove the key. The LOCK feature helps to
protect your vehicle from theft.
*
[ST02300(ALL)05/95]
If your key is stuck in the LOCK position and
will not turn, move your steering wheel left or
right until the key turns freely.
[ST02325(ALL)09/93]
If your vehicle has a manual transaxle, you must
push the key toward the steering column to
rotate the switch to the LOCK position.
%*
[ST02350(ALL)03/95]
ACC (accessory) allows some of your vehicle's
electrical accessories such as the radio and the
windshield wipers to operate while the engine is
not running.
*
[ST02400(ALL)05/95]
ON allows you to test your vehicle's warning
lights (except the brake system warning light) to
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
*
[ST02500(ALL)03/95]
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996

85 [SC02900(ALL)07/93]
one third page art:0032175-A
Turn signal
*
[SC03100(ALL)03/95]
Windshield Wipers and Washer
*
[SC03200(ALL)08/91]
To operate the windshield wipers and washers,
make sure your ignition key is turned to the ON
position.
[SC03250(ALL)07/93]
The windshield wipers can be operated by
moving the control lever. The standard wipers
have two speeds and the optional wipers have
three speeds.
[SC03400(ALL)07/93]
To operate the standard wipers, pull the lever
down to the first stop (LO). For high speed
operation, pull the lever down to the second
stop (HI).
[SC03450(ALL)03/94]
The optional wipers have a third position which
provides intermittent wiper operation. For preset
interval intermittent wiper operation, pull the
lever down to the first stop (INT). For normal
operation pull the lever down to the second stop
(LO), or for high operation pull the lever down
to the third stop (HI).
File:07icscf.ex
Update:Wed Jan 24 14:50:00 1996

87 [SC04500(ALL)05/93]
quarter page art:0032178-A
Windshield washer control
[SC04600(ALL)07/93]
If the washer does not work, check the washer
fluid level and fill it if it is low. SeeServicing
Your Aspirelater in the owner guide. If there is
fluid in the reservoir, consult your nearest
authorized Ford dealer.
*
[SC04700(ALL)01/95]
Do not try to clean the windshield when the
washer fluid container is empty or activate the
washers at any time for more than 15 seconds
continuously. This could damage the washer
pump system.
*
[SC04800(ALL)01/93]
RWARNING
In freezing weather, the washer solution
may freeze on the windshield and obscure
your vision. Always warm up the
windshield with the defroster before you
use the washer fluid. If you cannot see
through the windshield clearly, it can
increase the risk of being involved in a
collision.
*
[SC04900(ALL)04/95]
For information about refilling the washer fluid
or replacing your windshield wiper blades, see
Windshield washer fluid and Wipersin the Index.
File:07icscf.ex
Update:Wed Jan 24 14:50:00 1996

88
[SC04920(ALL)02/95]
Rear Windshield Wipers
(If equipped)
[SC04940(ALL)07/93]
The rear window wiper and washer can be
activated by turning the knob at the end of the
wiper/washer lever.
[SC04960(ALL)02/95]
To turn the rear wiper on, turn the knob up to
the ON position.
[SC04980(ALL)02/95]
To wash the rear window, turn the knob up to
thecposition. When you release it, the
washers will stop.
[SC05010(ALL)02/95]
For a single wash/wipe cycle, turn the knob
down to thedposition.
[SC05050(ALL)05/93]
quarter page art:0032205-A
Rear windshield wiper/washer controls
File:07icscf.ex
Update:Wed Jan 24 14:50:00 1996

195
*
[SV21400(ALL)02/95]
Engine coolant refill procedure
*
[SV21500(ALL)03/95]
When the entire engine cooling system is to be
drained and refilled, use the following
procedure:
*
[SV21600(ALL)01/89]
1. Remove the radiator cap.
*
[SV21700(ALL)06/89]
2. With the engine off and cool, add a 50/50
mixture of recommended engine cooling
system fluid and water until the radiator is
full.
*
[SV21800(ALL)07/93]
3. Replace and fully tighten the radiator cap,
then unscrew the cap to the first stop.
*
[SV21900(ALL)06/89]
4. Start and idle the engine until the radiator
upper hose is warm (this indicates the
thermostat is open and engine coolant is
flowing through the entire system).
[SV22000(ALL)03/94]
5. When you are done, stop the engine and
tighten the cap completely.
%*
[SV22100(ALL)11/94]
Checking hoses
*
[SV22200(ALL)01/89]
Check all engine and heater system hoses and
hose connections for deterioration, leaks, and
loose hose clamps as specified in the
maintenance schedule. Repair or replace with
Motorcraft hoses or equivalent as necessary.
*
[SV22300(ALL)03/95]
Windshield Washer Fluid and
Wipers
*
[SV22350(ALL)03/95]
Washer Fluid
*
[SV22500(ALL)01/95]
Check the level of the windshield washer fluid
every time you stop for fuel. The reservoir for
the windshield washer fluid is located in the
engine compartment.
[SV22600(ALL)05/93]
To check the washer fluid level, place your
finger over the hole in the reservoir cap and pull
out the dipstick.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

198 [SV23900(ALL)02/95]This is not the same reservoir your front
windshield wipers use. Refill this reservoir with
the same solution you use for your windshield.
*
[SV24000(ALL)03/95]
Wiper Blades
*
[SV24100(ALL)03/95]
Check the windshield wiper blades at least twice
a year. Also check them whenever they seem
less effective than usual. Substances such as tree
sap and some hot wax treatments used by
commercial car washes reduce the effectiveness
of wiper blades.
*
[SV24200(ALL)03/95]
If the blades do not wipe properly, clean both
the windshield and the wiper blades. Use
undiluted windshield washer solution or a mild
detergent. Rinse thoroughly with clear water. Do
not use fuel, kerosene, paint thinner, or other
solvents to clean your wiper blades. These will
damage your blades.
*
[SV24300(ALL)03/95]
To make reaching the wiper blades easy, simply
turn the ignition to the ACC position and turn
your wipers on. Wait for them to reach a
vertical position and turn the ignition to the OFF
position. Do not move the wipers manually.
Manually moving the wipers across the
windshield may damage them.
*
[SV24400(ALL)03/01]
Wiper blade replacement
*
[SV24500(ALL)01/95]
If the wipers still do not work properly after
you clean them, you may need to replace the
wiper blade assembly. When replacing the wiper
blade assembly always use a Motorcraft part or
equivalent.
*
[SV24525(ALL)10/93]
To replace the wiper blades:
*
[SV24535(ALL)06/95]
1. Pull the wiper arm away from the
windshield and into the lock position.
*
[SV24550(ALL)03/94]
2. Turn the blade at an angle from the wiper
arm. Push the lock pin with a screwdriver to
release the blade and pull the wiper blade
down toward the windshield to remove it
from the arm.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996