Side GENESIS G90 2023 Owners Manual

6-23
06
Power-Assist Brakes
Your vehicle has power-assisted brakes
that adjust automatically through normal
usage.
In the event of a vehicle power failure,
the power assist for the brakes will not
work. You can still stop your vehicle, but
it will require greater force and increased
pedal travel than normal. The stopping
distance, however, will be longer than
with power brakes.
Information

[When the brake pedal is depressed
under certain driving conditions
or weather conditions, you may
temporarily hear a noise. This is
normal and does not indicate a problem
with your brakes.

[While driving on a road with deicing
chemicals, brake noise or abnormal
tire wear may occur due to deicing
chemicals. In a safe traffic condition,
additionally apply the brakes to remove
deicing chemicals on the brake discs
and pads.
WARNING
Take the following precautions:

[Do not drive with your foot resting
on the brake pedal. This will create
abnormal high brake temperatures,
excessive brake lining and pad wear,
and increased stopping distances.

[When descending down a long or
steep hill, use the paddle shifter
and manually downshift to a
lower gear in order to control your
speed without using the brake
pedal excessively. Applying the
brakes continuously will cause
the brakes to overheat and could
result in a temporary loss of braking
performance.

[Wet brakes may impair the vehicle's
ability to safely slow down; the
vehicle may also pull to one side
when the brakes are applied.
Applying the brakes lightly will
indicate whether they have been
affected in this way. Always test your
brakes in this fashion after driving
through deep water. To dry the
brakes, lightly tap the brake pedal to
heat up the brakes while maintaining
a safe forward speed until brake
performance returns to normal.
Avoid driving at high speeds until the
brakes function correctly.
Disc Brakes Wear Indicator
When your brake pads are worn and new
pads are required, you will hear a high
pitched warning sound from your front
or rear brakes. You may hear this sound
come and go or it may occur whenever
you depress the brake pedal.
NOTICE
To avoid costly brake repairs, do not
continue to drive with worn brake pads.
Information
Always replace brake pads as complete
front or rear axle sets.
BRAKING SYSTEM

6-26
Driving Your Vehicle
Warning messages
ORS061053L
To release EPB, fasten seatbelt, close door,
hood and trunk

[If you try to drive with EPB applied, a
warning will sound and a message will
appear.

[If the driver's seat belt is unfastened
and the engine hood or trunk is
opened, a warning will sound and a
message will appear.

[If there is a problem with the vehicle,
a warning may sound and a message
may appear.
If the situation occurs, depress the brake
pedal and release EPB by pressing the
EPB switch.
WARNING

[Whenever leaving the vehicle or
parking, always come to a complete
stop and continue to depress the
brake pedal.
Shift the gear into P (Park), pull the
EPB switch, and press the Engine
Start/Stop button to the OFF
position. Take the Key with you when
leaving the vehicle.
Vehicles not fully engaged in P (Park)
with the parking brake set are at risk
for moving inadvertently and causing
injury to yourself or others.

[NEVER allow anyone who is
unfamiliar with the vehicle to touch
the EPB switch. If EPB is released
unintentionally, serious injury may
occur.

[Only release EPB when you are
seated inside the vehicle with your
foot firmly on the brake pedal.
NOTICE

[Do not apply the accelerator pedal
while the parking brake is engaged.
If you depress the accelerator pedal
with EPB engaged, a warning will
sound and a message will appear.
Damage to the parking brake may
occur.

[Driving with the parking brake on
can overheat the braking system and
cause premature wear or damage
to brake parts. Make sure EPB is
released and the Parking Brake
warning light is off before driving.
Information

[A clicking sound may be heard while
operating or releasing the EPB. These
conditions are normal and indicate that
EPB is functioning properly.

[When leaving your keys with a parking
attendant or assistant, make sure to
inform him/her how to operate EPB.

