Side GENESIS G90 2023 Owners Manual

7-56
Driver Assistance System
6DIH([LW$VVLVWPDOIXQFWLRQDQG
Limitations
Safe Exit Assist malfunction
OJWEV071019L
When Safe Exit Assist is not working
properly, the ‘Check Blind-Spot Safety
system’ warning message will appear
on the instrument cluster for several
seconds, and the master (
) warning
light will illuminate on the instrument
cluster. If this occurs, have the vehicle
inspected by an authorized retailer of
Genesis Branded products.
OJWEV071021L
When the side view mirror warning
light is not working properly, the ‘Check
side view mirror warning light’ warning
message will appear on the instrument
cluster for several seconds, and the
master (
) warning light will illuminate
on the instrument cluster. If this occurs,
have the vehicle inspected by an
authorized retailer of Genesis Branded
products.
Safe Exit Assist disabled
OTM070098N
When the rear bumper around the rear
corner radar or sensor is covered with
foreign material, such as snow or rain,
or installing a trailer or carrier, it can
reduce the detecting performance and
temporarily limit or disable Safe Exit
Assist.
If this occurs, the ‘Blind-Spot Safety
system disabled. Radar blocked’ warning
message will appear on the instrument
cluster.
Safe Exit Assist will operate properly
when such foreign material or trailer,
etc., is removed, and then the engine is
restarted.
If Safe Exit Assist does not operate
properly after it is removed, have the
vehicle inspected by an authorized
retailer of Genesis Branded products.

7-74
Driver Assistance System
Blind-Spot View Monitor
2SHUDWLQJFRQGLWLRQV
When the left or right side turn signal
turns on, the image in that direction is
displayed on the instrument cluster.
Off conditions

[When the turn signal turns off, the
image on the instrument cluster will
turn off.

[When the hazard warning flasher
is on, Blind-Spot View Monitor will
turn off, regardless of the turn signal
status.

[When other important warning is
displayed on the instrument cluster,
Blind-Spot View Monitor may turn off.
%OLQG6SRW9LHZ0RQLWRU
0DOIXQFWLRQ
When Blind-Spot View Monitor is not
working properly, or the cluster display
flickers, or the camera image does
not display properly, have the vehicle
inspected by an authorized retailer of
Genesis Brand products.
:$51,1*

[7KHLPDJHVKRZQRQWKHFOXVWHUPD\
differ from the actual distance of the
REMHFW0DNHVXUHWRGLUHFWO\FKHFN
WKHYHKLFOH
VVXUURXQGLQJVIRUVDIHW\

[$OZD\VNHHSWKHFDPHUDOHQVFOHDQ
,IWKHOHQVLVFRYHUHGZLWKIRUHLJQ
PDWHULDOLWPD\DGYHUVHO\DIIHFW
FDPHUDSHUIRUPDQFHDQG%OLQG
6SRW9LHZ0RQLWRUPD\QRWRSHUDWH
SURSHUO\

7-88
Driver Assistance System
Limitations of Smart Cruise Control
Smart Cruise Control may not operate
properly, or it may operate unexpectedly
under the following circumstances:

[The detecting sensor or the
surroundings are contaminated or
damaged

[Washer fluid is continuously sprayed,
or the wiper is on

[The camera lens is contaminated due
to tinted, filmed or coated windshield,
damaged glass, or sticky foreign
material (sticker, bug, etc.) on the
glass

[Moisture is not removed or frozen on
the windshield

[The field of view of the front view
camera is obstructed by sun glare

[Street light or light from an oncoming
vehicle is reflected on the wet road
surface, such as a puddle on the road

[The temperature around the front
view camera is high or low

[An object is placed on the dashboard

[The surrounding is very bright

[The surrounding is very dark, such as
in a tunnel, etc.

[The brightness changes suddenly, for
example when entering or exiting a
tunnel

[The brightness outside is low, and the
headlamps are not on or are not bright

[Driving in heavy rain or snow, or thick
fog

[Driving through steam, smoke or
shadow
[Only part of the vehicle is detected

[The vehicle in front has no tail lights,
tail lights are located unusually, etc.

