oil GEELY FC 2008 Manual Online

(e) If there is any foam or emulsification phenomenon, it is necessary to exhaust air in power steering
system.
(f) Keep the engine at idling speed, and measure the oil
level of oil storage tank.
(g) Engine extinguishes.
(h) After waiting for several minutes, measure the oil level
of oil storage tank again.
Maximal increased height of oil level: 5mm
If finding any problem, it is necessary to exhaust
the air in power steering system.
(i) Check the oil level.
4. Check steering oil pressure.
(a) Disassemble oil pressure supply pipe from power steering gear. (referring to page 205)
(b) Connect special tool liking that shown in figure.
Note: when checking, the valve of special tool should be opened.
(c) Exhaust the air in power steering system.
(d) Start the engine, and keep it at idling speed.
(e) Turn steering wheel from left bottom to right bottom for several times to make oil temperature
Power steering--Poser steering system
increase.
Oil temperature: 80°C
(f) Keep the engine at idling speed, and close the valve of
special tool, then observe the reading of special tool.
Minimal oil pressure: 6400kPa
Note:
yThe closing time of oil pressure meter valve could not
Accessory
Power steering
gear
InOut
Accessory Oil pressure supply pipe
Power
steering
gearClose
Pump Oil tank
Special tool
¡Ü¡Ü
¡Ü¡Ü¡Ü5mm
Special tool
 201 

Power steering--Power steering system
exceed 10 seconds.
yDo not make oil temperature become too high.
(g) When engine is running at idling speed, open the valve
completely.
(h) Measure the 1.000 rpm and 3.000 rpm oil pressure of
engine.
Oil pressure difference: 490 kPa or less
Note: do not turn the steering wheel.
(i) When engine is running at idling speed, open the valve
completely, and turn the steering wheel to bottom.
Minimal oil pressure: 6,400kPa
Note:
yDo not keep the wheel locate at bottom for over 10
seconds.
yDo not make oil temperature become too high.
(j) Disassemble the special tool.
(k) Connect oil pressure supply pipe with power steering gear
(referring to page 205)
(l) Exhaust the air in power steering system.
5. Check the steering force
(a) Put the steering wheel at central position.
(b) Disassemble safety airbag assembly at the side of driver.
(c) Start engine, and make it run at idling speed.
(d) Measure the steering force of two directions.
Steering force (reference): 5.5 N
x xx x
xm
Hint:before diagnosing, it is necessary to consider
the tyre type, tyre pressure and contacting sur-
face at first.
(e) Tighten fixed screw cap of steering wheel.
Torque: 50 ± 5 N
x xx x
xm
(f) Assemble the safety airbag assembly at the side of driver.
Power
steer-
ing
gearOpen
Pump Oil tank
Open
Pump Oil tank
Power
steering
gear
Turn the steering wheel
to the bottom position
Special tool
Special tool
 202 

Power steering--Power steering oil pump assembly
Power steering oil pump assembly
Overhaul
1. Disassemble front wheel
2. Disassemble right bottom defender board [68000004]
3. Disassemble driving belt.
4. Disassemble oil storage tank to the No. 1 oil pipe
of power steering pump
Disassemble fixed clamp, and take down the oil storage tank
to the No. 1 oil pipe of power steering pump.
5. Disassemble in-out oil pipe assembly of power
steering gear [64000131]
(a) Use special tool to disassemble in-out oil pipe assembly.
(b) Disassemble the bolts and disconnect the fixed clamp of
in-out oil pipe.
6. Disassemble rear bracket of power steering pump
Disassemble the bolt and rear bracket of power steering pump.
7. Disassemble power steering oil pump assembly
[64000132]
(a) Disconnect the joint of oil pressure switch.
(b) Disassemble two bolts, two screw caps, then take down
the power steering oil pump assembly.
8. Assembly power steering oil pump assembly
(a) Assemble power steering oil pump assembly with two
bolts and two screw caps.
Torque: 37 N
x xx x
xm
(b) Connect the joint of oil pressure switch.
Note: the joint could not contact any oil.
9. Assemble the rear bracket of power steering oil pump assembly
Assemble rear bracket of power steering oil pump assembly with bolts.
Torque: 37 N
x xx x
xm
Hint:Insure the stop lever of bracket has contacted the body of power steering pump, then
tighten the bolt.
 203 
Special tool

