trailer GENESIS G90 2023 User Guide
Page 480 of 676
7-91
07
[ Situations when detecting are limited
ORS071046
ORS071047
In the following cases, some vehicles,
pedestrians or animals in your lane
cannot be detected by the sensor:
- Vehicles offset to one side
- Slow-moving vehicles or sudden-
decelerating vehicles
- Vehicles with higher ground
clearance or vehicles carrying loads
that stick out of the back of the
vehicle
- Vehicles that has the front lifted
dueto heavy loads
- Vehicles within approximately 6 ft.
(2m) from your vehicle
- Oncoming vehicles
- Stopped vehicles - Vehicles with small rear profile, such
as trailers
- Narrow vehicles, such as
motorcycles or bicycles
- Special vehicles
- Animals and pedestrians
Adjust your vehicle speed by
depressing the brake pedal according
to the road and driving conditions
ahead.
In the following cases, the vehicle
in front cannot be detected by the
sensor:
- You are steering your vehicle
- Driving on narrow or sharply curved
roads
Page 517 of 676
7-128
Driver Assistance System
OJWEV071275L
When the side view mirror warning
light is not working properly, the ‘Check
side view mirror warning light’ warning
message will appear on the instrument
cluster for several seconds, and the
master (
) warning light will illuminate
on the instrument cluster. If this occurs,
have the vehicle inspected by an
authorized retailer of Genesis Branded
products.
Rear Cross-Traffic Collision-
Avoidance Assist disabled
ORS071287L
When the rear bumper around the rear-
side radar or sensor is covered with
foreign material, such as snow or rain,
or installing a trailer or carrier, it can
reduce the detecting performance and
temporarily limit or disable Rear Cross-
Traffic Collision-Avoidance Assist.
If this occurs, the ‘Rear Cross-Traffic
Collision-Avoidance Assist disabled.
Radar blocked’ warning message will
appear on the instrument cluster.
Rear Cross-Traffic Collision-Avoidance
Assist will operate properly when
such foreign material or trailer, etc., is
removed.
If Rear Cross-Traffic Collision-Avoidance
Assist does not operate properly after it
is removed, have the vehicle inspected
by an authorized retailer of Genesis
Branded products.
: $ 5 1 , 1 *
[ ( Y H Q W K R X J K W K H Z D U Q L Q J P H V V D J H
G R H V Q R W D S S H D U R Q W K H F O X V W H U 5 H D U
& U R V V 7 U D I I L F & R O O L V L R Q $ Y R L G D Q F H
$ V V L V W P D \ Q R W R S H U D W H S U R S H U O \
[ Rear Cross-Traffic Collision-
$ Y R L G D Q F H $ V V L V W P D \ Q R W R S H U D W H
S U R S H U O \ L Q D Q D U H D I R U H [ D P S O H
R S H Q W H U U D L Q Z K H U H D Q \ V X E V W D Q F H
are not detected after turning ON the
H Q J L Q H
Page 527 of 676
7-138
Driver Assistance System
Parking Distance Warning disabled
OJWEV071233L
If this occurs the ‘Parking Distance
Warning system limited. Ultrasonic
sensor blocked’ warning message
appears on the instrument cluster.
Parking Distance Warning will operate
properly when snow, rain or foreign
material is removed. If Parking Distance
Warning does not operate properly
after obstruction (snow, rain, or foreign
material) is removed (including trailer,
carrier, etc., from the rear bumper), have
the vehicle inspected by an authorized
retailer of Genesis Branded products.
Limitations of Parking Distance
Warning
[ Parking Distance Warning may not
operate properly when:
- There is excessive moisture or frost
on the sensor
- Sensor is covered with foreign
substance, such as snow or water
(Parking Distance Warning will
operate properly when such
substance is removed.)
- The weather is extremely hot or cold
- The sensor or sensor assembly is
disassembled
- The surface of the sensor is pressed
hard or hit with a hard object
- The surface of the sensor is
scratched with a sharp object
- The sensors or its surrounding
area is directly sprayed with high
pressure washer
[ Parking Distance Warning may
malfunction when:
- Heavy rain or water spray is present
- Water flows on the surface of the
sensor
- Affected by another vehicle’s
sensors
- The sensor is covered with snow or
ice
- Driving on uneven road, gravel
roads or bushes
- Objects that generates ultrasonic
waves are near the sensor
- License plate is installed in a
different spot from the original
location
- The vehicle bumper height or
ultrasonic sensor installation has
been modified
- Attaching equipment or accessories
next to the ultrasonic sensors
Page 531 of 676
7-142
Driver Assistance System
3 D U N L Q J & R O O L V L R Q $ Y R L G D Q F H
Assist Operation
Operating conditions
Select ‘Rear Safety’ from the ‘Parking
Safety’ menu of the infotainment system.
