light GENESIS G90 2023 Repair Manual

5-65
05
3) Two-Way Communication
3URJUDPPLQJ)RUVHOHFWJDUDJHGRRU
openers)
If your garage door opener has the
‘myQ’ logo on its side, your opener
likely has Two-Way Communication
capability. HomeLink has the capability
to establish Two-Way Communication
with your garage door opener. HomeLink
can receive and display “closing”
or “opening” status messages from
compatible garage door openers. At
any time, Home-Link can also recall
and display the last recorded status
communicated by the garage door
opener to indicate your garage door
being “closed” or “opened”.
To check if your garage door opener is
compatible with this feature, refer to
www.homelink.com/compatible/Two-
way-Communication. If your garage
door opener has this functionality, AND
the Two-Way Communication indicators
P, R in the mirror appear while the
garage door is opening/closing, then
no further steps are needed. Two-Way
Communication Programming is already
complete. However, if your garage door
opener has this functionality, AND the
Two-Way Communication indicators P,
R in the mirror DO NOT appear while
the garage door is opening/closing, use
the following instructions to enable this
functionality.
1. In your vehicle, press and hold the
programmed HomeLink button for 2
seconds, then release. Confirm that
the garage door is moving. AFTER it
stops, you will have one minute to
complete the following steps:
ÃA ladder and/or second person may
simplify the following steps.2. On your garage door opener in your
garage, locate the “Learn” button
(usually near where the hanging
antenna wire is attached to the garage
door opener). If there is difficulty
locating this button, reference the
device’s owner’s manual.
3. Press and release the “Learn” button.
4. A light on your garage door opener
may flash, and your Two-Way
Communication indicators P, R in
your vehicle may flash, confirming
completion of the process.
5. Return to the vehicle and firmly
press and release the programmed
HomeLink button to activate
your garage door. The Two-Way
Communication indicators P, R flash
in orange when the door is moving.
Do not make any additional button
presses until AFTER the garage door
has come to a complete stop.
6. Your Two-Way Communication
programming is now complete.
Information
If your garage door opener has Two-
:D\&RPPXQLFDWLRQIXQFWLRQDOLW\
it is possible for HomeLink to stop
functioning the garage door shortly
after initial programming, IF the Two-
:D\&RPPXQLFDWLRQ3URJUDPPLQJ
wasn’t properly completed. This
usually happens after the first 10 times
a programmed HomeLink button is
pressed. If you experience this, completing
the “Programming a New HomeLink
%XWWRQ

5-66
Convenience Features
4) Canadian Programming
Canadian radio-frequency laws require
transmitter remote signals to “time-
out” (or quit) after a couple seconds of
transmission, which may not be long
enough for HomeLink to pick up the signal
during programming.
If you live in Canada or you are having
difficulties programming a gate operator
or garage door opener by using the
programming procedures, replace
“Programming a New HomeLink Button”
step 3 with the following:
While the HomeLink indicator light S is
flashing orange, press and release (“cycle”)
your device’s handheld remote every two
seconds until the HomeLink indicator light
S changes from orange to green. You may
now release the hand-held remote button.
Then proceed with “Programming a New
HomeLink Button” step 4.2SHUDWLQJ+RPH/LQN®
 2SHUDWLQJ+RPH/LQNp
ORS052307N
1. Press and release the desired
programmed HomeLink button (M, N
or O).
Information
The HomeLink indicator S should
light green, solid or flashing, and your
programmed device should operate.
If your device does not operate, the
HomeLink programming was not
successful, and you’ll need to reprogram
the button.

5-68
Convenience Features
3. Erasing HomeLink® Buttons
1) Erasing and Reprogramming a Single
+RPH/LQNp%XWWRQ
1. Press and hold the desired HomeLink
button you want to re-program. DO
NOT release the button.
2. The HomeLink indicator light S will
illuminate solid green. Release the
button as soon as the HomeLink
indicator light S begins to flash
orange, usually about 20 seconds.
3. Proceed with the steps in the
“Programming a New HomeLink
Button” section.
Information
If you do not complete the re-
programming of a new device to the
button, it will revert to the previously
stored programming.
2) The following instructions will erase
$//+RPH/LQNpSURJUDPPLQJIURP
ALL buttons:
ORS052310N
1. Press and hold the buttons M and O
simultaneously.
2. The HomeLink indicator light S will
illuminate solid Orange for about 10
seconds.
3. Release the buttons once the
HomeLink indicator light S changes
to Green and flashes rapidly.
4. Now all three HomeLink buttons
M, N and O are cleared of any
programming.
Information
HomeLink® and the HomeLink® House
logo are registered trademarks of Gentex
&RUSRUDWLRQ
The myQ logo is a registered trademark of
7KH&KDPEHUODLQ*URXS,QF