6-38
Driving Your Vehicle
Good Braking Practices
WARNING
Whenever leaving the vehicle or
parking, always come to a complete
stop and continue to depress the brake
pedal. Shift the gear to the P (Park)
position, then apply the parking brake,
and press the Engine Start/Stop button
to the OFF position.
Vehicles parked with the parking brake
not applied or not fully engaged may
roll inadvertently and may cause injury
to the driver and others. ALWAYS apply
the parking brake before exiting the
vehicle.
Wet brakes can be dangerous! The
brakes may get wet if the vehicle is
driven through standing water or if it
is washed. Your vehicle will not stop as
quickly if the brakes are wet. Wet brakes
may cause the vehicle to pull to one side.
To dry the brakes, apply the brakes
lightly until the braking action returns to
normal. If the braking action does not
return to normal, stop as soon as it is safe
to do so and we recommend that you call
an authorized retailer of Genesis Branded
products for assistance.DO NOT drive with your foot resting on
the brake pedal. Even light, but constant
pedal pressure can result in the brakes
overheating, brake wear, and possibly
even brake failure.
If a tire goes flat while you are driving,
apply the brakes gently and keep the
vehicle pointed straight ahead while you
slow down. When you are moving slowly
enough for it to be safe to do so, pull off
the road and stop in a safe location.
Keep your foot firmly on the brake pedal
when the vehicle is stopped to prevent
the vehicle from rolling forward.

6-45
06
ORS061019
The Multi-chamber air suspension uses
the air spring containing compressed
air to adjust and maintain the vertical
height of the vehicle both manually or
automatically, according to number of
passengers and load capacity. It also
controls the valve inside the air spring
to adjust stiffness of the air spring and
damper to maximize driving comforts.
Each driving mode provides different
ride comforts.
Vehicle Height Adjustment

[Press the vehicle height adjustment
button to adjust the height. Pressing
the button will raise the vehicle body
and the indicator light illuminates.
Pressing the button again will return
the vehicle height to its original
position and the indicator light turns
off.
[If the vehicle is driving in high speed,
the vehicle height adjustment is set
to automatic mode and the vehicle
height will return to its original
position although you press the
button.
-While above a certain speed, the
height will be automatically set
depending on the driving speed.
-Vehicle height may differ depending
on the drive mode.

[Depending on vehicle condition,
height adjustment will not operate or
stop operating, and the indicator light
blinks.
-When the Multi-chamber air
suspension is malfunctioning
-When the vehicle is lifted up.
-When the vehicle is not stable due
to a sudden brake or acceleration.
-When the air compressor is
overheated.
-When the vehicle is not parked on a
level ground.

[Vehicle height may automatically be
adjusted after 2/4/8/16 hours from
turning off the engine. It is due to the
changes in air temperature.
CAUTION
If the compressor air filter under the
vehicle body is submerged in water,
do not operate the air suspension.
Moisture inflow may damage the
system.
08/7,

6-46
Driving Your Vehicle
Multi-Chamber Air Suspension
Malfunction
OJWEV061048L
This message is displayed when there is
a malfunction with the Multi-chamber
air suspension system. Have the vehicle
inspected by an authorized retailer of
Genesis Branded products.
CAUTION

[When adjusting vehicle height, check
if there are any obstacles below or
above the vehicle.

[If air inside the suspension is
discharged, a warning message
will be displayed. If so, stop driving
and use a towing vehicle. Since
the vehicle height will be very low,
projections on the road may damage
the vehicle. See ‘Towing when the
air suspension malfunctions’ before
towing the vehicle.
Information

[Operating the air suspension may
cause a little noise when charging and
discharging the air.

[Adjusted vehicle height may vary
depending on the temperature and
surrounding environment.

[When the suspension warning message
is displayed, the system enables safe
mode to prevent secondary failure
and the vehicle performance may be
displayed differently.

[When the vehicle is parked on a slope,
or when the vehicle is in unstable
condition due to sudden acceleration,
deceleration or steering, vehicle height
adjustment becomes temporarily
disabled. If the vehicle escapes from
such dangerous situation, vehicle height
adjustment is enabled again.