[The brightness outside is low, and the
tail lamps are not on or are not bright

[The rear of the front vehicle is small
or does not look normal (for example,
tilted, overturned, etc.)

[The front vehicle’s ground clearance is
low or high

[A vehicle suddenly cuts in front

[Your vehicle is being towed

[Driving through a tunnel or iron bridge

[Driving near areas containing metal
substances, such as a construction
zone, railroad, etc.

[An object reflecting off the front radar
such as a guardrail, nearby vehicle,
etc.

[The bumper around the front radar is
impacted, damaged or the front radar
is out of position

[The temperature around the front
radar is high or low

[Driving in vast areas where there
are few vehicles or structures (for
example, desert, meadow, suburb,
etc.)

[The vehicle in front is made of
material that does not reflect on the
front radar

[Driving near a highway interchange or
tollgate

[Driving on a slippery surface due to
snow, water puddle, ice, etc.

[Driving on a curved road

[The vehicle in front is detected late

[The vehicle in front is suddenly
blocked by an obstacle

[The vehicle in front suddenly changes
lane or suddenly reduces speed

7-89
07

[The vehicle in front is bent out of
shape

[The front vehicle’s speed is fast or
slow

[With a vehicle in front, your vehicle
changes lane at low speed

[The vehicle in front is covered with
snow

[Unstable driving

[You are on a roundabout and the
vehicle in front is not detected

[You are continuously driving in a circle

[Driving in a parking lot

[Driving through a construction area,
unpaved road, partial paved road,
uneven road, speed bumps, etc.

[Driving on an incline road, curved
road, etc.

[Driving through a roadside with trees
or streetlights

[The adverse road conditions cause
excessive vehicle vibrations while
driving

[Your vehicle height is low or high
due to heavy loads, abnormal tire
pressure, etc.

[Driving through a narrow road where
trees or grass are overgrown

[There is interference by
electromagnetic waves, such as
driving in an area with strong radio
waves or electrical noise

[Rear wheel steering system (if
equipped) is disabled
[Driving on a curved road
ORS071061
On curves, Smart Cruise Control may
not detect a vehicle in the same lane,
and may accelerate to the set speed.
Also, vehicle speed may rapidly
decrease when the vehicle ahead is
detected suddenly.
Select the appropriate set speed on
curves and apply the brake pedal or
accelerator pedal according to the
road and driving conditions ahead.
ORS071064
Your vehicle speed can be reduced
due to a vehicle in the adjacent lane.
Apply the accelerator pedal and select
the appropriate set speed. Check
to be sure that the road conditions
permit safe operation of Smart Cruise
Control.

7-91
07

[Situations when detecting are limited
ORS071046
ORS071047
In the following cases, some vehicles,
pedestrians or animals in your lane
cannot be detected by the sensor:
- Vehicles offset to one side
- Slow-moving vehicles or sudden-
decelerating vehicles
- Vehicles with higher ground
clearance or vehicles carrying loads
that stick out of the back of the
vehicle
- Vehicles that has the front lifted
dueto heavy loads
- Vehicles within approximately 6 ft.
(2m) from your vehicle
- Oncoming vehicles
- Stopped vehicles - Vehicles with small rear profile, such
as trailers
- Narrow vehicles, such as
motorcycles or bicycles
- Special vehicles
- Animals and pedestrians
Adjust your vehicle speed by
depressing the brake pedal according
to the road and driving conditions
ahead.
In the following cases, the vehicle
in front cannot be detected by the
sensor:
- You are steering your vehicle
- Driving on narrow or sharply curved
roads

7-109
07
ORS071076
Driving to one side within lane
When vehicle speed is above 40 mph (60
km/h), if a detected vehicle around you is
driving at a close distance, your vehicle
will control steering in the opposite
direction of the vehicle to assist in safe
driving. If there a detected vehicle in
both sides of the lane that are driving
close to you, the function will not veer to
the opposite side of the lane.
+LJKZD\'ULYLQJ$VVLVWVWDQGE\
When Smart Cruise Control is
temporarily canceled while Highway
Driving Assist is operating, Highway
Driving Assist will be in the standby state.
At this time, Lane Following Assist will
operate properly.
Information

['ULYLQJ6SHHG/LPLWKHOSV\RXGULYH
EHORZPSKNPK$WWKLVWLPH
the vehicle decelerates due to the
vehicle ahead. After the vehicle has
decelerated, it cannot automatically
accelerate.

