brake GENESIS GV60 2023 Owners Manual

Page 489 of 690

7-75
07
OJWEV071133
Decreasing set speed
[Push the - switch down and release
it immediately. The set speed will
decrease by 1 mph (1 km/h) each time
the switch is operated in this manner.
[Push the - switch down and hold it
while monitoring the set speed on the
cluster. The set speed will decrease by
5 mph (10 km/h) each time the switch
is operated in this manner.
Release the switch at the speed you
want to maintain. You can set the
speed to 20 mph (30 km/h).
OJWEV071134
Temporarily cancelling Smart Cruise
Control
Press the switch or depress the
brake pedal to temporarily cancel Smart
Cruise Control.
OJWEV071135
Resuming Smart Cruise Control
To resume Smart Cruise Control after the
function was cancelled, operate the +, -
or
switch.
If you push the + switch up or - switch
down, vehicle speed will be set to the
current speed on the cluster.
If you press the
switch, vehicle
speed will resume to the preset speed.
:$51,1*
&KHFNWKHGULYLQJFRQGLWLRQEHIRUH
using the VZLWFK'ULYLQJVSHHG
PD\VKDUSO\LQFUHDVHRUGHFUHDVHZKHQ
\RXSUHVVWKH
VZLWFK

Page 492 of 690

7-78
Driver Assistance System
OTM070113N
Temporarily cancelling Smart Cruise
Control
Smart Cruise Control will be temporarily
cancelled automatically when:
[The vehicle speed is above 130 mph
(210 km/h)
[The vehicle is stopped for a certain
period of time
[The accelerator pedal is continuously
depressed for a certain period of time
[The conditions for the Smart Cruise
Control to operate is not satisfied
If Smart Cruise Control is temporarily
cancelled automatically, the ‘Smart
Cruise Control cancelled’ warning
message will appear on the cluster, and
an audible warning will sound to warn
the driver.
Information
If Smart Cruise Control is temporarily
cancelled while the vehicle is at a
standstill with the function activated,
EPB (Electronic Parking Brake) maybe
applied.
:$51,1*
When Smart Cruise Control is
WHPSRUDULO\FDQFHOOHGGLVWDQFHZLWK
WKHIURQWYHKLFOHZLOOQRWEHPDLQWDLQHG
$OZD\VKDYH\RXUH\HVRQWKHURDG
ZKLOHGULYLQJDQGLIQHFHVVDU\GHSUHVV
WKHEUDNHSHGDOWRUHGXFH\RXUGULYLQJ
speed in order to maintain a safe
GLVWDQFH
OTM070112N
Smart Cruise Control conditions not
satisfied
If the Driving Assist button, + switch,
- switch or switch is operated
when Smart Cruise Control operating
conditions are not satisfied, the ‘Smart
Cruise Control conditions not met’ will
appear on the cluster, and an audible
warning will sound.

Page 494 of 690

7-80
Driver Assistance System
OJWEV071001L
Collision Warning
While Smart Cruise Control is operating,
when the collision risk with the vehicle
ahead is high, the ‘Collision Warning’
warning message will appear on the
cluster, and an audible warning will
sound to warn the driver. Always have
your eyes on the road while driving, and
if necessary, depress the brake pedal to
reduce your driving speed in order to
maintain a safe distance.
:$51,1*
,QWKHIROORZLQJVLWXDWLRQV6PDUW&UXLVH
&RQWUROPD\QRWZDUQWKHGULYHURID
FROOLVLRQ
[7KHGLVWDQFHIURPWKHIURQWYHKLFOH
LVQHDURUWKHYHKLFOHVSHHGRIWKH
IURQWYHKLFOHLVIDVWHURUVLPLODUZLWK
\RXUYHKLFOH
[7KHVSHHGRIWKHIURQWYHKLFOHLVYHU\
slow or is at a standstill
[The accelerator pedal is depressed
right after Smart Cruise Control is
turned on
:$51,1*
Take the following precautions when
using Smart Cruise Control:
[Smart Cruise Control does not
VXEVWLWXWHIRUSURSHUDQGVDIH
GULYLQJ,WLVWKHUHVSRQVLELOLW\RIWKH
GULYHUWRDOZD\VFKHFNWKHVSHHGDQG
GLVWDQFHWRWKHYHKLFOHDKHDG
[6PDUW&UXLVH&RQWUROPD\QRW
UHFRJQL]HXQH[SHFWHGDQGVXGGHQ
VLWXDWLRQVRUFRPSOH[GULYLQJ
VLWXDWLRQVVRDOZD\VSD\DWWHQWLRQWR
GULYLQJFRQGLWLRQVDQGFRQWURO\RXU
YHKLFOHVSHHG
[.HHS6PDUW&UXLVH&RQWURORIIZKHQ
WKHIXQFWLRQLVQRWLQXVHWRDYRLG
LQDGYHUWHQWO\VHWWLQJDVSHHG
['RQRWRSHQWKHGRRURUOHDYHWKH
YHKLFOHZKHQ6PDUW&UXLVH&RQWURO
LVRSHUDWLQJHYHQLIWKHYHKLFOHLV
VWRSSHG
[$OZD\VEHDZDUHRIWKHVHOHFWHG
VSHHGDQGKHDGZD\GLVWDQFH
[.HHSDVDIHGLVWDQFHDFFRUGLQJWR
URDGFRQGLWLRQVDQGYHKLFOHVSHHG
,IWKHKHDGZD\GLVWDQFHLVWRRFORVH
GXULQJKLJKVSHHGGULYLQJDVHULRXV
FROOLVLRQPD\UHVXOW