5-80
Convenience Features
If your vehicle is equipped with a
sunroof, you can slide or tilt your sunroof
with the sunroof switch located on the
overhead console.
ORS052049N
The sunroof can only be operated when
the Engine Start/Stop button is in the ON
or START position.
The sunroof can be operated for
approximately 3 minutes after the Engine
Start/Stop button is in the ACC or OFF
position. However, if the front door is
open, the sunroof cannot be operated
even within the 3minute period.
WARNING

[Adjust the sunroof or sunshade when
your vehicle stops. This could result
in loss of control and an accident
that may cause injury, or property
damage.

[Do not leave the engine running
and the key in your vehicle with
unsupervised children. Unattended
children could operate the sunroof,
which could result in serious injury.

[Do not sit on the top of the vehicle. It
may cause injury or vehicle damage.
NOTICE
Do not operate the sunroof when roof
bars are installed on the vehicle or
when there is luggage on the roof.
Power Sunshade
Use the power sunshade to block direct
sunlight coming through the sunroof
glass.
Using front seat power sunshade
ORS051050

[Push the sunroof switch rearward to
the first detent position, the power
sunshade automatically slides open.

[Push the sunroof switch forward to
the first detent position, the power
sunshade automatically closes.
However, if the sunroof glass is open,
the glass will close first.
To stop the power sunshade at any point,
push the sunroof switch in any direction.
3$125$0,&681522)

5-81
05
Using the rear seat power sunshade
(if equipped)
ORS052051N
2SHUDWLQJUHDUVHDWVXQVKDGHVZLWFK
Press the switch to open the rear seat
power sunshade. Press again to close the
sunshade.
The sunroof will not be opened.
ORS051249L
2SHUDWLQJUHDUVHDWVXQVKDGHIURP
touchscreen
: Stops the rear seat power
sunshade from opening or closing.
: Stops the seat mode and
the rear seat power sunshade from
operating.
1. Press
from the left side menu of
the armrest touchscreen.

[Sunshade adjusting screen is
displayed.
2. Press and slide
in the center of
the display upward or downward to
completely raise or lower the power
sunshade.

[To adjust the power sunshade to the
desired position when the sunshade
is opening or closing, press

on the upper right part of the
touchscreen or press
again.
CAUTION
Do not push or pull the power sunshade
with your hands. The sunshade may be
damaged and cause malfunction.
Information

[Wrinkles formed on the power
sunshade are normal due to material
characteristic.

[While the power sunshade is opened
or being operated, the mood lighting
turns off.

5-84
Convenience Features
Resetting the Sunroof
Front seat power sunshade and
glass
ORS052055N
In some circumstances resetting the
sunroof operation may need to be
performed. Some instances where
resetting the sunroof may be required
include:

[When the 12-volt battery is either
disconnected or discharged

[When the sunroof fuse is replaced

[If the sunroof one-touch AUTO OPEN/
CLOSE operation is not functioning
properlySunroof resetting procedure:
1. It is recommended to perform the
reset procedure with the vehicle
engine running. Start the vehicle in P
(Park).
2. Make sure the power sunshade and
sunroof glass are in the fully closed
position. If the power sunshade
and sunroof glass are open, push
the switch forward until the power
sunshade and sunroof glass are fully
closed.
3. Release the switch when the power
sunshade and sunroof glass are fully
closed.
4. Push the switch forward until the
power sunshade and sunroof glass
move slightly. Then release the switch.
5. Once again push and hold the sunroof
switch forward until the power
sunshade and sunroof glass slide
open and close.

[Do not release the switch until the
operation is completed.
If you release the switch during
operation, start the procedure again
from step 2.
Information
If the sunroof is not reset when the vehicle
battery is disconnected or discharged, or
the sunroof fuse is blown, the sunroof may
not operate normally.

5-85
05
Rear Seat Power Sunshade
ORS052051N
Reset the rear seat power sunshade in
the following situations.

[When the 12-volt battery is either
disconnected or discharged.

[When the rear seat power sunshade is
not working properly.
1. It is recommended to perform the
reset procedure with the vehicle
engine running. Start the vehicle in P
(Park).
2. Press and hold the switch until the
rear seat power sunshade is fully
closed.
3. Hold the switch until the rear seat
power sunshade slightly moves.
Release the switch until the sunshade
moves slightly.
4. Press and hold the switch again until
the power sunshade is opened then
closed.

