engine overheat GENESIS G90 2023 Owners Manual

Page 112 of 676

4
High beam indicator light ....................................................................................... 4-19
Low beam indicator light ........................................................................................4-20
Light ON indicator light ...........................................................................................4-20
High Beam Assist indicator light .............................................................................4-20
AUTO HOLD indicator light .....................................................................................4-20
LCD Display Messages ................................................................................................4-21
Vehicle is on ..............................................................................................................4-21
Shift to P ....................................................................................................................4-21
Vehicle is in N. Press START button and shift to P ..................................................4-21
Low key battery ........................................................................................................4-21
Press brake pedal to start engine ...........................................................................4-21
Key not in vehicle .....................................................................................................4-21
Key not detected .......................................................................................................4-21
Press START button again .......................................................................................4-21
Press START button with key ................................................................................... 4-22
Check BRAKE SWITCH fuse ................................................................................... 4-22
Shift to P or N to start engine .................................................................................. 4-22
Battery discharging due to external electrical devices ......................................... 4-22
Check rear wheel steering system .......................................................................... 4-22
Door, Hood, trunk open indicator ........................................................................... 4-23
Sunroof open indicator ............................................................................................ 4-23
Low tire pressure ..................................................................................................... 4-23
Lights ........................................................................................................................4-24
Wiper ........................................................................................................................ 4-24
Low washer fluid ...................................................................................................... 4-25
Low fuel .................................................................................................................... 4-25
Low engine oil .......................................................................................................... 4-25
Engine overheated ................................................................................................... 4-25
Check haptic steering wheel system ...................................................................... 4-25
Check headlight ....................................................................................................... 4-25
Check turn signal ..................................................................................................... 4-25
Check headlight LED ............................................................................................... 4-25
004_RS4_HMA.indd 4-22022-04-06  3:02:25

Page 116 of 676

4-6
Instrument Cluster, Armrest touchscreen, Infotainment system
Tachometer
ORS041006ORS041006
ORS042007NORS042007N
The tachometer indicates the
approximate number of engine
revolutions per minute (RPM).
Use the tachometer to select the correct
shift points and to prevent lugging and/
or over-revving the engine.
NOTICE
Do not operate the engine within the
tachometer's RED ZONE. This may
cause severe engine damage.
Engine coolant temperature gauge
ORS042008NORS042008N
ORS042009NORS042009N
This gauge indicates the temperature
of the engine coolant when the Engine
Start/Stop button is in the ON position.
NOTICE
If the gauge pointer moves beyond the
normal range area toward the “H (Hot)”
position, it indicates overheating that
may damage the engine.
Do not continue driving with an
overheated engine. If your vehicle
overheats, refer to “If the Engine
Overheats” section in chapter 8.
WARNING
Never remove the engine coolant
reservoir cap when the engine is hot.
The engine coolant is under pressure
and could cause severe burn. Wait until
the engine is cool before adding coolant
to the reservoir.
004_RS4_HMA.indd 4-62022-04-06  3:02:27

Page 135 of 676

4-25
04
Low washer fluid
This message is displayed if the washer
fluid level in the reservoir is nearly empty.
Have the washer fluid reservoir refilled.
Low fuel
This message is displayed if the fuel tank
is almost out of fuel.
When this message is displayed, the low
fuel level warning light in the cluster will
come on.
It is recommended to look for the nearest
fueling station and refuel as soon as
possible.
Low engine oil (if equipped)
This warning message is displayed when
the engine oil level should be checked.
If this warning message is displayed,
check the engine oil level as soon as
possible and add engine oil as required.
Slowly pour the recommended oil little
by little into a funnel.
Use only the specified engine oil. (Refer
to "Recommended Lubricants and
Capacities“ section in chapter 2.)
Do not overfill the engine oil. Make sure
the oil level is not above F (Full) mark on
the dipstick.
Information
After adding engine oil, if you travel
approximately 31~62 miles (50~100 km)
after the engine warms up, the warning
message should disappear.
Engine overheated
This message is displayed when the
engine coolant temperature is above
248°F (120°C). This means that the
engine is overheated and may be
damaged.
If your vehicle is overheated, refer to
“Overheating” section in chapter 8.
Check haptic steering wheel system
This message is displayed if there is a
problem with the haptic steering wheel
system. Have the vehicle inspected by an
authorized retailer of Genesis Branded
products.
Check headlight (if equipped)
This message is displayed if the
headlights are not operating properly. A
lamp may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.
Check turn signal (if equipped)
This message is displayed if the turn
signal lamps are not operating properly.
A lamp may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.
Check headlight LED (if equipped)
This message is displayed if there is a
problem with the LED headlight. Have
the vehicle inspected by an authorized
retailer of Genesis Branded products.
004_RS4_HMA.indd 4-252022-04-06  3:02:33