Page 496 of 690

7-82
Driver Assistance System
CAUTION
[7KHYHKLFOHPXVWEHGULYHQ
VXIILFLHQWO\WRUHIOHFWWKHDFWXDO
GULYLQJVW\OHRIWKHGULYHUVXFKDV
LQWHUYHKLFOHGLVWDQFHDFFHOHUDWLRQ
DQGUHDFWLRQVSHHG
[%DVHGRQ'ULYLQJVW\OHGRHVQRW
UHIOHFWZKHWKHUWKHGULYHUKDV
changed when determining the
GULYHU
VGULYLQJVW\OH
[,I\RXDUHGULYLQJLQVSHFLDO
FRQGLWLRQVVXFKDVVQRZUDLQIRJ
RUVWHHSVORSHVWKHYHKLFOHPD\QRW
EHGULYHQDFFRUGLQJWRWKHGULYHUTV
GULYLQJVW\OH
Information
[Smart Cruise Control may not operate
for 15 seconds after the vehicle is
started or the front view camera or
front radar is initialized.
[You may hear a sound when the brake
is controlled by Smart Cruise Control.
[Based on Driving Style may not reflect
the driver’s driving style or driving
conditions that affects driving safety.
[Based on Driving Style does not reflect
any other driving style other than
inter-vehicle distance, acceleration and
reaction speed.
Smart Cruise Control
Malfunction and Limitations
Smart Cruise Control malfunction
OJWEV071257L
When Smart Cruise Control is not working
properly, the ‘Check Smart Cruise Control
system’ warning message will appear, and
the
warning light will illuminate on the
cluster. If this occurs, have the vehicle
be inspected by an authorized retailer of
Genesis Branded products.

Page 499 of 690

7-85
07
[Driving on a curved road
OJWEV071056
On curves, Smart Cruise Control may
not detect a vehicle in the same lane,
and may accelerate to the set speed.
Also, vehicle speed may rapidly
decrease when the vehicle ahead is
detected suddenly.
Select the appropriate set speed on
curves and apply the brake pedal or
accelerator pedal according to the
road and driving conditions ahead.
OJWEV071059
Your vehicle speed can be reduced
due to a vehicle in the adjacent lane.
Apply the accelerator pedal and select
the appropriate set speed. Check
to be sure that the road conditions
permit safe operation of the Smart
Cruise Control. [Driving on an inclined road
OJWEV071062
During uphill or downhill driving, the
Smart Cruise Control may not detect
a moving vehicle in your lane, and
cause your vehicle to accelerate to
the set speed. Also, vehicle speed will
rapidly decrease when the vehicle
ahead is detected suddenly.
Select the appropriate set speed on
inclines and apply the brake pedal or
accelerator pedal according to the
road and driving conditions ahead.

Page 500 of 690

7-86
Driver Assistance System
[Changing lanes
OJWEV071065 [A] : Your vehicle,
[B] : Lane changing vehicle
When a vehicle moves into your lane
from an adjacent lane, it cannot be
detected by the sensor until it is in the
sensor's detection range. Smart Cruise
Control may not immediately detect
the vehicle when the vehicle changes
lanes abruptly. In this case, you must
maintain a safe braking distance, and
if necessary, depress the brake pedal
to reduce your driving speed in order
to maintain a safe distance.[Situations when detecting are limited
OJWEV071137
OJWEV071067
In the following cases, some vehicles
in your lane cannot be detected by the
sensor:
- Vehicles offset to one side
- Slow-moving vehicles or sudden-
decelerating vehicles
- Vehicles with higher ground
clearance or vehicles carrying loads
that stick out of the back of the
vehicle
- Vehicles that has the front lifted
dueto heavy loads
- Vehicles within approximately 6
feet(2 m) from your vehicle
- Oncoming vehicles
- Stopped vehicles
- Vehicles with small rear profile, such
as trailers

