door lock GEELY FC 2008 Workshop Manual

Replacement.................................................
308
Left front door loudhailer....................................
309
Change..........................................................
309
Left front small loudhailer..................................
310
Change..........................................................
310
Rear loudhailer..................................................
311
Change..........................................................
311
Outdoor antenna...............................................
312
Change..........................................................
312
Circuitry
Power supply......................................................
313
Components..................................................
313
Horn system
Horn system.......................................................
316
Position..........................................................
316
Inspect...........................................................
316
Windshield/window glass/wing mirror
Electric window control system..........................
317
Position drawing............................................
317
Inspect the car...............................................
317
Malfunction phenomena table.......................
319
Inspect...........................................................
319
Front windscreen................................................
321
Change..........................................................
321
Rear ventilation window.....................................
324
Change..........................................................
324
Fog defrost system............................................
327
Position drawing...........................................
327
Malfunction phenomena table......................
327
Inspect...........................................................
328
Electric rearview mirror control system(option).
329
Inspect the vehicle.........................................
329
Position drawing...........................................
331
Trouble table.................................................
331
INSPECT.......................................................
332Panel / combination panel
combination panel
..............................................
334
Trouble table..................................................
334
Vehicle inspection..........................................
335
Inspection......................................................
339
Panel..................................................................
340
Preparation....................................................
340
Change..........................................................
340
Combination instrument assembly.....................
347
Disassembly and assembly...........................
347
Chair
Front chair..........................................................
348
Subassembly.................................................
348
Overhaul........................................................
349
Rear chair (separating type)...............................
352
Overhaul........................................................
352
Rear chair (fixing type).......................................
354
Overhaul........................................................
354
Anti-stealing and door lock
Electric door lock control system........................
355
Position of parts.............................................
355
Inspection on automobile...............................
355
Malfunction phenomenon table.....................
358
Inspection......................................................
359
Electronic anti-stealing system...........................
361
Electric sunroof
Sunroof.................................................................
362
Overhaul........................................................
362
Specification for sunroof function......................
364
Inspection for sunroof function......................
364
Inspection for sunroof switch........................
365
Position of parts............................................
365
Malfunction phenomenon table....................
365

Engine cover/automobile door
Engine cover......................................................
366
Adjustment.....................................................
366
Front automobile door........................................
367
Subassembly.................................................
367
Overhaul........................................................
369
Adjustment.....................................................
372
Rear automobile door.......................................
373
Overhaul........................................................
373
Adjustment....................................................
375
Trunk cover.........................................................
377
Adjustment....................................................
377
Torsion spring of trunk cover.............................
378
Change..........................................................
378
Exterior/inner trim board
Front bumper....................................................
379
Subassembly................................................
379
Change..........................................................
380
Rear bumper......................................................
381
Subassembly................................................
381
Change..........................................................
382
Name plate........................................................
383
Change..........................................................
383
Exterior seal tape of left front door glass (LH)...
384
Change..........................................................
384
Exterior seal tape of left rear door glass...........
385
Change..........................................................
385
Light fender........................................................
386
Change..........................................................
386
Top left trim tape.................................................
387
Replacement.................................................
387
Left lower fender of automobile body (LH)........
388
Subassembly................................................
388
Change..........................................................
389
Inner trim board of top........................................
390
Change..........................................................
390Automobile control system
Ignition switch and anti-versa lock key warning switch.394
Malfunction phenomenon table.....................
394
Inspection......................................................
394
Electrical schematic diagram..............................
395

Engine mechanism - Engine assemblyEngine assemblyReplacement1. Take measures to prevent gasoline leaking.
2. Remove engine right bottom shield.
3. Remove engine left bottom shield.
4. Discharge coolant.
5. Remove front wheels.
6. Remove engine plastic hood components.
7. Remove battery.
8. Remove air filter assembly.
9. Remove air filter hose.
10. Remove battery tray.
11. Disassemble fuel hose assembly.
12. Remove throttle cable assembly.
13. Disassemble radiator hose inlet end.
14. Disassemble radiator hose outlet end.
15. Disassemble cold air pipe inlet hose.
16. Disassemble cold air pipe outlet hose.
17. Remove transmission control pull cable assembly.
18. Disassemble warm air water inlet hose [4G18-1300102].
19. Disassemble warm air water outlet hose [4G18-1300108].
20. Disassemble the hoses of all joints to connect vehicle body end.
21. Uncouple engine wire harness.(a) Remove glove compartment door.
(b) Remove engine wire harness from engine ECU and junction block.
(c) Pull out engine wire harness.
(b) Remove engine wire harness from junction block of engine room.
(e) Remove vehicle body earth wire. 36