Page 278 of 676

5-137
05
Air conditioning
Your Genesis Branded Vehicle air
conditioning system is filled with
R-1234yf refrigerant.
1. Start the vehicle.
2. Press the air conditioning button.
3. Set the mode to the Face Level

mode.
4. Set the air intake control to
Recirculation mode temporarily to
allow the cabin to cool quickly. When
the desired temperature in the cabin
is reached, change the air intake
control back to Fresh mode.
5. Adjust the fan speed control and
temperature control to maintain
maximum comfort.
When maximum cooling is desired, set
the temperature control to the lowest
position, then set the fan speed control
to the highest setting.
NOTICE
When using the air conditioning system,
monitor the engine temperature gauge
closely while driving up hills or in heavy
traffic when outside temperatures are
high. Air conditioning system operation
when climbing a steep grade or in
high outside ambient temperatures
can cause engine overheating.
Continue to use the fan, but turn the air
conditioning system off if the engine
temperature gauge indicates engine
overheating.
Air conditioning system operation tips
[If the vehicle has been parked in
direct sunlight during hot weather,
open the windows for a short time
to let the hot air inside the vehicle
escape.
[After sufficient cooling has been
achieved, switch back from
recirculation mode to fresh mode.
[To help reduce moisture inside of
the windows on rainy or humid
days, decrease the humidity inside
the vehicle by operating the air
conditioning system with the windows
and sunroof closed.
[Use the air conditioning system
every month only for a few minutes
to ensure maximum system
performance.
[If you operate air conditioner
excessively, the difference between
the temperature of the outside air and
that of the windshield could cause
the outer surface of the windshield to
fog up, causing loss of visibility. In this
case, set the mode selection to the

position and fan speed control to the
lowest speed.

Page 297 of 676

5-156
Convenience Features
Power Outlet
ORS051096
ORS051097
A : Front seat,
B : Rear seat
The power outlet is designed to provide
power for mobile telephones or other
devices designed to operate with vehicle
electrical systems. The devices should
draw less than 180 W with the engine
running.
WARNING
Avoid electrical shocks. Do not place
your fingers or foreign objects (pin, etc.)
into a power outlet or touch the power
outlet with a wet hand.
NOTICE
To prevent damage to the power
outlets:
[Use the power outlet only when the
engine is running and remove the
accessory plug after use. Using the
accessory plug for prolonged periods
of time with the engine off could
cause the battery to discharge.
[Only use 12V electric accessories
which are less than 180 W in electric
capacity.
[Adjust the air-conditioner or heater
to the lowest operating level when
using the power outlet.
[Close the cover when not in use.
[Some electronic devices can
cause electronic interference
when plugged into a vehicle’s
power outlet. These devices may
cause excessive audio static and
malfunctions in other electronic
systems or devices used in your
vehicle.
[Push the plug in as far as it will go. If
good contact is not made, the plug
may overheat and the fuse may open.
[Plug in battery equipped electrical/
electronic devices with reverse
current protection. The current
from the battery may flow into the
vehicle’s electrical/electronic system
and cause system malfunction.

Page 326 of 676

6-16
Driving Your Vehicle
CAUTION
When you start after stopping on a
steep incline, even if the gear is in
D (Drive), if you do not depress the
accelerator or brake pedal, the vehicle
may roll backwards, which can cause an
accident.
When the battery is discharged
You cannot shift gears, when the battery
is discharged.
In emergencies, do the following to shift
the gear to N (Neutral) on a level ground.
1. Connect the battery cables from
another vehicle or from a another
battery to the jump-starting terminals
inside the engine compartment.
For more details, refer to "Jump
Starting" section in chapter 8.
2. Release the Electronic Parking Brake
with the Engine Start/Stop button in
the ON position.
3. Shift the gear to the N (Neutral)
position. Refer to the “To stay in N
(Neutral) when vehicle is OFF” in this
chapter.
Information
In situations when the gear needs to be
shifted from P (Park) to N (Neutral) when
the Engine Start/Stop button is in the
OFF position, refer to the “To stay in N
(Neutral) when vehicle is OFF” in this
chapter.
Shift-lock system
For your safety, the automatic
transmission has a shift-lock system
which prevents shifting the transmission
from P (Park) into R (Reverse) or D (Drive)
unless the brake pedal is depressed.
To shift from P (Park) or N (Neutral) into R
(Reverse) or D (Drive):
1. Depress and hold the brake pedal.
2. Start the engine.
3. Shift gear while depressing the brake
pedal.
Parking
Always come to a complete stop and
continue to depress the brake pedal.
Shift the gear to P (Park), apply the
parking brake, and press the Engine
Start/Stop button to the OFF position.
Take the Key with you when leaving the
vehicle.
WARNING
[When you stay in the vehicle with
the engine running, be careful not
to depress the accelerator pedal for
a long period of time. The engine or
exhaust system may overheat and
start a fire.
[The exhaust gas and the exhaust
system are very hot. Keep away from
the exhaust system components.
[Do not stop or park over flammable
materials, such as dry grass, paper
or leaves. They may ignite and cause
a fire.