['ULYLQJ6SHHG/LPLWZLOOFDQFHOLQWKH
following circumstances:
-When the driver grabs the steering
wheel again
-When the driver turns on Lane
)ROORZLQJ$VVLVWE\SUHVVLQJWKH/DQH
Driving Assist button
-When +, -,
switch or button is
RSHUDWHGRUWKHDFFHOHUDWRUSHGDORU
WKHEUDNHSHGDOLVGHSUHVVHG
Highway Lane Change Assist
'LVSOD\LQJRSHUDWLQJVWDWXV
You can see the status of the Highway Lane
Change Assist operation in the Driving
Assist view on the cluster. Refer to “View
Modes” section in chapter 4.
Highway Lane Change Assist function
will be displayed as below depending on
the status of the function.

7-111
07
Information

[While Lane Change Assist functionis
turned on (indicator on), Lane
Following Assist will not cancel even
if the turn signal indicator or hazard
ZDUQLQJIODVKHULVRSHUDWLQJ

[Lane Change Assist function turn
off automatically when driven in the
following road conditions:
-One driving lane
-A road with a intersection
orcrosswalk ahead
-A road with no structure, such as a
PHGLXPVWULSJXDUGUDLOVHWF
-7KHUHLVDSHGHVWULDQRUF\FOLVWRQWKH
road ahead

[When the function is in the ready state,
DQGYHKLFOHVSHHGLVEHORZPSK
NPKWKHIXQFWLRQZLOOFKDQJHWRWKH
standby state.
:$51,1*
:KHQ+LJKZD\/DQH&KDQJH$VVLVW
IXQFWLRQWXUQVRIIZKLOHRSHUDWLQJ
VWHHULQJDVVLVWZLOOEHWHPSRUDULO\
FDQFHOHG$OZD\VEHFDXWLRXVZKLOH
GULYLQJ
+LJKZD\/DQH&KDQJH$VVLVWRSHUDWLQJ
ORS071269
M: Center
Highway Lane Change Assist function
will operate, when you push the turn
signal lever up or down to the A or B
position while the function is in the ready
state (indicator is green), and all of the
following conditions are satisfied:

[The driver has his/her hand on the
steering wheel

[There is no collision risk in the
direction of lane change

[There is a single dotted lane line in the
direction of lane change

[There are no Forward Collision-
Avoidance Assist and Blind Spot
Collision-Avoidance Assist warnings

[The vehicle is driven in the middle of
the lane (should not be driving close
to one side of the lane)

[The road you are driving on, or the
road you are about to change lane is a
road that the function can operate

7-118
Driver Assistance System
6XUURXQG9LHZ0RQLWRU
Operation
ORS071018
ORS072246N
Press the Parking/View button M to turn
on Surround View Monitor.
Press the button again to turn off the
function.
Front View
The front image is displayed on the
screen when the gear is in N (Neutral) or
D (Drive) to assist in parking. Using the
view button N you may select top view,
front view, side view and 3D view.
)URQW9LHZZKLOHSDUNLQJ
The front view while parking function will
turn on under the following conditions:

[The gear is in N (Neutral) or D (Drive),
and vehicle speed is 6 mph (10 km/h)
or less.

[The Parking/View button M is pressed,
while the gear is in N (Neutral) or D
(Drive), and vehicle speed is 6 mph (10
km/h) or less.

[Surround View Monitor Auto On
function will operate when the
following conditions are satisfied:
-:LWKC'ULYHU$VVLVWDQFH

7-119
07
Rear view
The rear image is displayed on the screen
when the gear is in P (Park) to assist in
parking. Using the view button N you
may select top view, front view, side view
and 3D view.
5HDU9LHZZKLOHSDUNLQJ
The rear view while parking function will
turn on under the following conditions:

[The Parking/View button M is
pressed, while the gear is in P (Park),
N (Neutral) or D( Drive), and vehicle
speed is 6 mph (10 km/h) or less.

