ignition FORD TAURUS 1996 Service Manual

198 [DR06789(ALL)04/95]If your gearshift is on the console, you can use
any of the following positions:
% [DR06790(ALL)04/95]
half page art:0001028-D
The console-mounted gearshift
*
[DR06791(ALL)04/95]
The console-mounted gearshift will lock when
you turn the key to the LOCK position. When
the gearshift is in any position except P (Park),
the ignition key cannot be turned to LOCK or
removed from the steering column. TO
REMOVE THE KEY, the gearshift levermustbe
in P (Park).
*
[DR06793(ALL)11/94]
Once the gearshift is secure in the desired
position, release the brake pedal and use the
accelerator as necessary.
%*
[DR06795(ALL)01/95]
R (Reverse)
*
[DR06800(ALL)08/95]
With the gearshift in the R (Reverse) position,
the vehicle will move backward. You should
always come to a complete stop before shifting
into or out of R (Reverse).
File:10fcdrt.ex
Update:Mon Jan 22 15:59:33 1996
ProCarManuals.com

204
*
[DR17600(ALL)05/95]
Each time you turn the ignition key to the ON
position, the ABS will function through one test
cycle. When this happens, the ABS light will
come on for up to five seconds. If the light stays
on longer than five seconds, shut off the engine
and restart. If it remains on, it means the ABS is
disabled and should be serviced immediately to
restore the benefits of the anti-lock feature.
Normal braking is not affected unless the red
BRAKE system warning light is also lit.
*
[DR17650(ALL)05/95]
ABS has self-check capabilities. As described
above, the system turns on the ABS light each
time you start your engine. After the engine is
started and the ABS light turns off, the system
performs another test the first time the vehicle
reaches 4-9 mph (6-15 km/h). The system turns
on the ABS pump motor for approximately 1/2
second. At this time, a mechanical noise may be
heard. This is a normal part of the self-check
feature. If a malfunction is found during this
check the ABS light will come on.
[DR17675(ALL)02/95]
Vehicles with ABS are identified with a label on
the front door pillar.
*
[DR17700(ALL)08/95]
Ford Motor Company has not found any
negative effects of mobile radio transmitting
equipment installed on vehicles with the ABS
system providing that the radio is installed
according to the radio manufacturer's
instructions. However, if you have had a mobile
radio transmitter installed and the ABS light
comes on (at any time other than immediately
after turning the key to the ON position) have
your mobile radio dealer inspect the radio
installation. Also, if the ABS system is activated
other than during maximum braking, have your
mobile radio installation checked.
File:10fcdrt.ex
Update:Mon Jan 22 15:59:33 1996
ProCarManuals.com

218
*
[RE00850(ALL)07/95]
If the acid touches someone's skin, eyes, or
clothing, immediately flush the area with water
for at least 15 minutes. If someone swallows the
acid, have him or her drink lots of milk or water
first, then Milk of Magnesia, a beaten egg, or
vegetable oil. Call a doctor immediately.
*
[RE00900(ALL)03/95]
To avoid damaging your vehicle or your battery,
and to avoid injury to yourself, follow these
directions for preparing your vehicle to
jump-start and connecting the jumper cables in
the order they are given. If in doubt, call for
road service.
*
[RE01000(ALL)03/95]
Preparing Your Vehicle
*
[RE01100(ALL)03/95]
1. Your vehicle has a 12-volt starting system, so
you need to use a 12-volt jumper system.
You will damage your starting motor,
ignition system, and other electrical parts if
you connect them to a 24-volt power supply
(either two 12-volt batteries in series or a
24-volt generator set).
*
[RE01200(ALL)03/95]
2. Do not disconnect the battery of the disabled
vehicle. You could damage the vehicle's
electrical system.
*
[RE01300(ALL)04/95]
3. Park the booster vehicle close to the hood of
the disabled vehicle.Make sure the vehicles
do not touch each other.Set the parking
brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[RE01400(ALL)03/95]
4. Check all battery terminals and remove any
excessive corrosion before you attach the
jumper cables.
[RE01500(ALL)04/95]
5. Turn on the heater fan in both vehicles. If
you have electronic climate control, press the
VF-DEF button. Turn off all other switches
and lights.
File:12fcret.ex
Update:Mon Jan 22 16:01:15 1996
ProCarManuals.com