Supplemental restraint system--Repair
Repair
a. In using process, if happening any malfunction of power supply, it shows the voltage of power supply
is less than 9V or higher than 18V, or the battery is damaged, at this time, it only needs to charge or
change the battery.
b. Use special malfunction diagnostic tool to test.
Malfunction codes approved by safety airbag controller (KD4.1)
Number Malfunction specification Remove
1Ignition circuit 1 (safety airbag at the side of driver), the resistance is too high or open circuit.OK
2
Ignition circuit 1 (safety airbag at the side of driver), the resistance is too low or short circuit.OK
3
Ignition circuit 1 (safety airbag at the side of driver), connects with the groundingOK
4
Ignition circuit 1 (safety airbag at the side of driver), connects with power supplyOK
5
Ignition circuit 2 (safety airbag at the side of passenger), the resistance is too high or open circuit.OK
6
Ignition circuit 2 (safety airbag at the side of passenger), the resistance is too low or short circuit.OK
7
Ignition circuit 2 (safety airbag at the side of passenger), connects with the groundingOK
8
Ignition circuit 2 (safety airbag at the side of passenger), connects with power supply.OK
9
Ignition circuit 3 (pre-tension safety belt at the side of driver), the resistance is too high or open circuit.OK
10
Ignition circuit 3 (pre-tension safety belt at the side of driver), the resistance is too low or short circuit.OK
11
Ignition circuit 3 (pre-tension safety belt at the side of driver), connects with the groundingOK
12
Ignition circuit 3 (pre-tension safety belt at the side of driver), connects with the power supplyOK
13
Ignition circuit 4 (pre-tension safety belt at the side of passenger), the resistance is too high or open circuit.OK
14 Ignition circuit 4 (pre-tension safety belt at the side of passenger), the resistance is too low or short circuit. OK
15
Ignition circuit 4 (pre-tension safety belt at the side of passenger), connects with the groundingOK
16
Ignition circuit 4 (pre-tension safety belt at the side of passenger), connects with power supplyOK
17
Voltage of power supply is too highOK
18
Voltage of power supply is too lowOK
19
Malfunction of indicating light connects with power supply or bulb is short circuit.OK
20 Malfunction of indicating light connects with the grounding or filament is open circuit. OK
21
Lack/wrong calculation rule parametersNo (change safety airbag
controller (KD4.1))
22Front impact has been recordedNo (change safety airbag
controller (KD4.1))
23
Communication malfunctionOK
24
Inner malfunctionNo (change safety airbag
controller (KD4.1))
25
Impact output (oil pump) pin connects with the groundingOK
26
Impact output (oil pump) pin short connects with power supplyOK
27
Impact output (central control door lock) pin connects with the groundingOK
28
Impact output (central control door lock) pin connects with power supplyOK
29
Pre-tension safety belt ignites independentlyOK, but most is five times
30
Pre-tension safety belt ignites six times independentlyNo (change safety airbag
controller (KD4.1))
 247 

d. Loosen the connectors of all safety airbag system units,
e. Check whether the connector between electronic control unit of safety airbag system and the
circuit between connector of safety belt pre-tension have following situations:
zEarth
zShort connection with power supply
zOpen circuit
f. Are the wiring harnesses above normal?
Normal: malfunction diagnosis ends
Abnormal: change related wiring harness.
8. Malfunction of impact output
Malfunction of safety airbag assembly at the side of passenger (resistance is too big
or too small, short circuit, grounding and so on)
Resting conditionWarning
zIf the treatment is wrong, safety airbag assembly and pre-tension safety belt might be
triggered to unfold and tighten to make heavy human hurt, so, before the treatment, it
is necessary to read repairing warnings carefully.
Refer to repairing warning of safety airbag system.
Possible reason
zConnector between impact output circuit and electronic control unit of safety airbag sys-
tem has malfunction.
zConnector between safety airbag system unit and grounding position has malfunction.
zThe circuit between impact output circuit and electronic control unit of safety airbag
system happens open circuit or short circuit.
zCircuit between safety airbag system unit and grounding position happens open circuit
or short circuit.
zSafety airbag system unit has malfunction.
(1) Check whether this airbag controller has impact output function
a. Set ignition switch at LOCK position
b. Loosen the cathode cable of battery and keep this state for one minute at least
(2) Check whether the connection of impact output connector is good,
(3) Check whether the impact output connecting wire is earth or is short connecting with other wires,
(4) Check whether impact output connecting wire is open circuit,
(5) Check whether the central control door lock control system or electric injection control system of
engine has been changed,
Note: If repairing it by the steps above and requirements, indicating light or diagnostic tool
could display the mistakes before repairing all the time, please do not change it by
yourself, you should contact with the manufacturer as soon as possible avoid wrong
explosion or no explosion when using airbag.
Supplemental restraint system--Remove malfunction
 259 

