light GENESIS G90 2023 Manual Online

5-115
05
ORS051272
High Beam Assist will automatically
switch between high beam and low
beam depending on the detected
brightness from the lamps of oncoming
vehicles or vehicles in front.
Detecting sensor
ORS071001L
M: Front view camera
The front view camera is used as a
detecting sensor to detect ambient light
and brightness while driving.
Refer to the picture above for the
detailed location of the detecting sensor.
NOTICE
Always keep the front view camera in
good condition to maintain optimal
performance of High Beam Assist.
)RUPRUHGHWDLOVRQWKHSUHFDXWLRQV
of the front view camera, refer to

U)RUZDUG&ROOLVLRQ$YRLGDQFH$VVLVW
)&$
VVHFWLRQLQFKDSWHU
High Beam Assist Setting
ORS051241L
With the Engine Start/Stop button in the
21SRVLWLRQVHOHFW
S/LJKWV

5-116
Convenience Features
High Beam Assist Operation
Display and control

[After selecting ‘High Beam Assist’
in the Settings menu, High Beam
Assist will operate by following the
procedure below.
- Place the headlight switch in
the AUTO position and push
the headlight lever towards the
instrument cluster. The High Beam
Assist (
) indicator light will
illuminate on the cluster and High
Beam Assist will be enabled.
- When High Beam Assist is enabled,
high beam will turn on when vehicle
speed is above 25 mph (40 km/h).
When vehicle speed is below 15
mph (25 km/h), high beam will turn
off.
- The High Beam (
) indicator light
will illuminate on the cluster when
high beam is on.

[When High Beam Assist is operating,
if the headlight lever or switch is used,
High Beam Assist operates as follow:
- If the headlight lever is pulled
towards you when the high beam
is off, the high beam will turn
on without High Beam Assist
cancelled. When you let go of the
headlight lever, the lever will move
to the middle and the high beam
will turn off.
- If the headlight lever is pulled
towards you when the high beam is
on by High Beam Assist, low beam
will turn on and High Beam Assist
will turn off.
- If the headlight switch is placed
from AUTO to another position
(headlight/position/off), High
Beam Assist will turn off and the
corresponding lamp will turn on.
[When High Beam Assist is operating,
high beam switches to low beam if
any of the following conditions occur:
- When the headlight of an oncoming
vehicle is detected.
- When the tail lamp of a vehicle in
front is detected.
- When the headlight or tail lamp of a
motorcycle or a bicycle is detected.
- When the surrounding ambient light
is bright enough that high beams
are not required.
- When streetlights or other lights are
detected.
Information
The images and colors in the instrument
may differ depending on the instrument
type or theme selected from the
instrument.

5-117
05
High Beam Assist Malfunction
and Limitations
High Beam Assist malfunction
OJWEV051094L
When High Beam Assist is not working
properly, the ‘Check High Beam Assist
system’ warning message will appear
and
warning light will illuminate on
the cluster. Have the vehicle inspected
by an authorized retailer of Genesis
Branded products.
Limitations of High Beam Assist

[Light from an oncoming or front
vehicle is not detected because of
lamp damage, or because it is hidden
from sight, etc.

[Headlight of an oncoming or front
vehicle is covered with dust, snow or
water.

[An oncoming or front vehicle’s
headlights are off, but the fog lamps
are on, etc.

[There is a lamp that has a similar
shape as a vehicle’s lamp.

[Headlights have been damaged or not
repaired properly.

[Headlights are not aimed properly.

[Driving on a narrow-curved road,
curved road, rough road, uphill or
downhill.
[Vehicle in front is partially visible on a
crossroad or curved road.

[There is a traffic light, reflecting sign,
flashing sign or mirror ahead.

[There is a temporary reflector or flash
ahead (construction area).

[The road conditions are bad such as
being wet, iced or covered with snow.

[A vehicle suddenly appears from a
curve.

[The vehicle is tilted from a flat tire or
is being towed.

[Light from an oncoming or front
vehicle is not detected due to
obstacles in the air such as exhaust
fume, smoke, fog, snow, or water spay
or blizzard on the road, or fogging in
the lamp, etc.
Information
For more details on the limitations of the
)URQW9LHZ&DPHUDUHIHUWR

5-119
05
WARNING
To avoid personal injury from the
windshield wipers, when the engine
is running and the windshield wiper
switch is placed in the AUTO mode:

[Do not touch the upper end of the
windshield glass facing the rain
sensor.

[Do not wipe the upper end of the
windshield glass with a damp or wet
cloth.

[Do not put pressure on the
windshield glass.
NOTICE

[When washing the vehicle, set the
ZLSHUVZLWFKLQWKH2))SRVLWLRQWR
stop the auto wiper operation. The
wiper may operate and be damaged
if the switch is set in the AUTO mode
while washing the vehicle.

[Do not remove the sensor cover
located on the upper end of the
passenger side windshield glass.
Damage to system components
could occur and may not be covered
by your vehicle warranty.

