trunk GENESIS G80 2023 Owner's Guide

6-8
Driving Your Vehicle
Remote Start
„Type A
ORG3EV061008
„Type B
ORG3EV061009
You can start the vehicle using the
Remote Start button of the smart key.
To start the vehicle remotely:
1. Press the door lock button within 32
feet (10 m) from the vehicle.
2. Press the remote start (
) button for
over 2 seconds within 4 seconds after
locking the doors.3. To turn off the remote start function,
press the remote start (
) button
once.

[The remote start (
) button may not
operate if the smart key is not within
32 feet (10 m).

[The vehicle will not remotely start if
the hood or trunk is opened.

[The vehicle must be in P (Park) for the
remote start function to start.

[The vehicle turns off if you get in the
vehicle without a registered smart key.

[The vehicle turns off if you do not get
in the vehicle within 10 minutes after
remotely starting the vehicle.

6-19
06
Automatic engagement of EPB
After the vehicle is stopped by the
One Pedal Driving function, EPB is
automatically engaged when any of
these conditions occur:

[The driver’s seatbelt is unfastened and
the driver’s door is open.

[The shift gear is changed N (Neutral)

[The hood is open.

[The trunk is open.

[5 minutes have passed since the
vehicle has stopped.

[The system operation is limited due to
other reasons.
WARNING

[Stopping the vehicle may not be
possible according to the vehicle and
road conditions. Pay attention to the
road condition ahead and apply the
brake if necessary.

[Please refrain to use the one
pedal driving function when road
conditions are poor, such as when
wet, icy or covered with snow.
CAUTION
When the vehicle is stopped or parked by
One Pedal Driving on steep hills, be sure
to also press the brake pedal.
i-Pedal
i-Pedal is controlled by the accelerator
pedal. i-Pedal provides vehicle speed
control (acceleration/deceleration,
stopping) without manually controlling
the paddle shifter.To operate:

[Pull the left side paddle shifter at level
3 regenerative braking system.

[During the activation of i-Pedal, the
vehicle is stopped when the vehicle
speed is less than 1 mph (3 km/h) even
if the brake pedal is not pressed.

[When you press the accelerator pedal
at the same time during one-pedal
driving by pulling the left paddle shift
lever, the vehicle cannot be stopped.

[i-Pedal indicator will illuminate on
instrument cluster.
CAUTION
When the vehicle is stopped or parked by
i-Pedal on steep hills, be sure to also press
the brake pedal.
To deactivate:

[The i-Pedal is deactivated when the
driver turns off the vehicle. When the
vehicle is turned on, the regenerative
braking is set to be on level 3.

[The i-Pedal is turned off and the
regenerative braking changes to level
3 when the gear is shifted to R.
Limitations
The vehicle may move even if one pedal
driving is normally operated. Therefore,
the driver should be careful to stop
the vehicle by this function under
circumstances as follows:
-Driving on icy, snowy, wet, sandy, muddy
roads, manhole/pit hole surfaces
-Wheels not aligned
-Conditions in which wheel slip or spin
occurs
-On heavy loading
-By leaning left of right
-Under bad tire wear
-Driving uphill or downhill
-Driving where the slope starts or ends
-By repeating stop and go on ramp

6-30
Driving Your Vehicle
Releasing the parking brake
ORG3EV061024
To release EPB (Electronic Parking
Brake):
1. Press the Start/Stop button to the ON
or START position.
2. Press the EPB switch while depressing
the brake pedal.
Make sure the Parking Brake warning
light goes off.
To release EPB (Electronic Parking Brake)
automatically:

[Gear in P (Park)
With the vehicle running depress the
brake pedal and shift out of P (Park) to
R (Reverse) or D (Drive).

[Gear in N (Neutral)
With the vehicle running depress
the brake pedal and shift out of N
(Neutral) to R (Reverse) or D (Drive).

[Satisfy the following conditions
1. Ensure seat belts are fastened and the
doors, hood and trunk are closed.
2. With the vehicle running, depress the
brake pedal and shift out of P (Park) to
R (Reverse) or D (Drive).
3. Depress the accelerator pedal.
Make sure the Parking Brake warning
light goes off.
Information

[For the Middle East, EPB is released
regardless of seat belt fastening.