Page 329 of 676

6-19
06
Check shifter dial
OJWEV061002L
This message is displayed when there is
a malfunction with the shift dial.
Have the vehicle inspected by an
authorized retailer of Genesis Branded
products.
Check P button
OJWEV061003L
This message is displayed when there is
a problem with the P button.
Have the vehicle inspected by an
authorized retailer of Genesis Branded
products.
Transmission overheated warning
ORS061046L
Transmission Hot! Park with engine on
Repeated sudden acceleration and quick
start may overheat the transmission. If
the transmission is overheated, the self-
protection mode alarms the driver with
an audible sound warning message.
[Move the vehicle to a safe location
and shift the gear to P (Park), and stop
the vehicle with the engine on. Wait
until the transmission is sufficiently
cooled down.

Page 330 of 676

6-20
Driving Your Vehicle
ORS061031L
Vehicle Power limited due to high
transmission temperature
If you continue to drive with overheated
transmission, the above warning
message is displayed and self-protection
mode restricts the power output of the
vehicle.
[Move the vehicle to a safe location
and shift the gear to P (Park), and stop
the vehicle with the engine on. Wait
until the transmission is sufficiently
cooled down.
[If the above message is continuously
displayed, have you contact an
authorized retailer of Genesis Branded
products.
ORS061047L
Transmission cooled and safe to drive
This message is displayed when the
vehicle is safe to drive.

Page 331 of 676

6-21
06
Paddle Shifter (Manual Shift
Mode)
ORS061009
The paddle shifter allows the driver to
shift gears without taking one’s hands off
the steering wheel.
The paddle shifter operates as follow.
[Pull the [+] or [-] paddle shifter once
to shift up or down one gear and the
system changes from automatic shift
mode to manual shift mode.
[To change back to automatic shift
mode from manual shift mode, do one
of the following:
-Pull the [+] paddle shifter for more
than one second.
-Drive the vehicle under 4 mph (7
km/h)
-Gently depress the accelerator
pedal for more than 6 seconds.
-Rotate the shift dial to the D (Drive)
position.
Information
If the [+] and [-] paddle shifters are pulled
at the same time, gear shift may not occur.
Good Driving Practices
[Never shift the gear from P (Park) or
N (Neutral) to any other position with
the accelerator pedal depressed.
[Never shift the gear into P (Park) when
the vehicle is in motion.
Be sure the vehicle is completely
stopped before you attempt to shift
into R (Reverse) or D (Drive).
[Do not shift the gear to N (Neutral)
when driving. If the gear is shifted to
N (Neutral) while driving, the vehicle
loses the ability to provide engine
braking. Doing so may increase the
risk of an accident.
Also, shifting the gear back to
D (Drive) while the vehicle is
moving may severely damage the
transmission.
[When driving uphill or downhill,
always shift to D (Drive) for driving
forward or shift to R (Reverse) for
driving rearwards. After selecting
D (Drive) or R (Reverse), check the
gear position indicated on the cluster
before driving. If the vehicle moves in
the opposite direction of the selected
gear, the engine may turn off and a
serious accident might occur due to
degraded brake performance.
[Do not drive with your foot resting
on the brake pedal. Even light, but
consistent pedal pressure can result
in the brakes overheating, brake wear
and possibly even brake failure.

Page 336 of 676

6-26
Driving Your Vehicle
Warning messages
ORS061053L
To release EPB, fasten seatbelt, close door,
hood and trunk
[If you try to drive with EPB applied, a
warning will sound and a message will
appear.
[If the driver's seat belt is unfastened
and the engine hood or trunk is
opened, a warning will sound and a
message will appear.
[If there is a problem with the vehicle,
a warning may sound and a message
may appear.
If the situation occurs, depress the brake
pedal and release EPB by pressing the
EPB switch.
WARNING
[Whenever leaving the vehicle or
parking, always come to a complete
stop and continue to depress the
brake pedal.
Shift the gear into P (Park), pull the
EPB switch, and press the Engine
Start/Stop button to the OFF
position. Take the Key with you when
leaving the vehicle.
Vehicles not fully engaged in P (Park)
with the parking brake set are at risk
for moving inadvertently and causing
injury to yourself or others.
[NEVER allow anyone who is
unfamiliar with the vehicle to touch
the EPB switch. If EPB is released
unintentionally, serious injury may
occur.
[Only release EPB when you are
seated inside the vehicle with your
foot firmly on the brake pedal.
NOTICE
[Do not apply the accelerator pedal
while the parking brake is engaged.
If you depress the accelerator pedal
with EPB engaged, a warning will
sound and a message will appear.
Damage to the parking brake may
occur.
[Driving with the parking brake on
can overheat the braking system and
cause premature wear or damage
to brake parts. Make sure EPB is
released and the Parking Brake
warning light is off before driving.
Information
[A clicking sound may be heard while
operating or releasing the EPB. These
conditions are normal and indicate that
EPB is functioning properly.
[When leaving your keys with a parking
attendant or assistant, make sure to
inform him/her how to operate EPB.

Page:   1-10 11-20 21-30 next >