lock GENESIS G90 2023 Owners Manual

9-6
Maintenance
Owner Maintenance Schedule
When you stop for fuel:

[Check the coolant level in the engine
coolant reservoir or the liquid-cooled
intercooler coolant reservoir.

[Check the windshield washer fluid
level.

[Check for low or under-inflated tires.
WARNING
Be careful when checking your coolant
level if the motor compartment is hot.
This may result in coolant being blown
out of the opening and cause serious
burns and other injuries.
While operating your vehicle:

[Note any changes in the sound of the
exhaust or any smell of exhaust fumes
in the vehicle.

[Check for vibrations in the steering
wheel. Notice if there is any increased
steering effort or looseness in the
steering wheel, or change in its
straight-ahead position.

[Notice if your vehicle constantly turns
slightly or “pulls” to one side when
traveling on smooth, level road.

[When stopping, listen and check for
unusual sounds, pulling to one side,
increased brake pedal travel or “hard-
to-push” brake pedal.

[If any slipping or changes in the
operation of your transmission occurs,
check the transmission fluid level.

[Check the automatic transmission P
(Park) function.

[Check the parking brake.

[Check for fluid leaks under your
vehicle (water dripping from the air
conditioning system during or after
use is normal).
At least monthly:

[Check coolant level in the engine
coolant reservoir.

[Check the operation of all exterior
lights, including the stoplights, turn
signals and hazard warning flashers.

[Check the inflation pressures of all
tires including the spare for tires that
are worn, show uneven wear, or are
damaged.

[Check for loose wheel lug nuts.
At least twice a year: (for example,
every Spring and Autumn)

[Check radiator, heater and air
conditioning hoses for leaks or
damage.

[Check windshield washer spray and
wiper operation. Clean wiper blades
with a clean cloth dampened with
washer fluid.

[Check headlight alignment.

[Check muffler, exhaust pipes, shields
and clamps.

[Check the seat belts for wear and
function.
At least once a year:

[Clean body and door drain holes.

[Lubricate door hinges and hood
hinges.

[Lubricate door and hood locks and
latches.

[Lubricate door rubber weather strips.

[Check the air conditioning system.

[Inspect and lubricate automatic
transmission linkage and controls.

[Clean the battery and terminals.

[Check the brake fluid level.

9-15
09
ENGINE OIL
Suspension Mounting Bolts
Check the suspension connections for
looseness or damage. Retighten to the
specified torque.
Steering Gear box, Linkage &
Boots/Lower Arm Ball Joint
With the vehicle stopped and the engine
off, check for excessive free-play in the
steering wheel. Check the linkage for
bends or damage. Check the dust boots
and ball joints for deterioration, cracks,
or damage.
Replace any damaged parts.
Drive Shafts and Boots
Check the drive shafts, boots and clamps
for cracks, deterioration, or damage.
Replace any damaged parts and, if
necessary, repack the grease.
Air Conditioning Refrigerant
Check the air conditioning lines and
connections for leakage and damage.
Checking the Engine Oil Level
Engine oil is used for lubricating,
cooling, and operating various hydraulic
components in the engine. Engine oil
consumption while driving is normal,
and it is necessary to check and refill the
engine oil regularly. Also, check and refill
the oil level within the recommended
maintenance schedule to prevent
deterioration of oil performance.
Check the engine oil following the below
procedure.
1. Follow all of the oil manufacturer’s
precautions.
2. Be sure the vehicle is on the level
ground in P (Park) with the parking
brake set and the wheels blocked.
3. Turn the engine on and warm
the engine up until the coolant
temperature reaches a constant
normal temperature.
4. Turn the engine off, remove the oil
filler cap and pull the dipstick out.
Wait for 15 minutes for the oil to return
to the oil pan.
5. Wipe the dipstick clean and re-insert
it fully.