[Do not release the switch until
the rear seat sunshade completes
opening/closing. If you release the
switch during operation, start the
procedure again from step 2.
CAUTION
The rear seat power sunshade may not
work properly if it is not reset.
Sunroof Open Warning
ORS041022
If the driver turns off the engine when
the sunroof is not fully closed, the
warning chime will sound for several
seconds and the sunroof open warning
will appear on the cluster LCD display.
Close the sunroof securely when leaving
your vehicle.
CAUTION
Make sure the sunroof is closed fully
when leaving your vehicle. If the
sunroof is left open, rain or snow may
wet the interior of the vehicle. Also,
leaving the sunroof open when the
vehicle is unattended may invite theft.

5-86
Convenience Features
Opening the Hood
ORS051056
1. Park the vehicle and set the parking
brake.
2. Pull the release lever to unlatch the
hood. The hood should pop open
slightly.
ORS051057
3. Go to the front of the vehicle, raise the
hood slightly, push up the secondary
latch M inside of the hood center and
lift the hood N.
After the hood has been lifted halfway,
it will raise completely by itself.
Closing the Hood
1. Before closing the hood, check in and
around the engine compartment to
ensure the following:
- Any tools or other loose objects
are removed from the engine
compartment area or hood
opening area
- All glove, rags, or other
combustible material is removed
from the engine compartment
- All filler caps are tightly and
correctly installed
2. Lower the hood halfway (lifted
approximately 12 in. (30 cm) from the
closed position) and push down to
securely lock in place. Then double
check to be sure the hood is secure.
If the hood can be raised slightly, it is
not securely locked. Open it again and
close it with more force.
WARNING

[Before closing the hood, ensure
all obstructions are removed from
around the hood opening.

[Always double check to be sure that
the hood is firmly latched before
driving away. Check there is no
hood open warning light or message
displayed on the instrument cluster.
Driving with the hood opened may
cause a total loss of visibility, which
might result in an accident.

[Do not move the vehicle with the
hood in the raised position, as vision
is obstructed, which might result in
an accident, and the hood could fall
or be damaged.
HOOD

5-88
Convenience Features
Information

[In cold and wet climates, the outside
power trunk open button may not work
properly due to freezing conditions. If
this occurs, remove the ice before using
the outside power trunk open/close
button or use the power trunk open/
close button on the smart key or the
instrument panel.

[If you leave the smart key in the trunk
and close the trunk, a warning will
sound for about 5 seconds. If this
occurs, open the trunk by pressing the
power trunk open button on the outside
of the trunk.

[If there are obstacles such as snow
on the trunk, the trunk may not open
automatically. After removing the
obstacle, try to open it again.

[Be careful where there is an incline, as
the trunk lid may drop slightly when it
is stopped before it fully opens.
Operating the Power Trunk
Power trunk open button (Smart
key)
ORS051059
When the trunk is closed, press the
power trunk open button for 1 second.
The trunk will open with a warning
sound.
While the trunk is opening, press the
button to stop power trunk operation.

5-95
05
Deactivating smart trunk
ORS051070
M Door lock
N Door unlock
O Trunk open/close
P Panic
If you press any button on the smart key
during the Detect and Alert stage, the
smart trunk function will be deactivated.
Make sure to be aware of how to
deactivate the smart trunk function for
emergency situations.
Information

[If you press the door unlock button
N, the smart trunk function will be
deactivated temporarily. But, if you do
not open any door for 30 seconds, the
smart trunk function will be activated
again.

[If you press the trunk open button
O for more than 1 second, the trunk
opens.

[The smart trunk function will still be
activated if you press the door lock
button M or trunk open button O on
the smart key as long as the smart
trunk is not already in the Detect and
Alert stage.

[In case you have deactivated the smart
trunk function by pressing the smart
key button and opened a door, the
smart trunk function can be activated
again by closing and locking all doors.
Detecting Area
ORS051071L

[The smart trunk detecting area
extends approximately 20-40 in. (50-
100 cm) behind the vehicle. If you are
positioned in the detecting area and
are carrying the smart key, the hazard
warning lights will blink and the chime
will sound for about 3 seconds to alert
you that the smart trunk will open.

[The alert stops once the smart key is
moved outside of the detecting area
within the 3 second period.
Information

[The smart trunk function may not
operate properly if any of the following
instances occur:
-The smart key is close to a radio
transmitter such as a radio station or
an airport which can interfere with
normal operation of the transmitter.
-The smart key is near a mobile two
way radio system or a cellular phone.
-Another vehicle’s smart key is being
operated close to your vehicle.

[The smart trunk detecting area may
change when:
-The vehicle is parked on an incline
-or slope.
-2QHVLGHRIWKHYHKLFOHLVUDLVHGRU
lowered relative to the opposite side.