[Because of using a photo sensor,
temporary malfunction could occur
according to sudden ambient light
change made by stone and dust
while driving.
Windshield Washers
ORG3EV051079
In the OFF position, pull the lever gently
toward you to spray washer fluid on the
windshield.
The washer fluid is sprayed as the wipers
rise while operating. The spray and wiper
operation will continue until you release
the lever.
If the lever is released, the wipers
operate approximately 4 times and the
lever returns to it's original position

5-126
Convenience Features
Information
ORS051085
Never place anything near the ambient
light/solar sensor to ensure better control
of the heating and cooling system.
Manual Temperature Control
Mode
The heating and cooling system can be
controlled manually by pushing buttons
other than the AUTO button. In this case,
the system works sequentially according
to the order of buttons selected.
When pressing any button except the
AUTO button while using automatic
operation, the functions not selected will
be controlled automatically.
1. Start the vehicle.
2. Set the mode to the desired position.
To improve the effectiveness of
heating and cooling, select the mode
according to the following:

[Heating:

[Cooling:
3. Set the temperature control to the
desired position.
4. Set the air intake control to Fresh or
Recirculation mode.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn the
air conditioning system on.
7. Press the AUTO button to convert to
full automatic control of the system.
The climate control system settings
will be maintained, even when the
vehicle is turned OFF. However, the
climate control system settings will be
initialized when the battery has been
discharged, or when the cables have
been disconnected.
In this case, adjust the climate control
system settings again.

5-127
05
Mode selection
ORS052106N
A : Front seat control,
B : Rear seat control
Front seat mode selection

[Touch each air flow direction on the
climate control information screen to
select the desired flow direction.

[Press the SYNC button and when
the indicator light on the button
turns off, the air flow direction of the
driver’s seat, passenger seat, and rear
seat can be controlled individually.
However, passengers and rear seats
cannot select
.

[Touch REAR M to control the second
row seat mode selection from the
front seats.

[You may select 2~3 modes at the
same time.
ORS051108
ORS051142L
A : Rear seat control,
B : Front seat control
Rear seat mode selection

[Touch each air flow direction on the
armrest touchscreen to select the
desired air flow direction.

[Front seat air flow direction can be
selected individually for each seats.

[Air flow direction of the rear left and
right seats change together.

5-130
Convenience Features
Front windshield defroster
ORS051110
Defrost-level (A, D)
Press the button, and the indicator light
on the button will illuminate and the
windshield defroster indicator will appear
on the climate control information
screen.
Most of the air flow is directed to the
windshield with a small amount of air
directed to the side window defrosters.
When Defogging logic is enabled, Fresh
mode is selected and air conditioning
is selected according to outside
temperature.
Press the button again, the indicator light
will turn off and the previous settings will
be selected.
Instrument panel vents
ORS051111
ORS051112
A : Front seat,
B : Rear seat
The instrument panel vent air flow can be
directed up/down or left/right using the
vent adjustment lever.
The air flow can also be CLOSED using
the vent adjustment lever.
Move the lever to
position to close,
and to position to open.

5-131
05
Temperature control
ORS052113N
ORS052149N
A : Front seat control from the front,
B : Rear seat control from the front,
C : Rear seat control from the rear,
D : Front seat control from the rear
Set the desired temperature using
the temperature control switch or the
icon button on the climate control
information screen.

[Push the switch up (red) to increase
the temperature. Push the switch
down (blue) to decrease temperature/

[Press the icon (
/ ) in the
climate control information screen to
adjust the rear seat temperature from
the front seat.

[The temperature will increase or
decrease by 1°F (0.5°C) for each
incremental location. When set to
the lowest temperature setting,
the air conditioning will operate
continuously.
SYNC
ORS052117N
ORS052136N
A : Front seat,
B : Rear seat
$GMXVWLQJWKHWHPSHUDWXUHDLUIORZ
direction and fan speed equally

[Press the SYNC button (indicator
light ON) from the front seat, the
front and rear seat temperature, air
flow direction and fan speed will be
adjusted same as the driver’s control.

[Press the SYNC button (indicator
light ON) from the rear seat, the
front and rear seat temperature, air
flow direction and fan speed will
be adjusted same as the rear seat
control.

[The SYNC button does not operate
when the climate control system is off.

5-134
Convenience Features
Air conditioning
ORS052121N
ORS052138N
A : Front seat,
B : Rear seat
Touch the A/C icon to manually turn the
air conditioning on (indicator light on)
and off.
Built in diffuser (if equipped)
ORS051243L
ORS051125L
A : Front seat,
B : Rear seat
3 types of fragrances are provided.
The fragrance type is automatically
recognized when the cartridge is
installed.
Diffuser setting
Fragrance and its intensity can be set as
follows.

[ ,QIRWDLQPHQWV\VWHP
6HWXS

5-135
05
ORS051124
ORS051139L
A : Front seat,
B : Rear seat
Press from the climate control
information screen or armrest
touchscreen to select the desired
fragrance intensity.

[Intensity can be selected among
Strong, Medium and Light. Pressing
the button each time will change
the intensity in the order of Strong,
Medium, Light and Off.

[The fragrance cannot be selected with
the button. Fragrance can only be
selected from the settings menu.
ORS051244
How to replace cartridges
1. Turn the engine off, and open the
glove box.
2. Press the upper part of the diffuser
tray.
3. Replace the cartridge.
Information

[For smooth operation of diffuser, it is
recommended to install 2 cartridges.

[If the cartridge is empty or diffuser
replacement alarm is displayed, replace
with a new cartridge.

[The built-in diffuser may not work if
the cartridge is not installed properly.
&KHFNZKHWKHUWKHFDUWULGJHLVLQVWDOOHG
properly.