9-19
09
Information
The coolant level is influenced by the
engine temperature. Before checking or
refilling the coolant, turn the engine off.
WARNING
The electric motor for the
cooling fan may continue to
operate or start up when the
engine is not running and can
cause serious injury. Keep
hands, clothing and tools away
from the rotating fan blades of
the cooling fan.
Always turn off the vehicle unless the
vehicle has to be inspected with the
engine on. Be cautious as the cooling
fan may operate if the negative (-)
battery terminal is not disconnected.
WARNING
Make sure the coolant cap is properly
closed after refilling coolant. Otherwise
the engine could be overheated while
driving.
„Engine compartment front view
ORG3EV091045
1. Check if the coolant cap label is
straight in front.
ORG3EV091043
2. Make sure that the tiny protrusions
inside the coolant cap are securely
interlocked.

9-24
Maintenance
Filter Inspection
The cabin air filter should be replaced
according to the Maintenance Schedule.
If the vehicle is operated in severely air-
polluted cities or on dusty rough roads
for a long period, it should be inspected
more frequently and replaced sooner.
Replace the cabin air filter by following
the procedure below and be careful to
avoid damaging other components.
Filter Replacement
ORS091009
1. Open the glove box and remove the
support rod M.
ORS091010
2. Remove the stoppers on both sides to
allow the glove box to hang freely on
the hinges.
ORS092011N
3. Press and hold the lock M on the left
side of the cover.
4. Pull out N the cover
5. Replace the cabin air filter.
6. Reassemble in the reverse order of
disassembly.
CABIN AIR FILTER

9-25
09
Engine Compartment
ORS091012
ORS092054N
1. Open the engine hood and remove
the cover of the air conditioning
assembly to locate the air filter.
2. Open the engine hood and remove
the cover of air conditioning unit.
3. Press and hold the lock M on the left
side of the cover.
4. Pull out N the cover
5. Replace the cabin air filter.
6. Reassemble in the reverse order of
disassembly.
NOTICE
ORS091061
A : Glove box,
B : Engine compartment
Install a new cabin air filter in the
correct direction to prevent noise and
reduce effectiveness.

[Glove box: Install with the arrow
V\PEROIDFLQJGRZQZDUG

9-32
Maintenance
NOTICE

[AGM battery
-Absorbent Glass Matt (AGM)
batteries are maintenance-free
and we recommend that the
AGM battery be serviced by an
authorized retailer of Genesis
Branded products. For charging
your AGM battery, use only fully
automatic battery chargers that
are specially developed for AGM
batteries.
-When replacing the AGM battery,
we recommend that you use
parts for replacement from an
authorized retailer of Genesis
Branded products.
-Do not open or remove the cap on
top of the battery. This may cause
leaks of internal electrolyte that
could result in severe injury.

[Lithium battery (if equipped)
-Do not jump start other vehicles.
The lithium polymer type battery
installed in your vehicle may be
damaged.
-Do not connect external electrical
devices to the battery.
-When replacing the lithium
polymer battery, have the battery
replaced at an authorized retailer
of Genesis Branded products.
By jump starting
After a jump start from a good battery,
drive the vehicle for 20-30 minutes
before it is shutoff. The vehicle may
not restart if you shut it off before the
battery had a chance to adequately
recharge. See “Jump Starting” in chapter
8 for more information on jump starting
procedures.
Information
An inappropriately disposed
battery can be harmful to the
environment and human health.
Dispose of the battery according
to your local law(s) or regulation.
Reset Items
The following items may need to be reset
after the battery has been discharged or
the battery has been disconnected.

[Fuel economy/Driving info/Since
refueling/Accumulated info (items in
Normal view) (see chapter 4)

[Integrated memory system (see
chapter 5)

[Power window (see chapter 5)

[Sunroof (see chapter 5)

[Power trunk (see chapter 5)

[Climate control system (see chapter 5)

[Rear door window shade (see chapter
5)

[Clock (see Infotainment system
manual)

[Infotainment system (see
Infotainment system manual)

9-33
09
WARNING
Tire failure may cause loss of
vehicle control resulting in an
accident. To reduce risk of SERIOUS
INJURY or DEATH, take the
following precautions:

[Inspect your tires monthly for
proper inflation as well as wear
and damage.