[For your safety, you can engage EPB
even though the Vehicle Stop/Start
button is in the OFF position (only if
battery power is available), but you
cannot release it.

[For your safety, depress the brake
pedal and release the parking brake
manually with the EPB switch when
you drive downhill or when backing up
the vehicle.
NOTICE

[If the Parking Brake warning light is
still on even though the EPB has been
released, have the system checked
by an authorized retailer of Genesis
Branded products.

[Do not drive your vehicle with EPB
applied. It may cause excessive brake
pad and brake rotor wear.

6-31
06
Warning messages
ORG3EV061038L
To release EPB, fasten seatbelt, close door,
hood and trunk

[If you try to drive with EPB applied, a
warning will sound and a message will
appear.

[If the driver's seat belt is unfastened
and the hood or trunk is opened, a
warning will sound and a message will
appear.

[If there is a problem with the vehicle,
a warning may sound and a message
may appear.
If the situation occurs, depress the brake
pedal and release EPB by pressing the
EPB switch.
WARNING

[Whenever leaving the vehicle or
parking, always come to a complete
stop and continue to depress the
brake pedal.
Shift the gear into P (Park), pull the
EPB switch, and press the Start/Stop
button to the OFF position. Take
the Key with you when leaving the
vehicle.
Vehicles not fully engaged in P (Park)
with the parking brake set are at risk
for moving inadvertently and causing
injury to yourself or others.

[NEVER allow anyone who is
unfamiliar with the vehicle to touch
the EPB switch. If EPB is released
unintentionally, serious injury may
occur.

[Only release EPB when you are
seated inside the vehicle with your
foot firmly on the brake pedal.

6-53
06
Active noise control-road helps reduce
noise caused while driving.
The system may not operate properly in
the following conditions:

[Any of the window is open

[Any of the door is open

[The trunk is open

[Vehicle’s microphone and speaker is
blocked by loads
System Malfunction
OJX1069055L
When Active noise control-road is not
working properly, this warning message
will appear on the cluster LCD display. If
this occurs, have the system inspected
by an authorized retailer of Genesis
Branded products.
$&7,9(12,6(&21752/

7-131
07
Off conditions

[Press the Parking/View button (1)
again, the image will turn off.

[When vehicle speed is above 9 mph
(15 km/h) with the gear in D (Drive),
Surround View Monitor will turn off
and the screen will change back to the
previous infotainment system screen.
Although you drive below 9 mph (15
km/h) again, Surround View Monitor
will not turn on.

[Press one of the infotainment system
button (3), the screen will change to
the infotainment system screen.

[Shift the gear to P (Park), the image
will turn off.
Rear view
The rear image is displayed on the screen
when the gear is in P (Park) to assist in
parking. The rear view has a top view/
rear view/side view/3D view.
Operating conditions

[Shift the gear to R (Reverse), the rear
view will appear on the screen.

[Press the Parking/View button (1)
while the gear is in P (Park), the rear
view will appear on the screen.
Off conditions

[The image cannot be turned off when
the gear is in R (Reverse).

[Shift the gear from R (Reverse) to P
(Park), the image will turn off.

[Press the Parking/View button (1)
again while the gear is in P (Park) with
the image on the screen.
6XUURXQG9LHZ0RQLWRU
Malfunction and Limitations
Surround View Monitor malfunction
When Surround View Monitor is not
working properly, or the screen flickers,
or the camera image does not display
properly, have the vehicle inspected by
an authorized retailer of Genesis Branded
products.
Limitations of Surround View
Monitor

[When the vehicle is stopped for a long
time in winter or when the vehicle is
parked in an indoor parking lot, the
exhaust fumes may temporarily blur
the image.