[When the vehicle is lifted up with a
lift or jack, height adjustment may be
disabled to protect the system. If the
vehicle engine is started or you start
driving, the function is enabled again.

[Leaving the vehicle parked for long
time may lower the vehicle height. The
vehicle height returns to its original
position when the engine is started.

[If the battery is either overcharged or
discharged, vehicle height adjustment
is disabled to protect the system and a
temporary warning message may be
displayed.

[If the vehicle height adjustment is
operated repeatedly, the function may
be temporarily disabled due to the
overheated compressor. It is to prevent
the breakdown of related parts.

6-48
Driving Your Vehicle
Towing When the Air Suspension
Malfunction
ORS061020L
Driving while the suspension is
malfunctioning and the air inside the
suspension is discharged may damage
the vehicle.
Use the towing vehicle and we
recommend that you have the system
checked by an authorized retailer of
Genesis Branded products.
Use only flatbed tow trucks. Other
towing methods may damage the
vehicle.
ORS061021L
The flatbed tow truck must be a safety
loader type which has a loading angle M
less than 6º.
Towing with a loading angle larger than
6º may damage the vehicle.

6-49
06
Idle Stop and Go helps reduce fuel
consumption by automatically shutting
down the engine, when the vehicle is
at a standstill (for example, red stop
light, stop sign, and traffic jam) subject
to certain prerequisite conditions being
satisfied as listed below.
The engine is automatically started upon
satisfying the starting conditions.
ISG system is always active, when the
engine is running.
Information
When the engine is automatically started
by ISG system, warning lights (for
example, ABS, ESC, ESC OFF, MDPS,
and parking brake warning light) may
illuminate for a few seconds due to low
battery voltage.
However, it does not indicate a
malfunction with ISG system.
ISG System Operation
Prerequisite for activation
ISG system operates in the following
situations.

[The driver's seatbelt is fastened

[The driver's door and hood are closed

[The battery sensor is activated and
the battery is sufficiently charged

[Outside temperature is not too low or
too high

[The vehicle is driven over a constant
speed and stops

[The climate control system satisfies
the conditions

[The vehicle is sufficiently warmed up

[ISG related parts are working properly

[The incline is gradual

[The steering wheel is turned less than
180 degrees and then the vehicle
stops
Information
ORS062070C
ISG system is not activated, when the
prerequisites to activate the ISG system
are unsatisfied.
Auto stop
When ISG is on the engine will be
stopped automatically when both of the
following occurs:
1. Vehicle speed decreases to 0mph (0
km/h) full stop condition.
2. Brake pedal is depressed and gear is
in D (Drive) or N (Neutral).
The Auto Stop (
) indicator illuminates
in green on the instrument cluster, when
the engine stops.
The gasoline 3.5 turbo 48 V electric
supercharger vehicle may automatically
shut down the engine when the vehicle
speed is below 16 mph (25 km/h) with
the brake pedal depressed. At this time,
the ISG indicator lights up in green on
the instrument cluster.
Information
Idle stop cannot reoccur again until the
vehicle speed goes above 3 mph (5 km/h)
and then returns again to the automatic
stop conditions as previously mentioned.
,'/(6723$1'*2

6-55
06
Coasting Release Conditions
The Coasting function will be
automatically released when the
following conditions are met.

[Comfort or Sport is selected for
driving mode

[The driver uses the paddle shifter

[Smart Cruise Control is activated (Set
speed appears on the cluster)

[The vehicle’s speed exceeds 30~100
mph (50~160 km/h) range

[The road gradient is under -5% or over
+5%

[If the distance between the vehicle
ahead is too close or the relative
speed changes momentarily in Smart
mode

[If lane change is predicated in Smart
mode (for example, the turn signal is
turned ON or a LKA warning appears
due to steering wheel control, etc.)
Information
It is recommended to turn off the
Coasting function if you are driving under
frequently stop-and-go condition. Change
the drive mode to Comfort or Sport or
deselect Coasting from the infotainment
system screen.
NOTICE

[If the accelerator pedal is pressed
quickly for accelerating with the
Coasting function in operation,
acceleration may occur after the
engagement of the clutch inside the
transmission. In turn, the driver may
continue to feel acceleration even
after the system is turned off.