[The recommended cold tire
pressure for your vehicle can be
found in this manual and on the
tire label located on the driver’s
side center pillar. Always use a
tire pressure gauge to measure
tire pressure. Tires with too
much or too little pressure wear
unevenly causing poor handling.

[Check the pressure of the
spare every time you check the
pressure of the other tires on
your vehicle.

[Replace tires that are worn, show
uneven wear, or are damaged.
Worn tires can cause loss of
braking effectiveness, steering
control, or traction.

[ALWAYS replace tires with the
same size, type, construction and
tread pattern as each tire that
was originally supplied with this
vehicle. Using tires and wheels
other than the recommended
sizes could cause unusual
handling characteristics, poor
vehicle control, or negatively
affect your vehicle’s Anti-Lock
Brake System (ABS) resulting in a
serious accident.
Tire Care
For proper maintenance, safety, and
maximum fuel economy, you must
always maintain recommended
tire inflation pressures and stay
within the load limits and weight
distribution recommended for your
vehicle.
ORS012024N
All specifications (sizes and
pressures) can be found on a label
attached to the driver’s side center
pillar.
Recommended Cold Tire
Inflation Pressures
All tire pressures (including the
spare) should be checked when the
tires are cold. “Cold tires” means the
vehicle has not been driven for at
least three hours or driven less than
one mile (1.6 km).
Warm tires normally exceed
recommended cold tire pressures
by 4 to 6 psi (28 to 41 kPa). Do not
release air from warm tires to adjust
the pressure or the tires will be
under-inflated. For recommended
inflation pressure, refer to “Tire and
Wheels” section in chapter 2.
TIRES AND WHEELS

9-36
Maintenance
Wheel Alignment and Tire
Balance
The wheels on your vehicle were
aligned and balanced carefully at the
factory to give you the longest tire
life and best overall performance.
In most cases, you will not need to
have your wheels aligned again.
However, if you notice unusual tire
wear or your vehicle pulling one way
or the other, the alignment may need
to be reset.
If you notice your vehicle vibrating
when driving on a smooth road, your
wheels may need to be rebalanced.
NOTICE
Incorrect wheel weights can
damage your vehicle’s aluminum
wheels. Use only approved wheel
weights.
Tire Replacement
ORS091057
A : Tread wear indicator
If the tire is worn evenly, a tread wear
indicator will appear as a solid band
across the tread. This shows there is
less than 1/16 inch (1.6 mm) of tread
left on the tire. Replace the tire when
this happens.
Do not wait for the band to appear
across the entire tread before
replacing the tire.
WARNING
To reduce the risk of DEATH or
SERIOUS INJURY:

[Replace tires that are worn, show
uneven wear, or are damaged.
Worn tires can cause loss of
braking effectiveness, steering
control, and traction.

[Always replace tires with the
same size as each tire that was
originally supplied with this
vehicle. Using tires and wheels
other than the recommended
sizes could cause unusual
handling characteristics, poor
vehicle control, or negatively
affect your vehicle’s Anti-Lock
Brake System (ABS) resulting in a
serious accident.

[When replacing tires (or wheels),
it is recommended to replace
the two front or two rear tires (or
wheels) as a pair. Replacing just
one tire can seriously affect your
vehicle’s handling.

[Tires degrade over time, even
when they are not being used.
Regardless of the remaining
tread, Genesis Branded Vehicle
recommends that tires be
replaced after six (6) years of
normal service.

[Heat caused by hot climates or
frequent high loading conditions
can accelerate the aging process.
Failure to follow this warning
may cause sudden tire failure,
which could lead to a loss of
vehicle control resulting in an
accident.

