start stop button GENESIS G90 2023 Manual Online

6-38
Driving Your Vehicle
Good Braking Practices
WARNING
Whenever leaving the vehicle or
parking, always come to a complete
stop and continue to depress the brake
pedal. Shift the gear to the P (Park)
position, then apply the parking brake,
and press the Engine Start/Stop button
to the OFF position.
Vehicles parked with the parking brake
not applied or not fully engaged may
roll inadvertently and may cause injury
to the driver and others. ALWAYS apply
the parking brake before exiting the
vehicle.
Wet brakes can be dangerous! The
brakes may get wet if the vehicle is
driven through standing water or if it
is washed. Your vehicle will not stop as
quickly if the brakes are wet. Wet brakes
may cause the vehicle to pull to one side.
To dry the brakes, apply the brakes
lightly until the braking action returns to
normal. If the braking action does not
return to normal, stop as soon as it is safe
to do so and we recommend that you call
an authorized retailer of Genesis Branded
products for assistance.DO NOT drive with your foot resting on
the brake pedal. Even light, but constant
pedal pressure can result in the brakes
overheating, brake wear, and possibly
even brake failure.
If a tire goes flat while you are driving,
apply the brakes gently and keep the
vehicle pointed straight ahead while you
slow down. When you are moving slowly
enough for it to be safe to do so, pull off
the road and stop in a safe location.
Keep your foot firmly on the brake pedal
when the vehicle is stopped to prevent
the vehicle from rolling forward.

6-52
Driving Your Vehicle
Forced to Restart Engine
The engine is automatically restarted in
the following situations.

[The engine has stopped for about 5
minutes

[The air conditioning is ON with the fan
speed set to a certain high level

[The front defroster is ON

[The battery is weak

[The cooling and heating performance
of the climate control system is
unsatisfactory

[The vehicle is shifted to P (Park), N
(Neutral) or R (Reverse) when Auto
Hold is operating

[The door is opened or the seatbelt
is unfastened when Auto Hold is
activated

[The EPB switch is pressed when Auto
Hold is activated
The Auto Stop (
) indicator blinks in
green for 5 seconds on the instrument
cluster when the engine is restarted.
WARNING
When the engine is in Idle Stop mode,
the engine may restart without the
driver taking any action. Before leaving
the vehicle or working on the engine
compartment, turn off the engine by
pressing the ENGINE START/STOP
button to the OFF position.
ISG Malfunction
ISG system may not operate when there
is a malfunction with the ISG sensors or
ISG system.
The following will occur, when there is a
malfunction with the ISG system:

[The Auto Stop (
) indicator will
illuminate in yellow on the instrument
cluster.
Contact an authorized retailer of Genesis
Branded products.

7-84
Driver Assistance System
Smart Cruise Control conditions not
satisfied
OTM070112N
If the Driving Assist button, + switch,
- switch or switch is pushed
when Smart Cruise Control operating
conditions are not satisfied, the ‘Smart
Cruise Control conditions not met’ will
appear on the cluster, and an audible
warning will sound.
In traffic situation
OTM070114L
In traffic, your vehicle will stop if the
vehicle ahead of you stops. Also, if the
vehicle ahead of you starts moving, your
vehicle will start as well. In addition, after
the vehicle has stopped and a certain
time have passed, the ‘Use switch or
pedal to accelerate’ message will appear
on the cluster. Depress the accelerator
pedal or operate the + switch, - switch or
switch to start driving.
Warning road conditions ahead
ORS071120L
In the following situation, the ‘Watch for
surrounding vehicles’ warning message
will appear on the cluster, and an audible
warning will sound to warn the driver of
road conditions ahead.

[The vehicle in front disappears when
Smart Cruise Control is maintaining
the distance with the vehicle ahead
while driving below a certain speed.
:$51,1*
$OZD\VSD\DWWHQWLRQWRYHKLFOHVRU
REMHFWVWKDWPD\VXGGHQO\DSSHDULQ
IURQWRI\RXDQGLIQHFHVVDU\GHSUHVV
WKHEUDNHSHGDOWRUHGXFH\RXUGULYLQJ
speed in order to maintain a safe
GLVWDQFH

7-107
07
Information

[)RUPRUHGHWDLOVRQWKHGLVSOD\UHIHU
to “Smart Cruise Control (SCC)” and
“Lane Following Assist (LFA)” sections
LQWKLVFKDSWHU

[The images and colors in the
instrument cluster may differ
GHSHQGLQJRQWKHFOXVWHUW\SHRUWKHPH
selected from the settings menu.
+LJKZD\'ULYLQJ$VVLVWRSHUDWLRQ
Highway Driving Assist operates when:

[Driving on the main road of highways,
and turning on Highway Driving Assist
by pressing the Driving Assist button.