Safety belt--Front safety belt
(1) Connect special tool with battery,
Connect the red clamp of special tool with the anode of
battery (+), and black clamp with the cathode of battery
(-).
Hint: Do not connect the yellow joint with safety
belt pre-tension crimper.
(2) Confirm the function of special tool.
Press working switch of special tool, then the LED on
switch should illuminate.
Warning: if working switch is not pressed, LED
illuminates, then special tool might have
malfunction, at the this time, do not use the
special tool.
(b) Disassemble the joint of safety belt pre-tension crimper.
(1) Disassemble panel trim board of front door,
(2) Disassemble panel trim board of rear door.
(3) Disassemble lower fixed bolts and trim cover of safety
belt.
(4) Disassemble lower inner trim board of middle column.
(5) Liking that shown in figure, disassemble the joint of safety
belt pre-tension crimper.
(c) Assemble special tool
(1) Assemble lower fixed bolts and trim cover of safety belt.
(2) Connect two special tools with lower fixed bolts and trim
cover of safety belt..
Note: to avoid damaging the joint and wiring har-
ness of special tool, do not lock the twice lock
of dual-lock organization.
(3) Move the special tool apart from the front end of auto-
mobile for 10m at least.
(4) Close all doors and windows.
Note: do not damage wiring harness of special tool.
(5) Connect the read clamp of special tool with the anode
of battery (+), and black clamp with the cathode of bat-
tery (-).
Special
toolBattery
Special
tool
Special
toolSpecial
tool
Over 10m
 271 

Safety belt--Front safety belt
Subassembly
(e) Treatment for safety belt pre-tension crimper.
(1) Disassemble the tyre and special tool.
(2) Put safety belt pre-tension crimper in plastic bag, then
bind the bag for treatment with other parts.
N.
m : Regulated torque
Trim board of pedal of
front doorFront safety belt
locker assembly Trim cover of safety belt
lower fixed bolt Trim board of pedal
of rear door Front safety belt
crimper assembly Lower inner defending
board of middle columnTrim cover of safety belt
upper fixed bolt41
Q184C1020
41
Q184C1020
41
Q184C1020
41
Q184C1020
 273 

Safety belt--Front safety belt
Change
Hint:
zWhen assembling, please work by the sequence that is reverse with disassembling sequence,
if necessary, assembling instruction could be got.
zChanging procedure for left side and right side is same.
zRefer to subassembly drawing of front safety belt on page 273.
1. Disassemble cathode wire of battery.
2. Disassemble left front safety belt locker assembly [68010040].
(a) Disassemble driver seat assembly (referring to page 349).
(b) Disassemble safety belt locker assembly in side of driver seat gasket (referring to page 349).
(c) Only driver side: disassemble fixed clamp from gasket bracket of driver seat.
(d) Disassemble the bolts and safety belt locker assembly in side of front seat.
3. Disassemble trim board of pedal of left front door [68010020].
4. Disassemble trim board of pedal of left rear door [68010022].
 274  5. Disassemble sealed part of doorframe of left front
door [68010055].
6. Disassemble sealed part of doorframe of left rear
door [68010059].
7. Disassemble lower inner trim board of left middle
column [68010018].
8. Disassemble left front safety belt crimper assembly
[68010044].
(a) Use right-angled screwdriver to disassemble trim cover of
upper fixed bolt of safety belt.
Hint:use adhesive tape to twist its top end before using.
(b) Disassemble the bolts and crimper assembly.
(c) Use right-angled screwdriver to disassemble trim cover of
upper fixed bolt of safety belt.
Hint:use adhesive tape to twist its top end before using.
(d) Disassemble the bolts and lower fixed bolts of floor safety belt.
(e) Disconnect the joint of crimper liking that shown in figure.
Note:when disassembling the safety belt, it is necessary to turn the ignition switch to LOCK
position, and disconnect the cathode of battery for 90 seconds, then it could start to work.
(f) Disassemble the bolts and crimper.
9. Assemble left front safety belt crimper assembly.
(a) Check the inclining angle when ELR starts to lock.
(1) Confirm whether safety belt could be pulled out if the angle exceeds 45°.
Note: do not disassemble the crimper.
(b) Use the bolts to assemble crimper.
Torque: 41 N·m
(c) Use two bolts to assemble fixed seat of side shoulder belt
and safety belt.
Torque: 41 N·m
(d) Check the lock of ELR.
(e) After safety belt is assembled on automobile, check whether
the safety belt could be locked when it is pulled out quickly.
10. Assemble left front inside safety belt clamp.
Torque: 41 N·m