9-50
Maintenance
Instrument panel fuse panel
Fuse NameFuse
RatingCircuit Protected
P/SEAT (PASS)225A Passenger Power Seat Module
S/HEATER
(PASS)25A Passenger Power Seat Module
A/BAG IND10A Overhead Console
UWB10ABLE Unit, Interior UBW Unit #1/#2/#3, Interior UBW Unit,
Rear UBW Unit LH/RH, Front UBW Unit LH/RH
P/SEAT (PASS)130A Passenger Power Seat Module
P/SEAT (DRV)130A Driver Power Seat Module
SUNROOF220A Sunroof Rear Rollo Controller
MODULE1310AElectro Chromic Mirror, Data Link Connector, Front A/C
Controller, A/C Control Module, AMP CCIC Keyboard,
Smart Phone Wireless Charger, Support AMP, LDC (IG1
Input), CCIC Head Unit, REAR Junction Block (LDC - IG1
Input), Driver/Passenger Power Seat Module, Rear Seat
CCS Module LH/RH, Rear Seat Heater Control Module LH/
RH, Rear Power Seat Module LH/RH, Rear Seat Console
Wireless Charger, Rear Seat Console UVC Lamp, Armrest
Touch Screen, AMP
MASSAGE SEAT
(FRT)15ADriver/Passenger Lumbar Support Unit, Passenger Foot
Massage Unit
S/HEATER
(DRV)25A Driver Power Seat Module
CURTAIN15A IBU
ADAS DRV110A ADAS Unit (Driving)
MODULE1410ADriver/Passenger Door Outside Handle, Rear Door Outside
Handle LH/RH
P/SEAT (DRV)225A Driver Power Seat Module
PRESAFETY
SEAT BELT110A Pre-Active Seat Belt Unit
SBCM (RR LH)20A Rear SBCM LH
P/WINDOW
(LH)30ADriver Safety Power Window Module, Rear Safety Power
Window Module LH
MODULE810AADAS Unit (Parking), Center Control Panel, CCIC Head Unit,
Rear Seat Console Tray Lamp, Rear Seat Console Remote
Control Switch, Instrument Cluster, Rear Seat Console UVC
Lamp
BRAKE SWITCH10A IBU, Stop Lamp Switch
SUNROOF120A Sunroof Glass Controller

9-51
09
Fuse NameFuse
RatingCircuit Protected
SBCM (DRV)20A Driver SBCM
CCU110A CCU
POWER
HANDLE15A Steering Tilt & Telescopic Unit
MODULE210AFront A/C Controller, Multifunction Switch, Head Lamp LH/
RH
MODULE910AMultifunction Switch, Data Link Connector, CCIC Keyboard,
Rain Sensor, Driver Power Window Switch, Driver Power
Outside Mirror Switch
CCU210A Stop Lamp Switch, CCU
A/C310AA/C Control Module, Front A/C Controller, Incar
Temperature Sensor, E/R Sub Junction Block (PTC Heater
#1/#2 Relay) Rear Junction Block (Rear Blower Relay)
MODULE310A IBU, IAU
IBU110A IBU, IAU
IBU210A IBU, BMS Control Module
E-SHIFTER210A Electronic ATM Shift Lever Dial
E-SHIFTER110A Electronic ATM Shift Lever Dial
MODULE1210ARear Corner Radar LH/RH, ECS Unit, Air ECS Unit, AWD
ECU, RWS Module, ADAS Unit (Parking), IBU, Crash Pad
Switch, Steering Tilt & Telescopic Unit, Front View Camera
(ADAS)
MODULE1110A Driver Power Window Switch, Multifunction Switch, IAU
AIR BAG215A SRS Control Module, Passenger Occupant Detection Sensor
AIR BAG115A SRS Control Module
MODULE1610AFront Console Mood Lamp #1/2, Garnish Lamp LH/RH,
Mood Lamp Unit, Roof Mood Lamp #1/2, Driver/Passenger
Door Garnish Mood Lamp, Rear Door Garnish Mood Lamp
LH/RH, ADAS Unit (Parking)
CLUSTER10A Instrument Cluster, Head-Up Display
MODULE1510A ADAS Unit (Driving)
Wireless DCU10A Domain Control Unit
MODULE510ARear Door Curtain, Rear Occupant Alert (ROA) Sensor,
Clock Spring, Front Console Switch, Active Air Flap Module,
Steering Tilt & Telescopic Unit