Parking Collision-Avoidance Assist is
enabled when the following conditions
are satisfied:
Rear Safety
[ The trunk and door are closed
[ The Electronic Parking Brake (EPB) is
released
[ A trailer is not connected
[ The gear is shifted to R (Reverse)
[ Vehicle speed is below 6 mph (10
km/h) (detecting pedestrians)
[ Vehicle speed is below 2 mph (4 km/h)
(detecting objects)
[ Parking Collision-Avoidance Assist
components such as the wide-rear
view camera and the rear ultrasonic
sensors are in normal conditions
) U R Q W 6 L G H 6 D I H W \
[ The trunk and door are closed
[ The Electronic Parking Brake (EPB) is
released
[ A trailer is not connected
[ The gear is shifted to R (Reverse) or D
(Drive)
[ Vehicle speed is below 2 mph (4 km/h)
(for pedestrians, objects)
[ Parking Collision-Avoidance Assist
components such as the wide-rear
view camera and the rear ultrasonic
sensors are in normal conditionsWhen Parking Collision-Avoidance Assist
activates, a line appears behind the
vehicle image in the instrument cluster.
[ Rear Safety: Behind the vehicle image
[ Front/Side Safety: In front of vehicle
image
ORS071131
Information
3 D U N L Q J & R O O L V L R Q $ Y R L G D Q F H $ V V L V W
R S H U D W H V R Q O \ R Q F H D I W H U V K L I W L Q J W K H J H D U
to R (Reverse) or D (Drive). To reactivate
3 D U N L Q J & R O O L V L R Q $ Y R L G D Q F H $ V V L V W V K L I W
the gear from another gear to R (Reverse)
or D (Drive).
Page 555 of 676
7-166
Driver Assistance System
Smart Exit
2 S H U D W L Q J R U G H U
Smart Exit function operates in the
following order:
1. Getting ready for exit
2. Checking space
3. Select exit direction
4. Smart Exit
* H W W L Q J U H D G \ I R U H [ L W
ORS071142
(1) With the engine turned on,
depress the brake pedal and shift
the gear to P (Park) or N (Neutral).
(2) Press and hold the Parking/View
(
) button to turn on Remote
Smart Parking Assist.
Information
[ 'Agree' must be selected on the
infotainment system screen and the
L Q I R W D L Q P H Q W V \ V W H P K D V W R R S H U D W H
S U R S H U O \ W R X V H 6 P D U W 6 P D U W ( [ L W
function.
[ ' U L Y H E H O R Z P S K N P K Z L W K
the engine on and shift the gear to N
(Neutral), Smart Exit function can be
used.
[ If the function is turned on again
D I W H U S D U D O O H O S D U N L Q J L V F R P S O H W H G E \
5 H P R W H 6 P D U W 3 D U N L Q J $ V V L V W 6 P D U W
Exit function can be used.
& K H F N L Q J V S D F H
ORS071279L
(1) When the vehicle is stopped by
depressing the brake pedal, the
vehicle sensors will detect the
distance from nearby objects and
check for space to exit.
(2) When checking for space is
complete, a message will appear
on the infotainment system screen
with an audible sound to notify the
search is complete.
: $ 5 1 , 1 *
[ : K L O H F K H F N L Q J I R U V S D F H L I W K H U H L V
D U L V N R I F R O O L V L R Q Z L W K S H G H V W U L D Q
D Q L P D O R U R E M H F W L Q W K H G L U H F W L R Q R I
Y H K L F O H H [ L W I R U \ R X U V D I H W \ 6 P D U W
( [ L W I X Q F W L R Q F D Q E H W X U Q H G R I I
[ ( Y H Q L I F K H F N I R U V S D F H L V F R P S O H W H G
R E M H F W V L Q W K H E O L Q G V S R W D U H D F D Q Q R W
E H G H W H F W H G E \ W K H V H Q V R U V 7 K H
G U L Y H U P X V W G L U H F W O \ F K H F N W K H E O L Q G
spot area and continue using the
I X Q F W L R Q
Information
' X H W R D E Q R U P D O S H U I R U P D Q F H R I W K H
ultrasonic sensor or the influence of the
V X U U R X Q G L Q J V 3 D U N L Q J I X Q F W L R Q P D \ Q R W
E H D E O H W R V H D U F K I R U D Q H [ L W V S D F H H Y H Q L I
W K H U H L V D D Q H [ L W V S D F H R U P D \ V H D U F K I R U
D V S D F H W K D W L V Q R W V X L W D E O H I R U H [ L W L Q J
- 7 K H S D U N H G Y H K L F O H K D V R E M H F W V D W W D F K H G
W R W K H E X P S H U V X F K D V E X P S H U J X D U G
trailer hitch, etc.
Page 560 of 676
7-171
07
OJWEV071288L
5 H P R W H 6 P D U W 3 D U N L Q J $ V V L V W V W D Q G E \
‘Parking Assist Conditions Not Met’
message appears when Parking/View
(
) button has been pressed and held
while Remote Smart Parking Assist is in
standby.
After a while, press and hold the
Parking/View (
) button again to see if
Remote Smart Parking Assist works.
The message appears even when the
smart key's battery is low. Check the
smart key battery level.
Limitations of Remote Smart Parking
Assist
In the following circumstances, Remote
Smart Parking Assist performance to
park or exit the vehicle may be limited,
there may be a risk of collision, or
Remote Smart Parking Assist may turn
off. Park or exit the vehicle manually if
necessary.