[The screen may be displayed
abnormally, and an icon will appear at
the top left side of the screen under
the following circumstances:
-The trunk is opened
-The driver or front passenger door
is opened
-The side view mirror is folded

7-151
07
5HYHUVH3DUNLQJ&ROOLVLRQ
$YRLGDQFH$VVLVW2SHUDWLRQ
Operating conditions
If ‘Rear Active Assist’ or ‘Rear Warning
Only’ is set from the Settings menu,
Reverse Parking Collision-Avoidance
Assist will be in the ready status when
the following conditions are satisfied:
-The trunk is closed
-The gear is shifted to R (Reverse)
-Vehicle speed is below 6 mph (10
km/h)
-Reverse Parking Collision-Avoidance
Assist components such as the rear
view camera and the rear ultrasonic
sensors are in normal conditions
When Reverse Parking Collision-
Avoidance Assist activates, a line
appears behind the vehicle image in the
instrument cluster.
Reverse Parking Collision-Avoidance
Assist operates only once after the gear
is shifted to R (Reverse). To reactivate
Reverse Parking Collision-Avoidance
Assist, shift the gear from another gear
to R (Reverse).
ORG3EV071067
Rear Active Assist

[If Reverse Parking Collision-Avoidance
Assist detects a risk of collision with
a pedestrian or an object, Reverse
Parking Collision-Avoidance Assist
will warn the driver with an audible
warning and warning message on the
cluster. When Rear View Monitor is
operating, a warning will appear on
the infotainment system screen.

[If Reverse Parking Collision-Avoidance
Assist detects an imminent collision
with a pedestrian or an object behind
the vehicle, Reverse Parking Collision-
Avoidance Assist will assist you with
braking. The driver needs to pay
attention and apply the brakes as the
brake assist will last for 5 minutes.
The driver must immediately depress
the brake pedal and check vehicle
surroundings.

[Brake control will end when:
-The gear is shifted to P (Park) or D
(Drive).
-The driver depresses the brake
pedal with sufficient power
-Braking assist has last for
approximately 5 minutes

[The warning will turn off when:
-The driver shifts the gear to P (Park),
N (Neutral), or D (Drive)
Rear Warning Only

[If Reverse Parking Collision-Avoidance
Assist detects a risk of collision with
a pedestrian or an object, Reverse
Parking Collision-Avoidance Assist
will warn the driver with an audible
warning and warning message on the
cluster. When Rear View Monitor is
operating, a warning will appear on
the infotainment system screen.

[If ‘Rear Warning Only’ is selected,
braking will not be assisted.

[The warning will turn off when the
gear is shifted to P (Park), N (Neutral)
or D (Drive).

7-163
07
Remote Operation function operation
status
Operation
status6PDUWNH\/('+D]DUG
warning
light
Under
controlGreen LED
continuously
blinks-
PauseRed LED
continuously
blinksBlinks
OffRed LED
illuminates for
4 seconds and
then turns offBlinks 3
times and
turns off
CompleteGreen LED
illuminates for
4 seconds and
then turns offBlinks 1
time and
turns off
ÃOperation status by the hazard
warning light may not be applicable
based on the regulation of your
country.
ÃIf the smart key is not within the
operating range from the vehicle
(approximately 13 ft. (4m)), the
smart key LED will not illuminate or
blink. Use the smart key within the
operating range.
How to turn off Remote Operation
function while operating

[Press the Parking/View () button
while the infotainment system screen
guides the driver using method 2.

[Shift the gear except to P (Park)
while the infotainment system screen
guides the driver using method 2.

[Press the Parking Safety (
) button
or select ‘Cancel’ on the infotainment
system screen.

[Press the Remote Start (
) button
on the smart key while the vehicle is
being controlled by Remote Operation
function. Remote Operation function
will turn off. At this time, the vehicle
will turn off.

[Get on the vehicle with the smart
key. Remote Operation function will
turn off. At this time, the vehicle will
remain on.
The function will pause in the following
conditions when:

[There is a pedestrian, animal or object
in the direction the vehicle is moving

[The door or trunk is open

[The Forward (
) or Backward ()
button is not continuously pressed

[Simultaneously pressing multiple
buttons on a smart key

[The smart key is not operated within
13 ft. (4 m) from the vehicle

[Button of another smart key is pressed
in addition to the operating smart key

[Blind-Spot Collision-Avoidance
Assist or Rear Cross-Traffic Collision-
Avoidance Assist operates while the
vehicle is being controlled in the
reverse direction.