[Entering the main road of highways
while Lane Following assist and Smart
Cruise Control are operating
5HVWDUWLQJDIWHUVWRSSLQJ
OJWEV071266L
When Highway Driving Assist is
operating, your vehicle will stop if the
vehicle ahead of you stops. Also, if the
vehicle ahead of you starts moving
within 30 seconds after the stop, your
vehicle will start as well. In addition, after
the vehicle has stopped and 30 seconds
have passed, the ‘Use switch or pedal to
accelerate’ message will appear on the
cluster. Depress the accelerator pedal
or operate the + switch, - switch or

switch to start driving.

7-154
Driver Assistance System

['Agree' must be selected on the
infotainment system screen and the
infotainment system has to operate
properly to use Remote Operation
function.

[Method (2) can be used after the
vehicle has been driven above 3
mph (5 km/h).

[If the function is turned on again
after parking is completed by
Remote Smart Parking Assist,
Remote Operation function can be
used with Method (2).

[Check that all smart keys are
outside the vehicle when using
Remote Operation function.
5HPRWHO\PRYLQJIRUZDUGDQG
EDFNZDUG
ORS071036
(1) Press and hold one of the Forward
() or Backward () button on
the smart key. Remote Smart
Parking Assist will automatically
control the steering wheel, vehicle
speed and gearshift. The vehicle
will move in the direction of the
button pressed. (2) While Remote Operation function
is operating, if you do not
hold down the Forward (
) or
Backward () button, the vehicle
will stop and function control
will pause. The function will start
operating again when the button is
pressed and held again.
(3) When the vehicle reaches the
target location, release the smart
key Forward or Backward button.
(4) When the driver gets in the vehicle
with the smart key, a message
will appear informing the driver
Remote Operation function is
complete on the infotainment
system screen and the engine will
remain on.
In addition, when the Remote Start
(
) button is pressed on the smart
key from outside the vehicle, a
message will appear informing the
driver Remote Operation function
is complete and the engine will
turn off.

7-157
07
7KHIXQFWLRQZLOOSDXVHLQWKHIROORZLQJ
conditions when:

[There is a pedestrian, animal or object
in the direction the vehicle is moving

[The door or trunk is open

[The Forward (
) or Backward ()
button is not continuously pressed

[Simultaneously pressing multiple
buttons on a smart key

[The smart key is not operated within
13 ft. (4 m) from the vehicle

[Button of another smart key is pressed
in addition to the operating smart key

[Blind-Spot Collision-Avoidance
Assist or Rear Cross-Traffic Collision-
Avoidance Assist operates while the
vehicle is being controlled in the
reverse direction.

[The vehicle moves 22 ft. (7 m) while
the smart key is pressed with Remote
Operation function (maximum travel
distance per button press)
When Remote operation function is
paused, the vehicle will stop. If the
condition that made the function to
pause disappears, the function may
operate again.
The function will cancel in the following
conditions when:

[The steering wheel is steered

[The gear is shifted while the vehicle is
moving

[Operating EPB while the vehicle is
moving

[The hood is open

[The brake pedal or accelerator pedal
is depressed when all the doors are
closed

[The smart key is outside the vehicle
when the brake pedal is depressed
while the driver's door is open

[Rapid acceleration occurs

[Vehicle skid occurs

[The wheel is stuck by an obstacle and
cannot move

[Approximately 3 minutes and 50
seconds have past after Remote
Operation function has started to
operate

[The slope of the road exceeds the
operational range

[The function is paused for more than
1 minute

[The total travel distance of the vehicle
has exceeded 45 ft. (14 m) after
Remote Operation function operation

[The steering wheel, gearshift, braking,
and drive controls are not working
properly

[There is a problem with the smart key
or the smart key battery is low

[ABS, TCS or ESC system operates due
to slippery road conditions

[The alarm of the Theft Alarm System
sounds
When Remote Operation function is
canceled, the vehicle will automatically
stop, shift the gear to P (Park) and
engage EPB (Electronic Parking Brake).
The engine will turn off.