222
*
[RE04450(ALL)03/95]
If you need to replace your battery, seeBattery
in theServicing Your Vehiclechapter.
%
*
[RE04500(ALL)03/95]
Changing a Tire
*
[RE04600(ALL)01/95]
If you get a flat tire while you are driving, do
not apply the brake heavily. Instead, gradually
decrease the speed. Hold the steering wheel
firmly and slowly move to a safe place on the
side of the road. Park on a level spot, turn off
the ignition, set the parking brake, and turn on
the hazard flashers.
[RE04610(ALL)01/95]
NOTE: Tire sealants that are injected through
the valve stem are not to be used to
service punctured tires because they
can produce wheel rust and tire
imbalance.
%*
[RE04700(ALL)03/95]
The Temporary Spare Tire
*
[RE04800(ALL)03/95]
You may have a high pressure temporary spare
tire. This spare tire is smaller than a regular tire
and is designed for emergency use only. Use it
only when you get a flat tire and replace it as
soon as you can. This spare tire is marked with
the words ªTEMPORARY USE ONLYº so that
you can easily identify it.
*
[RE04900(ALL)01/93]
RWARNING
If you use the temporary spare tire
continuously or do not follow these
precautions, the tire could fail, causing
you to lose control of the vehicle, possibly
injuring yourself or others.
File:12fcret.ex
Update:Mon Jan 22 16:01:15 1996
ProCarManuals.com

235
*
[RE18000(ALL)03/95]
Towing Your Vehicle Behind Another
Vehicle
*
[RE18100(ALL)03/95]
At times, you may want to tow your vehicle
behind another vehicle, such as a recreational
vehicle, a car, or a truck.
*
[RE18200(ALL)03/95]
Before you have your vehicle towed:
*
[RE18300(ALL)03/95]
q
Release the parking brake.
*
[RE18400(ALL)03/95]
q
Move the gearshift to N (Neutral).
[RE18500(ALL)01/95]
q
Turn the key in the ignition to OFF.
*
[RE18600(ALL)03/95]
q
Unlock the steering wheel.
[RE18700(ALL)01/95]
Do not tow your vehicle at a speed faster than
35 mph (56 km/h) or for a distance greater than
50 miles (80 km), unless the drive wheels are
placed on dollies.
*
[RE19000(ALL)08/95]
RWARNING
Never use a tow bar that attaches to the
bumper when you tow your vehicle. This
could damage the bumper and cause an
accident.
File:12fcret.ex
Update:Mon Jan 22 16:01:15 1996
ProCarManuals.com

257 [SV01850(ALL)10/95]
RWARNING
The cooling fans are automatic and may
come on at any time. Always disconnect
the negative terminal of the battery before
working near the fan.
*
[SV01900(ALL)06/95]
q
If you must work with the engine running,
avoid wearing loose clothing or jewelry that
could get caught in moving parts. Take
appropriate precautions with long hair.
*
[SV02000(ALL)06/95]
q
Do not work on a vehicle in an enclosed
space with the engine running, unless you are
sure you have enough ventilation.
*
[SV02100(ALL)08/95]
q
Never get under a vehicle while it is
supported by a jack only. If you must work
under a vehicle, use safety stands.
*
[SV02200(ALL)06/95]
q
Keep all lit cigarettes and other smoking
materials away from the battery and all
fuel-related parts.
*
[SV02250(ALL)03/95]
If you disconnect the battery, the engine must
ªrelearnº its idle conditions before your vehicle
will drive properly. To find out how the engine
does this, seeBatteryin this chapter.
*
[SV02550(ALL)03/95]
Working with the engine off:
*
[SV02600(ALL)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[SV02625(ALL)06/95]
2. Remove the key from the ignition after you
turn the engine off.
*
[SV02650(ALL)06/95]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

268 %
*
[SV10185(ALL)06/95]
Safety Information Relating to Automotive
Fuels
*
[SV10195(ALL)05/95]
RWARNING
Automotive fuels can cause serious injury
or death if misused or mishandled.
*
[SV10200(ALL)08/95]
Gasoline and other automotive fuels are
extremely flammable. Turn your vehicle off and
do not smoke while refueling your vehicle. Keep
sparks and other sources of ignition away from
fuels.
[SV10205(ALL)08/95]
Automotive fuels can be harmful or fatal if
swallowed.Never attempt to siphon any fuel
by mouth.
*
[SV10210(ALL)08/95]
If any fuel is swallowed, call a physician or
poison control center immediately.Do not delay
calling a physician merely because no adverse
effects are noticed at first; the toxic effects of
fuels may not become apparent for many
hours.
*
[SV10213(ALL)08/95]
If gasoline is swallowed, do not induce
vomiting. If a gasoline-methanol blend is
swallowed, induce vomiting under the direction
of a physician or poison control center.
*
[SV10215(ALL)08/95]
Gasoline and gasoline blends may contain small
amounts of carcinogens, such as benzene.
Long-term exposure to unleaded gasoline vapors
has caused cancer in laboratory animals.
*
[SV10220(ALL)08/95]
Fuels can also be harmful if absorbed through
the skin. Be careful not to splash fuel on
yourself or your clothing. If fuel is splashed on
the skin, promptly remove contaminated clothing
and wash the skin thoroughly with soap and
water.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