10. Connect the in-out oil pipe assembly of power
steering gear [64000131]
(a) Assemble fixed clamp of in-out oil pipe with bolt.
Torque: 7.8 N
xm
(b) Connect in-out oil pipe with special tool.
Torque: 41 Nz
xm
Hint:
zUse torque wrench whose lever length is 345 mm.
zSpecial tool should be parallel with torque wrench,
only this could make practical torque value.
11. Connect the N0. 1 oil pipe of oil storage tank to power steering oil pump assembly.
Connect oil pipe with fixed clamp.
12. Assemble driving belt.
13. Assemble front wheel.
Torque: 103 ± 10 Nx xx x
xm
14. Add power steering oil.
15. Exhaust the air in power steering system.
16. Check whether there is any oil leakage.
17. Assemble right bottom defender board of engine [68000004].
Power steering--Power steering oil pump assembly
Special
tool
¸Ü¸Ü
¸Ü¸Ü¸Ü¸Ë¸Ë
¸Ë¸Ë¸Ë³¤³¤
³¤³¤³¤¶È¶È
¶È¶È¶È
 204 

Power steering gear assembly
Overhaul
1. Make front wheel face the front
2. Disassemble safety airbag assembly at the side of driver
(equipping with SRS) [6701011]
3. Disassemble steering wheel assembly [67010001].
4. Disassemble dust-proof cover in steering column
[64000123].
Disassemble two screw caps, then take down the dust-proof
cover.
5. Disassemble steering sliding shaft assemble
(a) Make mark on sliding yoke and steering middle shaft.
(b) Loosen A bolt and disassemble B bolt, then disassemble
sliding shaft.
6. Disassemble front wheel
7. Disassemble right bottom defender board [68000004].
8. Disassemble left bottom defender board [68000003].
9. Disconnect left end terminal of transversal lever
(a) Disassemble cotter pin and screw cap.
(b) Use special tool to disassemble the left end terminal of
transversal lever from steering knuckle.
Hint: disassemble the other with same method.
10. Disassemble right end terminal of transversal lever.
11. Disassemble in-out oil pipe assembly of power
steering gear [64000131].
(a) Use special tool to disassemble in-out oil pipe assembly
of power steering gear.
Power steering--Power steering gear assembly
Align the mark
Special tool
Special tool
 205 

Power steering--Power steering gear assembly
(b) Disassemble the screw and disconnect the fixed clamp of
in-out oil pipe assembly of power steering gear.
12. Disassemble linking lever assembly of front stabi-
lizer bar [64000097].
(a) Use socket head wrench (5mm) to fix bolt, then disas-
semble screw cap.
(b) Disassemble the left linking lever of front stabilizer liking
lever assembly.
Hint: disassemble the other with same method.
13. Disassemble the coupling bolt and nut of left/right
lower control arm ball head and control arm.
Disassemble one bolt and two nuts, and disassemble control
arm from left steering knuckle.
Hint: disassemble the other with same method.
14. Disassemble engine cover assembly
15. Support engine assembly.
16. Disassemble auxiliary automobile bracket assem-
bly [64000087]
(a) Disassemble two bolts, then disassemble side rail from
right front engine suspension.
(b) Disassemble two bolts, then disassemble carling from au-
tomobile body.
(c) Disassemble the bolt and three nuts, then disassemble
engine rear suspension from auxiliary automobile bracket.
(d) Use gearbox jack to support auxiliary automobile bracket.
(e) Disassemble four bolts and auxiliary automobile bracket
assembly with steering gear.
17. Disassemble exterior dust-proof cover of steering
column.
 206 

Power steering--Power steering gear assembly
29. Assemble steering No.2 dust-proof cover.
(a) Insure steering gear hole is not plugged by lubricating
grease.
Hint: if hole is plugged, the pressure in dust-proof
cover when steering wheel turns after combin-
ing will change.
(b) Assemble dust-proof cover, fixed clamp and new iron wire.
Note: do no t hurt or bend dust-proof cover.
(c) After coiling dust-proof cover with iron wire for two circles,
turn it for several circles to fix it.
(d) Liking that shown in figure, bend iron wire to rotating di-
rection to prevent it from hurting dust-proof cover.
Hint: assemble the other side with same method.
30. Assemble No.1 dust-proof cover of steering gear.
31. Assemble left ball head of transversal lever .
(a) Screw locking cap and transversal lever ball head in gear
terminal lever until aligning the mark.
(b) After adjusting front wiring harness, tighten the screw cap
(referring to page 80).
Torque: 74 ± 5 N
xm
Hint: assemble the other side with same method.
32. Assemble right ball head of transversal lever .
33. Assemble power steering gear assembly [64000133].
(a) Assemble power steering gear assembly on beam with
four bolts.
Torque: 58 N
xm
 209 
Align the mark

