instrument panel GEELY FC 2008 User Guide

Panel/combination instrument-- panel
CodeShape
CodeShape
CodeShape
<>
=4.8
=13
2204813<>
=4.8
=19
2754819<>
=6
=20
1740620
<>
=4.8
=9.5
2754895<>
=6
=16
1400616<>
=6
=20
1400620
Panel
Preparation
1. Automobile prepares to equip with SRS airbag and safety belt pre-tension crimper.
Parking disassembling and assembling works in this chapter might influence SRS airbag. Before imple-
menting these works, it is necessary to read the notes in SRS chapter.
Change
1. Schedule for bolt, screw and screw cap
Note: when using screw driver to unclench fixing clasp or fixing clamp, it is necessary to wrap
the needled top of wrench with adhesive tape.
Hint: when disassembling or assembling panel, if necessary, use the figure and code in following
table to choose bolt, screw and screw cap.
2. Preparation
3. Disassemble leading wire of battery cathode
4. Turn front wheel to face the front
 340 
mm

Panel/combination instrument-- panel
3 Fixing clamp
4 Fixing clasp
5. Disassemble safety airbag assembly at the side of
driver [67010011] (Referring to page 261)
6. Disassemble steering wheel assembly [67010001]
(referring to page 194)
7. Disassemble Combination instrument cover
[68000077]
(a) Disassemble fixing clamp.
(b) Use screw driver to unclench three fixing clamps and four
fixing clasps, then disassemble Combination instrument.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
8. Disassemble Combination instrument assembly
[67000081]
(a) Disassemble A screw.
(b) Liking that shown in figure, unclench two fixing clamps.
(c) Disassemble the joint, then disassemble Combination in-
strument assembly.
9. Disassemble panel left ventilation hole assembly
[68010010]
Use disassembling tool for trim tape to disassemble panel left
ventilation hole assembly.
Hint: before using screw driver, it is necessary to wrap its
needled top with adhesive tape.
10. Disassemble panel right ventilation hole assembly
[68010011]
11. Disassemble front ashtray
12. Disassemble shift organization trim board assem-
bly [68000076]
(a) Use screw driver to unclench six fixing clamps.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
(b) Disassemble the joint, then disassemble shift organization
trimmain board.
 341 
4 Fixing clasp
6 Fixing clamp

Panel/combination instrument-- panel
<F> 8 Fixing
clamp
8 Fixing
clamp
<>
Fixing clamp
2 Fixing clasp
4 Fixing clamp
4 Fixing clasp
13. Disassemble air conditioner control panel assem-
bly [67000148]
(a) Use screw driver to unclench four fixing clamps and four
fixing clasps, then disassemble air conditioner control panel
assembly.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
(b) Disassemble the joint.
14. Disassemble CD machine assembly [67000126]
(a) Disassemble two E self tapping screws and two F bolts.
(b) Use screw driver to unclench eight fixing clamps, then dis-
assemble DVD assembly and panel central ventilation hole
assembly.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
(c) Disconnect panel central ventilation hole assembly.
15. Disassmble lower panel right storage box assem-
bly [68100008]
(a) Disassemble A screw and gas spring on storage box.
(b) Bend upper part of storage box to release gas spring.
(c) Pull put storage box upwards.
16. Disassemble right front pillar inner trim board as-
sembly [68010017]
(a) Unclench two fixing clamps.
(b) Pull out right front pole inner trim board upwards.
17. Disassemble left front pole inner trim board assem-
bly [68010014]
18. Disassemble the joint of safety airbag assembly at
the side of passenger (referring to page 263)
 342 

Panel/combination instrument-- panel
6 Fixing clamp
5 Fixing clasp
19. Disassemble upper panel assembly [68010004]
(a) Disassemble D bolt and two A screws.
(b) Use disassembling tool for trim tape to unclench six fixing clamps.
(c) Disassemble upper panel assembly.
20. Disassemble upper/lower trim board of steering column [64000128/64000129]
21. Disassemble left combination switch assembly [67000078] (referring to page 298)
22. Disassemble right combination switch assembly [64000079] (referring to page 302)
23. Disassemble gas spring
Unclench fixing clamp, then disassemble gas spring.
 343  24. Disassemble evaporator ventilation pipe assembly
[67000149]
Disassemble four fixing clamps and evaporator ventilation pipe
assembly.
gas
spring