285 %
*
[SV23200(ALL)03/95]
Wiper Blades
*
[SV23300(ALL)03/95]
Check the windshield wiper blades at least twice
a year. Also check them whenever they seem
less effective than usual. Substances such as tree
sap and some hot wax treatments used by
commercial car washes reduce the effectiveness
of wiper blades.
*
[SV23400(ALL)09/95]
If the blades do not wipe properly, clean both
the windshield and the wiper blades. Use
undiluted windshield washer solution or a mild
detergent. Rinse thoroughly with clear water. Do
not use fuel, kerosene, paint thinner, or other
solvents to clean your wiper blades. These will
damage your blades.
*
[SV23500(ALL)03/95]
To make reaching the wiper blades easy, simply
turn the ignition to the ACC position and turn
your wipers on. Wait for them to reach a
vertical position and turn the ignition to the OFF
position. Do not move the wipers manually.
Manually moving the wipers across the
windshield may damage them.
*
[SV23600(ALL)03/01]
Wiper blade replacement
*
[SV23700(ALL)09/95]
If the wiper blades still do not work properly
after you clean them, you may need to replace
the wiper blade assembly or the blade element.
When replacing the wiper blade assembly, blade
refill, or wiper arm always use a Motorcraft part
or equivalent. To replace the blades, follow the
instructions that come with them.
[SV23705(ALL)04/95]
Your vehicle uses a 24" wiper on the driver side
and a 20" wiper on the passenger side.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

303 [SV32900( T)02/95]
If you check the power steering fluid when it is
cold, make sure that the fluid reaches the FULL
COLD range on the dipstick (3.0L Vulcan) or
MIN on the reservoir (3.0L Duratec or 3.4L
SHO). The reading will only be accurate if the
fluid temperature is approximately 50 to85ÊF (10
to 30ÊC).
% [SV32910(ALL)02/95]Fuses and Relays
[SV32915(ALL)04/95]
Fuses (conventional and high current) and relays
protect your vehicle's wiring system from
overloading. If electrical parts in your vehicle are
not working, the system may have been
overloaded and blown a fuse. Before you replace
or repair any electrical parts, check the
appropriate circuit protector. High current fuses
should only be repaired or replaced by your
Ford or Lincoln-Mercury dealer.
[SV33400(ALL)02/95]
The following charts tell you which circuit
protector protects each electrical part of your
vehicle. If a fuse blows, all the parts of your
vehicle that use the circuit will not work.
*
[SV33410(ALL)05/95]
Once you have determined which fuses to check,
follow the procedures underChecking and
replacing fuseslater in this chapter.
*
[SV33500(ALL)08/95]
RWARNING
Always remove the key from the ignition
before working on or replacing fuses.
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com

323
%*
[SV41000(ALL)03/95]
Emission Control System
[SV41100(ALL)12/95]
Your vehicle is equipped with catalytic
converters which enable your vehicle to comply
with applicable exhaust emission requirements.
*
[SV41200(ALL)06/95]
RWARNING
Exhaust leaks may result in the entry of
harmful and potentially lethal fumes into
the passenger compartment. Under
extreme conditions excessive exhaust
temperatures could damage the fuel
system, the interior floor covering, or
other vehicle components, possibly
causing a fire.
*
[SV41300(ALL)05/95]
To make sure that the catalytic converter and the
other emission control parts continue to work
properly:
*
[SV41400(ALL)01/95]
q
Use only unleaded fuel.
*
[SV41500(ALL)01/95]
q
Avoid running out of fuel.
*
[SV41600(ALL)01/95]
q
Do not turn off the ignition while your
vehicle is moving, especially at high speeds.
*
[SV41700(ALL)03/95]
q
Have the services listed in yourMaintenance
Schedule and Recordbooklet performed
according to the specified schedule.
*
[SV41710(ALL)03/95]
The Scheduled Maintenance Services listed in the
Maintenance Schedule and Recordbooklet are
required because they are considered essential to
the life and performance of your vehicle and to
its emissions system.
*
[SV41720(ALL)05/95]
Ford strongly recommends the use of genuine
Ford replacement parts. If other than Ford or
Motorcraft parts or Ford authorized
remanufactured parts are used for maintenance
replacements or for the service of components
affecting emission control, such non-Ford parts
File:15fcsvt.ex
Update:Tue Jan 23 13:58:51 1996
ProCarManuals.com