7-161
07
6PDUW3DUNLQJ
OJWEV071226L
OJWEV071227L
(1) Press the Parking/View
() button when the vehicle is
stopped by depressing the brake
pedal. When the brake pedal is
released, Remote Smart Parking
Assist will automatically control
the steering wheel, vehicle speed
and gearshift.
(2) While Smart Parking function
is operating, if you do not hold
down the Parking/View button,
the vehicle will stop and function
control will pause. The function
will start operating again when the
Parking/View button is pressed
and held again.(3) When the vehicle reaches the
target parking position, a message
will appear on the infotainment
system screen to inform you that
parking is complete.
(4) If you need to change the vehicle’s
position or location, manually
complete parking your vehicle.
Information

[6PDUW3DUNLQJIXQFWLRQZLOOQRW
RSHUDWHLIWKHGRRULVRSHQRUWKHVHDW
belt is not fastened.

[7KHSDUNLQJORFDWLRQLQGLFDWRULV
GLVSOD\HGRQ6XUURXQG9LHZ0RQLWRU
VFUHHQDQGLVGLVSOD\HGXQWLOWKHYHKLFOH
HQWHUVWKHSDUNLQJVSDFHIRUWKHILUVW
WLPHE\6PDUW3DUNLQJIXQFWLRQ

[9HKLFOHVSHHGFDQEHDGMXVWHGE\
GHSUHVVLQJWKHEUDNHSHGDOZKLOH6PDUW
3DUNLQJIXQFWLRQLVRSHUDWLQJ+RZHYHU
the vehicle does not accelerate
HYHQZKHQWKHDFFHOHUDWRUSHGDOLV
GHSUHVVHG

['HSHQGLQJRQSDUNLQJHQYLURQPHQWV
LIWKHYHKLFOHLVVWRSSHGE\DVWRSSHU
SDUNLQJPD\EHFRPSOHWHG

[If you need to change the vehicle's
SRVLWLRQRUORFDWLRQPDQXDOO\FRPSOHWH
SDUNLQJ\RXUYHKLFOH

7-162
Driver Assistance System
5HPRWH6PDUW3DUNLQJ
ORS071164L
(1) Shift the gear to P (Park), get out
of the vehicle with the smart key,
and close all doors.
(2) Press and hold one of the Forward
(
) or Backward () button on
the smart key. Remote Smart
Parking Assist will automatically
control the steering wheel, vehicle
speed and gearshift.
(3) While Remote Smart Parking
function is operating, if you do
not hold down the Forward (
) or
Backward () button, the vehicle
will stop and function control
will pause. The function will start
operating again when the button is
pressed and held again.
(4) When the vehicle reaches the
target parking position, a message
will appear on the infotainment
system screen to inform you that
parking is complete. The vehicle
will automatically shift to P (Park),
engage EPB (Electronic Parking
Brake) and the engine will turn off.
(5) If you need to change the vehicle’s
position or location, manually
complete parking your vehicle.
Information

[:KHQRSHUDWLQJ5HPRWH6PDUW
3DUNLQJIXQFWLRQPDNHVXUHDOOVPDUW
keys are outside of the vehicle.

[5HPRWH6PDUW3DUNLQJIXQFWLRQZLOO
RSHUDWHRQO\ZKHQWKHVPDUWNH\LV
ZLWKLQIWPIURPWKHYHKLFOH,I
there is no vehicle movement even when
the Remote Forward or Backward
EXWWRQLVSUHVVHGRQWKHVPDUWNH\
check the distance to the vehicle and
SUHVVWKHEXWWRQDJDLQ

[The detecting range of the smart
NH\PD\YDU\GHSHQGLQJRQWKH
surroundings that are affected by radio
waves such as transmission tower,
broadcast station, etc.

[7KHSDUNLQJORFDWLRQLQGLFDWRULV
GLVSOD\HGRQ6XUURXQG9LHZ0RQLWRU
VFUHHQDQGLVGLVSOD\HGXQWLOWKH
YHKLFOHHQWHUVWKHSDUNLQJVSDFHIRUWKH
ILUVWWLPHE\5HPRWH6PDUW3DUNLQJ
function.