[Driving with the Coasting function
off may be required in some cases
since the engine brake is not applied
while the Coasting function is
operating.

[Operating the infotainment system
screen to activate or deactivate
the Coasting function while driving
may be dangerous as the driver’s
attention is dispersed.

6-68
Driving Your Vehicle
Driving in the Rain
Rain and wet roads can make driving
dangerous. Here are a few things to
consider when driving in the rain or on
slick pavement:

[Slow down and allow extra following
distance. A heavy rainfall makes
it harder to see and increases the
distance needed to stop your vehicle.

[Turn OFF your Smart Cruise Control

[Replace your windshield wiper blades
when they show signs of streaking or
missing areas on the windshield.

[Be sure your tires have enough tread.
If your tires do not have enough depth
of tire tread, making a quick stop on
wet pavement can cause a skid and
possibly lead to an accident. See “Tire
Tread” section in chapter 9.

[Turn on your headlights to make it
easier for others to see you.

[Driving too fast through large puddles
can affect your brakes. If you must go
through puddles, try to drive through
them slowly.

[If you believe your brakes may be wet,
apply them lightly while driving until
normal braking operation returns.
Hydroplaning
If the road is wet enough and you are
going fast enough, your vehicle may
have little or no contact with the road
surface and actually ride on the water.
The best advice is SLOW DOWN when
the road is wet.
The risk of hydroplaning increases as the
depth of tire tread decreases, refer to
“Tire Tread” section in chapter 9.
Driving in Flooded Areas
Avoid driving through flooded areas
unless you are sure the water is no
higher than the bottom of the wheel hub.
Drive through any water slowly. Allow
adequate stopping distance because
brake performance may be reduced.
After driving through water, dry the
brakes by gently applying them several
times while the vehicle is moving slowly.
Highway Driving
Tires
Adjust the tire inflation, as specified.
Under-inflation may overheat or damage
the tires.
Do not install worn-out or damaged tires,
which may reduce traction or fail the
braking operation.
Information
Never over-inflate your tires above the
maximum inflation pressure, as specified
on your tires.
Fuel, engine coolant and engine oil
Driving at higher speeds on the highway
consumes more fuel and is less efficient
than driving at a slower, more moderate
speed. Maintain a moderate speed in
order to conserve fuel when driving on
the highway.
Be sure to check both the engine coolant
level and the engine oil before driving.
Drive belt
A loose or damaged drive belt may
overheat the engine.

6-71
06
Tire chains
ORS061025L
Since the sidewalls on some radial tires
are thinner than other types of tires,
they may be damaged by mounting
certain types of tire chains on them.
Do not mount tire chains on vehicles
equipped with aluminum wheels; if
possible use AutoSock® (fabric snow
chain or similar). Install AutoSock® after
reviewing the instructions provided
with AutoSock®. Damage to your vehicle
caused by improper use of fabric snow
chains are not covered by your vehicle
manufacturer's warranty.
Information
AutoSock® is a Registered trademark of
AutoSock.
WARNING
The use of AutoSock® (fabric snow
chain) may adversely affect vehicle
handling:

[Drive less than 20 mph (30 km/h)
or the AutoSock® manufacturer’s
recommended speed limit,
whichever is lower.

[Drive carefully and avoid bumps,
holes, sharp turns, and other road
hazards, which may cause the
vehicle to bounce.

[Avoid sharp turns or locked wheel
braking.
Disabling Rear Wheel Steering system to
install snow chains
ORS061036L
If the Rear Wheel Steering system is
applied, disable the system to protect the
vehicle when snow chains are installed.
6HOHFW
S6HWXS