[The gear is shifted to R (Reverse)

[The gear is shifted from R (Reverse) to
N (Neutral) or D (Drive)
When the gear is in P (Park), N (Neutral)
or D (Drive), the rear view function will
turn off under the following conditions:

[The gear is shifted to P (Park).

[The Parking/View button M or the
infotainment system button O is
pressed.

[The Home button P is pressed.

[The vehicle speed is above 6 mph (10
km/h).
When the gear is in R (Reverse), the rear
view function will turn off under the
following conditions:

[The gear is shifted to P (Park)
Information

[When the rear view turn on while the
JHDULVLQ33DUN11HXWUDORU'
'ULYHWKHSUHYLRXVYLHZPRGHZLOOEH
GLVSOD\HG

[When the gear is in R (Reverse), the
rear view does not turn off.
3D view
The 3D view shows the image around the
vehicle from various angles.
You can change angles by tapping the
screen. Press the 3D View button again
to return to the initial angle.
3D view will turn on when the 3D view
is selected among the view buttons N
under the following conditions:

[The gear is in P (Park), N (Neutral) or D
(Drive) when vehicle speed is below 6
mph (10 km/h).

[The Surround View Monitor is turned
on when the gear is in R (Reverse).
When the gear is in P (Park), N (Neutral)
or D (Drive), 3D view will turn off under
the following conditions:

[The gear is shifted to P (Park).

[The Parking/View button M is pressed.

[The infotainment system button O is
pressed.

[The Home button P is pressed.

[Vehicle speed is above 6 mph (10
km/h).
Information
'YLHZGRHVQRWGLVSOD\JXLGHOLQHV

7-120
Driver Assistance System
6XUURXQG9LHZ0RQLWRU
0DOIXQFWLRQDQG/LPLWDWLRQV
Surround View Monitor malfunction
When Surround View Monitor is not
working properly, or the screen flickers,
or the camera image does not display
properly, have the vehicle inspected by
an authorized retailer of Genesis Branded
products.
Limitations of Surround View
Monitor

[When the vehicle is stopped for a long
time in winter or when the vehicle is
parked in an indoor parking lot, the
exhaust fumes may temporarily blur
the image.

[The screen may be displayed
abnormally, and an icon will appear at
the top left side of the screen under
the following circumstances:
- The trunk is opened
- The driver or front passenger door
is opened
- The side view mirror is folded
:$51,1*

[$/:$<6ORRNDURXQG\RXUYHKLFOH
WRPDNHVXUHWKHUHDUHQRREMHFWV
RUREVWDFOHVEHIRUHPRYLQJWKH
YHKLFOH:KDW\RXVHHRQWKHVFUHHQ
PD\GLIIHUIURPWKHDFWXDOYHKLFOH
TV
ORFDWLRQ

[7KHLPDJHVKRZQRQWKHVFUHHQPD\
differ from the actual distance of the
REMHFW0DNHVXUHWRGLUHFWO\FKHFN
WKHYHKLFOH
VVXUURXQGLQJVIRUVDIHW\

[6XUURXQG9LHZ0RQLWRULVGHVLJQHG
WREHXVHGRQDIODWVXUIDFH
7KHUHIRUHLIXVHGRQURDGVZLWK
GLIIHUHQWKHLJKWVVXFKDVFXUEV
DQGVSHHGEXPSVWKHLPDJHLQWKH
VFUHHQP\QRWORRNFRUUHFW

[$OZD\VNHHSWKHFDPHUDOHQVFOHDQ
,IWKHOHQVLVFRYHUHGZLWKIRUHLJQ
PDWHULDOLWPD\DGYHUVHO\DIIHFW
camera performance and Surround
9LHZ0RQLWRUPD\QRWRSHUDWH
SURSHUO\+RZHYHUGRQRWXVH
FKHPLFDOVROYHQWVVXFKDVVWURQJ
detergents containing high alkaline
RUYRODWLOHRUJDQLFVROYHQWVJDVROLQH
DFHWRQHHWF7KLVPD\GDPDJHWKH
FDPHUDOHQV