Power steering--Power steering gear assembly
37. Connect the bolts and nuts of left/right control arm
and control arm ball head.
Torque: 142 ± 10 Nx xx x
xm
Hint: connect the other side with same method.
Connect left lower control arm to steering knuckle with
bolt and two nuts.
38. Connect linking lever assembly of left/right front
stabilizer bar [64000097].
Use socket head wrench (5mm) to fix bolt, then connect sta-
bilizer linking lever with screw cap.
Torque: 74 ± 5 N
x xx x
xm
Hint: connect the other side with same method.
39. Connect the in-out oil pipe assembly of power steer-
ing gear [64000131].
(a) Connect the in-out oil pipe fixed clamp of power steering
gear with bolt.
Torque: 7.8 N
x xx x
xm
(b) Use special tool to connect the in-out oil pipe assembly of
power steering gear.
Torque: 41 N
x xx x
xm
Hint:
zUse the torque wrench whose lever length is
345mm.
zSpecial tool should be parallel with torque wrench,
only this could make practical torque value.
Hint: connect the other side with same method.
40. Connect the ball head at the left side of transversal
lever.
(a) Connect the ball head at the left side of transversal lever
with screw cap.
Torque: 49 ± 5 N
x xx x
xm
(b) Assemble new cotter pin.
Note: if cotter pin hole could not be aligned , tighten
the screw cap for 60 again.
Hint: connect the other side with same method.
 211 
Length of lever

Power steering--Power steering gear assembly
41. Connect the ball head at the right side of transver
sal lever .
42. Assemble right bottom defending board of engine
[68000004].
43. Assemble left bottom defending board of engine
[68000003].
44. Assemble front wheel
Torque: 103 ± 10 Nx xx x
xm
45. Connect steering slide shaft assembly.
(a) Align the mark between steering middle shaft and sliding
shaft.
(b) Assemble B bolt.
Torque: 35 ± 3 N
x xx x
xm
(c) Tighten the A bolt.
Torque: 35 ± 3 Nx xx x
xm
46. Assemble inner dustproof cover of steering column [64000123].
Assemble inner dustproof cover of steering column with two screw caps.
47. Make front wheel face the front
Hint: lift up front wheel shaft.
48. Assemble helix cable assembly (equipping with SRS).
49. Assemble steering wheel assembly [67010001].
(a) Align the mark between steering wheel and main shaft of steering column.
(b) Lock the fixed screw cap of steering wheel temporarily.
50. Add power steering oil (referring to page 200).
51. Exhaust the air in power steering system (referring to page 200).
52. Check the central point of steering wheel.
(a) Check the central point of steering wheel.
(b) Lock the fixed screw cap of steering wheel.
Torque: 50 ± N
x xx x
xm
53. Assemble safety airbag assembly at the side of driver (equipping with SRS) [67010011].
54. Check whether there is oil leakage.
55. Check the engine cover assembly.
56. Adjust the engine cover assembly.
57. Check and adjust the front wheel alignment (referring to page 87).
 212 

Air conditioner--Air conditioning system
Air conditioner
Air conditioning system
Note
1. Do not dispose Refrigerant in sealed space or near
flame.
2. Wear glasses to protect your eyes.
3. Do not let liquid Refrigerant contact with your eyes
or skin.
If liquid Refrigerant contacts with your eyes or skin:
(a) Wash the contacted part with much water.
Warning: do not knead your eyes or skin.
(b) Spread clean Vaseline on your skin.
(c) Go to doctor or hospital for special cure.
4. Forbid heating it or making it expose the flame.
5. Forbid dropping the Refrigerant tank or shake it
intensively.
6. Do not operate compressor when Refrigerant is lack.
If the Refrigerant in cooling system is lack, it will incur com-
pressor burned out for lacking lubrication. So it is necessary
to avoid.
7. Do not open the high pressure valve of filling instru-
ment package when compressor is working.
If opening the valve at this time, Refrigerant will flow back into
refrigerant tank to incur the tank will break. So only the low
pressure valve could be opened or closed.
8. Do not fill Refrigerant too much.
Too much refrigerant will make many problems such as lack
cooling degree, oil consumption, too hot engine and so on.
Inspection on automobile
1. Check the No.1 pressure switch.
(a) Control for electromagnetic clutch:
Check the function of pressure switch.
(1) Assembly filling instrument package.
(2) Connect the anode lead of OUM meter to No. 4 termi-
nal and connect cathode lead to No. 1 terminal.
(3) Liking that shown in figure. When refrigerant pressure
is changed, check the conduction between terminals.
wrong correct
Low-pressure
sideHigh-pressure
side
Not
conductionCon-
duction
Not
conduction
 213