Panel/combination instrument-- panel
L
4 Fixing
clasp
3 Fixing
clasp
Fixing
clamp
25. Disassemble parking brake hole cover.
Use screw driver to unclench four fixing clamps, then disas-
semble parking brake hole cover.
Hint: before using screw driver, it is necessary to wrap its
needled top with adhesive tape.
26. Disassemble auxiliary panel assembly [68010002]
(a) Disassemble two L bolts, two C bolts and auxiliary panel
assembly.
27. Disassemble right front door pedal trim board
[68010021]
Use screw driver to unclench three fixing clamps, then disas-
semble right front door pedal trim board.
Hint: before using screw driver, it is necessary to wrap its
needled top with adhesive tape.
28. Disassemble left front door pedal trim board
[68010020]
29. Disassemble lower inner trim board of right de-
fender [68010016]
(a) Disassemble plastic nuts of lower inner trim board of right
defender.
(b) Unclench fixing clamp, then disassemble lower inner trim
board of right defender liking that shown in figure.
30. Disassemble lower inner trim board of left defender
[68010015]
31. Disassemble connecting board at the middle of
panel [68010006]
(a) Use screw driver to unclench four fixing clamps, then open
the connecting board at the middle of panel.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
(b) Disassemble connecting board at the middle of panel.
 344 

Panel/combination instrument--panel
32. Disassemble lower panel assembly [68010005]
(a) Disassemble the joint of indoor temperature sensor.
(b) Disassemble machine cover locking pull cable with handle assembly.
(c) Disassemble six D bolts.
(d) Disassemble six fixing clamps and panel lower board.
33. Disassemble left storage box of lower panel [68010007]
34. Assemble upper panel assembly [68010004]
Assemble upper panel assembly with D bolt and two A screws.
D bolt: 18 N⋅m
35. Assemble CD machine assembly [67000126]
(a) Assemble pedal central ventilation hole assembly on CD machine assembly.
<D><D><D>
<D>
<D>
<D>
 345 

Panel/combination instrument--panel
(b) Assemble CD machine assembly and panel central ventila-
tion hole assembly.
36. Assemble helix cable assembly (referring to page
261)
37. Assemble steering wheel assembly [67010001]
(referring to page 194)
38. Check the central position of steering wheel.
39. Check the safety airbag assembly at the side of
driver [67010011] (referring to page 249)
40. Assemble the safety airbag assembly at the side of
driver [67010011]
41. Check the warning light of SRS airbag
Fixing
clamp
4 Fixing
clamp
 346 

Combination instrument assembly
Disassembly and assembly
1. Disassemble Combination instrument cover [68000077]
(a) Disassemble fixing clamp.
(b) Use screw driver to unclench three fixing clamps and four fixing clasps, then disassemble combination
penal cover.
 347 
Panel/combination instrument--Combination instrument assembly
2. Disassemble Combination instrument assembly
[68000081]
(a) Disassemble the screw.
(b) Liking that shown in figure, unclench two fixing clamps.
(c) Disassemble the joint, then disassemble Combination
instrument.

Anti-stealing and door lock--Electric door lock control system
3. Check panel junction box assembly.
(a) Check 25A DOOR fuse.
(b) Check conformity relay.
(1) Disassemble F, G, H and I joint on instrument junction
box.
(2) Check the voltage and conduction of every terminal of
joint. (d) Check security function:
(1) When closing all doors, open the driver window to operate door control switch out of automobile.
(2) Take down the key, open driver door, then close the door and lock (not use key). In this situation
above, check that door could not open locker even if door control switch (handle operation) is
pressed to locker opening side out of automobile.
(3) Take down the key, close and use the key to lock driver door. In this situation above, check that
door could not open locker even if door control switch (handle operation) is pressed to locker
opening side out of automobile.
(4) Take down the key, close and use remote control key to lock driver door. In this situation above,
check that door could not open locker even if door control switch (handle operation) is pressed to
locker closing side out of automobile (only applicable for the automobile equipping with remote
control door locker control system).
Hint:
zIn following situation, check whether security has been canceled.
zIgnition switch is turned to ON.
zUse key operation to open the driver door locker.
zAfter door locker is pressed to opening side by hand, door control switch (handle
operation) is pressed to locker opening side.
zUse remote control locker control to open the door (only applicable for the automobile
equipping with remote control door locker control system).
2. Electric window main switch assembly
Operate door control switch by hand to check its conduction.
 356 
Position of switch Terminal connected by avometerRegulated situation
LOCK 5-1 or 5-3Conduction
UNLOCK8-1 or 8-3↑