Light--Light System
(a) Turn the ignition switch to OFF and open all doors, then lock driver cap side door.
(b) Unlock the drive’s side door and open any door, then inspect whether room light lights. Close the door
and inspect whether room light lights off in 15 seconds.
(c) Turn ignition switch to ON, then open any door to inspect whether room light lights off immediately.
(d) Turn ignition switch to OFF.
(e) Open or close any door to light room light. Turn ignition switch to ON before room light turns off(about
15seconds) to inspect whether room light turns off immediately.
(f) Turn ignition switch to OFF.
(g) Open or close any door to light room light. Lock driver cap side door before room light turns off(about
15seconds) to inspect whether room light turns off immediately.
Inspect
1. Front combination headlight dimmer switch
assembly
(a) Inspect the conduction of light control switch
(1) Inspect switch on every positions, the conduction among
terminals as following table.
Switch positionsAvometer terminalsregular situations
OFF - not conduction
Position light12-6conduction
Lamp12-6conduction
Lamp7-10conduction
(b) Inspect conduction of front assembled dimmer switch
(1) Inspect switch on every parts, the conduction among terminals as following table.
Switch positionsAvometer terminalsregular situations
Flasher 11-10conduction
Low beam light9-10conduction
Distant light7-10conduction
(c) Inspect the conduction of turning light switch
(1) Inspect switch on every positions, the conduction among terminals as following table.
Switch positionsAvometer terminalsregular situations
Turn right 4-5conduction
neutral -not conduction
turn left 4-3conduction
 283 

Light--Light System
(a) Inspect the conduction of B pillar control switch assembly
(1) Inspect the conduction between terminal 1 and bodywork earth, when switch works.
Standard:
ON (when press the switch): conduction
OFF (when un-press the switch): not conduction
7. Inspect the C door pillar control switch assembly [67000076]
(a) Inspect the conduction of C pillar control switch assembly
(1) Inspect the conduction between terminal 1 and bodywork earth,when switch works.
Standard:
ON (when press the switch): conduction
OFF (when un-press the switch): not conduction
8. Trunk light switch assemble [67000073]
(a) Inspect the conduction of Trunk light switch
Standard:
ON (when press the switch): conduction
OFF (when un-press the switch): not conduction
9. Front fog light relay [67000071]
(a) Inspect the conduction of front fog light relay
(1) Inspect the conduction among terminals
Standards:
Avometer terminalsregular situations
1-2 conduction
3-5 not conduction
10. Inspect rear fog light switch of instrument block
left switch units [67010003].
(a) Inspect battery’s positive wire connects to terminal 1,nega-
tive connects to terminals 7.
(b) Connect a 3.4W test bulb from battery’s positive wire to
terminal 3.
(c) Inspect lighting switch, indicator light of assembled instru-
ments and test bulb should light. If it does not accord with
regularizations, replace the switch.
11. Inspect door light assembly [67000107]
Inspect the conduction among terminals.
If the conduction does not accord with regularizations, replace
the switch.(2) Supply battery voltage(10-14V) to terminal1 and terminal2, then inspect the conduction between
terminal 3 and terminal 5.
Standard: conduction
1
 285