['HSHQGLQJRQSDUNLQJHQYLURQPHQWV
LIWKHYHKLFOHLVVWRSSHGE\DVWRSSHU
SDUNLQJPD\EHFRPSOHWHG
CAUTION

[:KHQXVLQJ5HPRWH6PDUW3DUNLQJ
IXQFWLRQPDNHVXUHWKDWDOO
SDVVHQJHUVKDYHJRWWHQRXWRIWKH
YHKLFOH

[After ending or turning off Remote
6PDUW3DUNLQJIXQFWLRQEHIRUH
OHDYLQJWKHYHKLFOHFORVHZLQGRZV
DQGVXQURRIVDQGPDNHVXUHWKH
HQJLQHLVRIIEHIRUHORFNLQJWKH
GRRUV

7-164
Driver Assistance System
The function will pause in the
following conditions when:

[Smart Parking
- There is a pedestrian, animal or
object in the direction the vehicle is
moving
- The door or trunk is open
- The driver’s seat belt is not fastened
- Blind-Spot Collision-Avoidance
Assist or Rear-Cross Traffic
Collision-Avoidance Assist operates
while the vehicle is being controlled
in the reverse direction
- The Parking/View (
) button is
not continuously pressed
- The vehicle is stopped by
depressing the brake pedal

[Remote Smart Parking
- There is a pedestrian, animal or
object in the direction the vehicle is
moving
- The door or trunk is open
- The Forward (
) or Backward ()
button is not continuously pressed
- Simultaneously pressing multiple
buttons on a smart key
- The smart key is not operated within
13 ft. (4 m) from the vehicle
- Button of another smart key is
pressed in addition to the operating
smart key
- Blind-Spot Collision-Avoidance
Assist or Rear-Cross Traffic
Collision-Avoidance Assist, or
Parking Collision-Avoidance Assist
operates.
When Parking function is paused, the
vehicle will automatically stop. If the
condition that made the function to
pause disappears, the function may
operate again.
How to turn off Parking function
while operating

[Press the Parking/View () button
in the following stage:
- Searching for parking space
- Select parking type

[Shift the gear to R (Reverse) in the
following stage:
- Searching for parking space
- Select parking type
- Select operating mode

[Press the Parking Safety (
) button
or select ‘Cancel’ on the infotainment
system screen to turn off Parking
function.

[While Smart Parking function is
operating:
- If the vehicle is stopped by
depressing the brake pedal, and the
gear is shifted, Parking function will
turn off. At this time, EPB (Electronic
Parking Brake) will not be engaged.

[While Remote Smart Parking function
is operating:
- Press the Remote Start (
) button
on the smart key. Parking function
will turn off.
- Get on the vehicle with the smart
key. Parking function will turn off. At
this time, the engine will remain on.

7-167
07
6HOHFWH[LWGLUHFWLRQ
ORS071280L
(1) With the vehicle stopped by
depressing the brake pedal, the
infotainment system screen
displays the possible directions for
parallel exit.
(2) Touch the infotainment system
screen or use the central controller
to select the desired exit direction.
CAUTION

[%HIRUHVHOHFWLQJWKH([LW'LUHFWLRQ
WKHGULYHUVKRXOGFKHFNZKHWKHUWKH
VSDFHIRUH[LWLVVXLWDEOH

[,IWKHVHDUFKHGH[LWVSDFHE\5HPRWH
6PDUW3DUNLQJ$VVLVWLVQDUURZRU
XQVXLWDEOHVXUURXQGLQJYHKLFOHVDUH
SDUNHGYHUWLFDOO\HWFGRQRWXVH
WKH6PDUW([LWIXQFWLRQ
6PDUW([LW
ORS071278L
(1) Press the Parking/View
() button when the vehicle is
stopped by depressing the brake
pedal. When the brake pedal is
released, Remote Smart Parking
Assist will automatically control
the steering wheel, vehicle speed
and gearshift.
(2) While Smart Exit function is
operating, if you do not hold
down the Parking/View button,
the vehicle will stop and function
control will pause. The function
will start operating again when the
Parking/View button is pressed
and held again.
(3) When the vehicle reaches the
target exit location, a message will
appear on the infotainment system
screen to inform you that exit is
complete.