7-172
Driver Assistance System
The function will pause in the
following conditions when:

[Smart Parking
-There is a pedestrian, animal or
object in the direction the vehicle is
moving
-The door or trunk is open
-The driver’s seat belt is not fastened
-Blind-Spot Collision-Avoidance
Assist or Rear-Cross Traffic
Collision-Avoidance Assist operates
while the vehicle is being controlled
in the reverse direction
-The Parking/View (
) button is
not continuously pressed
-The vehicle is stopped by
depressing the brake pedal

[Remote Smart Parking
-There is a pedestrian, animal or
object in the direction the vehicle is
moving
-The door or trunk is open
-The Forward (
) or Backward ()
button is not continuously pressed
-Simultaneously pressing multiple
buttons on a smart key
-The smart key is not operated within
13 ft. (4 m) from the vehicle
-Button of another smart key is
pressed in addition to the operating
smart key
-Blind-Spot Collision-Avoidance
Assist or Rear-Cross Traffic
Collision-Avoidance Assist operates
while the vehicle is being controlled
in the reverse direction
When Parking function is paused, the
vehicle will automatically stop. If the
condition that made the function to
pause disappears, the function may
operate again.
The function will cancel in the
following conditions when:

[Smart Parking
-The steering wheel is steered
-The gear is shifted while the vehicle
is moving
-Operating EPB while the vehicle is
moving
-The hood is open
-The driver opens the door with the
seatbelt unfastened
-Rapid acceleration occurs
-Vehicle skid occurs
-The wheel is stuck by an obstacle
and cannot move
-There are pedestrians, animals or
objects at the front and rear of the
vehicle at the same time
-Approximately 3 minutes and 50
seconds has passed after Smart
Parking function has started to
operate
-The slope of the road exceeds the
operational range
-The function is paused for more
than 1 minute
-The steering wheel, gearshift,
braking, and drive controls are not
working properly
-ABS, TCS or ESC system operates
due to slippery road conditions
-The charging door is open
When Smart Parking function is
canceled, the vehicle will automatically
stop, shift the gear to P (Park) and
engage EPB (Electronic Parking Brake).

7-176
Driver Assistance System
How to turn off Smart function while
operating

[Press the Parking/View () button
in the following stage:
-Checking space
-Select exit direction

[Shift the gear to R (Reverse) in the
following stage:
-Checking space
-Select exit direction

[Press the Parking Safety (
) button
or select ‘Cancel’ on the infotainment
system screen to turn off Exit
function.

[While Smart Exit function is operating,
if the vehicle is stopped by depressing
the brake pedal, and the gear is
shifted, Exiting function will turn off.
At this time, EPB (Electronic Parking
Brake) will not be engaged.
The function will pause in the following
conditions when:

[There is a pedestrian, animal or object
in the direction the vehicle is moving

[The door or trunk is open

[The driver’s seat belt is not fastened

[Blind-Spot Collision-Avoidance
Assist or Rear-Cross Traffic Collision-
Avoidance Assist operates while the
vehicle is being controlled in the
reverse direction

[The Parking/View (
) button is not
continuously pressed

[The vehicle is stopped by depressing
the brake pedal
When Exit function is paused, the vehicle
will stop. If the condition that made
the function to pause disappears, the
function may operate again.
The function will cancel in the following
conditions when:

[Smart Exit
-The steering wheel is steered
-The gear is shifted while the vehicle
is moving
-Operating EPB while the vehicle is
moving
-The hood is open
-The driver opens the door with the
seatbelt unfastened
-Rapid acceleration occurs
-Vehicle skid occurs
-The wheel is stuck by an obstacle
and cannot move
-There are pedestrians, animals or
objects at the front and rear of the
vehicle at the same time
-Approximately 3 minutes and 50
seconds has passed after Smart Exit
function has started to operate
-The slope of the road exceeds the
operational range
-The function was paused for more
than 1 minute
-The steering wheel, gearshift,
braking, and drive controls are not
working properly
-ABS, TCS or ESC system operates
due to slippery road conditions
-The charging door is open
-The vehicle is utility mode
When Smart Exit function is canceled,
the vehicle will automatically stop, shift
the gear to P (Park) and engage EPB
(Electronic Parking Brake).