[ An object is attached to the steering
wheel
[ The vehicle is installed with a snow
chain, spare tire or different size
wheel
[ Tire pressure is lower or higher than
the standard tire pressure
[ Your vehicle is loaded with cargo
longer or wider than your vehicle or a
trailer is connected to your vehicle [ There is a problem with the wheel
alignment
[ Your vehicle is leaned severely to one
side
[ Your vehicle is equipped with a trailer
hitch
[ The license plate is installed
differently from the original location
[ There is a person, animal or object
above or below the ultrasonic sensor
when Remote Smart Parking Assist is
activated
[ The parking space is narrow or curve
[ There is an obstacle such as a person,
animal or object (trash can, bicycle,
motorcycle, shopping cart, narrow
pillar, etc.) near the parking space
[ There is a circular pillar or narrow
pillar, or a pillar surrounded by objects
such as fire extinguisher, etc., near the
parking space
[ The road surface is bumpy (curbstone,
speed bump, etc.)
[ The road is slippery
[ The parking space is near a vehicle
with higher ground clearance or big,
such as a truck, etc.
[ The parking space is Inclined
Page 585 of 676
8-18
Emergency Situations
When driving with the compact spare tire
mounted to your vehicle:
• Check the tire pressure after installing
the compact spare tire. The compact
spare tire should be inflated to 60 psi
(420 kPa).
• Do not take this vehicle through
an automatic car wash while the
compact spare tire is installed.
• Do not use the compact spare tire on
any other vehicle because this tire
has been designed especially for your
vehicle.
• The compact spare tire’s tread life is
shorter than a regular tire. Inspect
your compact spare tire regularly and
replace worn compact spare tires with
the same size and design, mounted on
the same wheel.
• Do not use more than one compact
spare tire at a time.
• Do not tow a trailer while the compact
spare tire is installed.
Information
When the original tire and wheel are
repaired and reinstalled on the vehicle, the
wheel bolt torque must be set correctly.
The correct wheel bolt tightening torque is
101~116 lbf·ft (14~16 kgf·m).
NOTICE
To prevent damaging the compact
spare tire and your vehicle:
• Drive slowly enough for the road
conditions to avoid all hazards, such
as a potholes or debris.
• Avoid driving over obstacles. The
compact spare tire diameter is
smaller than the diameter of a
conventional tire and reduces the
ground clearance approximately
1 in. (25 mm).
• Do not use tire chains on the
compact spare tire. Because of the
smaller size, a tire chain will not fit
properly.
• Do not use the compact spare tire
on any other wheels, nor should
standard tires, snow tires, wheel
covers or trim rings be used with the
compact spare wheel.
• Do not suddenly accelerate or
decelerate 0 ~ 25 mph (0 ~ 40 km/h)
in any driving mode. It may cause
leakage of transfer oil.
008_RS4_HMA.indd 8-182022-04-18 3:48:10
Page 587 of 676
8-20
Emergency Situations
ORS081006ORS081006
For safe operation, carefully read and
follow the instructions in this manual
before use.
M Compressor
N Sealant bottle
The Tire Mobility Kit is a temporary fix to
the tire and the tire should be inspected
by an authorized retailer of Genesis
Branded products or the equivalent
approved for your vehicle as soon as
possible.
CAUTION
When two or more tires are flat, do not
use the tire mobility kit because the
sealant provided with the Tire Mobility
Kit must be used for only one flat tire.
WARNING
Do not use the Tire Mobility Kit to repair
punctures in the tire walls. This can
result in an accident due to tire failure.
WARNING
Have your tire repaired as soon as
possible. The tire may lose air pressure
at any time after inflating with the Tire
Mobility Kit.
Introduction
With the Tire Mobility Kit you stay mobile
even after experiencing a tire puncture.
The compressor and sealing compound
system effectively and comfortably seals
most punctures in a passenger vehicle
tire caused by nails or similar objects and
reinflates the tire.
After you ensure that the tire is properly
sealed you can drive cautiously on the
tire (distance up to 120 miles (200 km))
at a max. speed of 50 mph (80 km/h) in
order to reach a service station or tire
dealer for the tire replacement.
It is possible that some tires, especially
with larger punctures or damage to the
sidewall, cannot be sealed completely.
Air pressure loss in the tire may adversely
affect tire performance.
For this reason, you should avoid abrupt
steering or other driving maneuvers,
especially if the vehicle is heavily loaded
or if a trailer is in use.
The Tire Mobility Kit is not designed
or intended as a permanent tire repair
method and is to be used for one tire
only.
This instruction shows you step by step
how to temporarily seal the puncture
simply and reliably.
Read the section “Notes on the safe use
of the Tire Mobility Kit”.
WARNING
Do not use the TMK if a tire is severely
damaged by driving run flat or with
insufficient air pressure.
Only punctured areas located within the
tread region of the tire can be sealed
using the TMK.
IF YOU HAVE A FLAT TIRE íWITH TIRE MOBILITY KIT, IF
EQUIPPEDî
008_RS4_HMA.indd 8-202022-04-18 3:48:11