Page 501 of 690

7-87
07
- Narrow vehicles, such as
motorcycles or bicycles
- Special vehicles
- Animals and pedestrians
Adjust your vehicle speed by
depressing the brake pedal according
to the road and driving conditions
ahead.
In the following cases, the vehicle
in front cannot be detected by the
sensor:
- You are steering your vehicle
- Driving on narrow or sharply curved
roads
Adjust your vehicle speed by
depressing the brake pedal according
to the road and driving conditions
ahead.
OJWEV071138
[When a vehicle ahead disappears
at an intersection, your vehicle may
accelerate.
Always pay attention to road and
driving conditions while driving.
OJWEV071139
[When a vehicle in front of you merges
out of the lane, Smart Cruise Control
may not immediately detect the new
vehicle that is now in front of you.
Always pay attention to road and
driving conditions while driving.
OJWEV071140
[Always look out for pedestrians when
your vehicle is maintaining a distance
with the vehicle ahead.

Page 506 of 690

7-92
Driver Assistance System
Highway Curve Zone Auto Slowdown
[Depending on the curve ahead on the
highway (or motorway), the vehicle
will decelerate, and after passing the
curve, the vehicle will accelerate to
Smart Cruise Control set speed.
[Vehicle deceleration time may differ
depending on the vehicle speed
and the degree of the curve on the
road. The higher the driving speed,
deceleration will start faster.
Highway Set Speed Auto Change
[Highway Set Speed Auto Change
function will operate when Smart
Cruise Control set speed and the
highway (or motorway) speed limit is
matched.
[While Highway Set Speed Auto
Change function is operating, when
the highway (or motorway), speed
limit changes, Smart Cruise Control
set speed automatically changes to
the changed speed limit.
[If Smart Cruise Control set speed is
adjusted different from the speed
limit, Highway Set Speed Auto Change
function will be in the standby state.
[If Highway Set Speed Auto Change
function has changed to the standby
state by driving on a road other than
the highway (or motorway) main road,
Highway Set Speed Auto Change
function will operate again when you
drive on the main road again without
setting the set speed.[If Highway Set Speed Auto Change
function has changed to the standby
state by depressing the brake pedal
or pressing the
switch on the
steering wheel, press the switch
to restart the function.
[Highway Set Speed Auto Change
function does not operate on highway
interchanges or junctions.
Information
[Highway Set Speed Auto Change
function only operates based on
the speed limits of the highway (or
motorway), it does not work with the
speed cameras.
[When Highway Set Speed Auto Change
function is operating, the vehicle
automatically accelerates or decelerates
when the highway (or motorway) speed
limit changes.
[The maximum set speed for Highway
Set Speed Auto Change function is 86
mph (140 km/h).
[If the speed limit of a new road is not
updated in the navigation, Highway Set
Speed Auto Change function may not
operate properly.
[If the speed unit is set to a unit other
than the speed unit used in your
country, Highway Set Speed Auto
Change function may not operate
properly.

Page 520 of 690

7-106
Driver Assistance System
[Driving to one side within lane (if
equipped)
OJWEV071182
When vehicle speed is above 40
mph (60 km/h), if a detected vehicle
around you is driving at a close
distance, your vehicle will control
steering in the opposite direction of
the vehicle to assist in safe driving.
If there a detected vehicle in both
sides of the lane that are driving close
to you, the function will not veer to
the opposite side of the lane.
+LJKZD\'ULYLQJ$VVLVWVWDQGE\
When the Smart Cruise Control is
temporarily cancelled while Highway
Driving Assist is operating, Highway
Driving Assist will be in the standby state.
At this time, Lane Following Assist will
operate properly.
Information
[Driving Speed Limit helps you drive
below 40 mph (60 km/h). At this time,
the vehicle decelerates due to the
vehicle ahead. After the vehicle has
decelerated, it cannot automatically
accelerate.
[Driving Speed Limit will cancel in the
following circumstances:
-When the driver grabs the steering
wheel again
-When the driver turns on Lane
Following Assist by pressing the Lane
Driving Assist button
-When Smart Cruise Control switch
+, -,
or button is operated,
or the accelerator pedal or the brake
pedal is depressed

Page 544 of 690

7-130
Driver Assistance System
Rear Cross-Traffic Collision-
$YRLGDQFH$VVLVW2SHUDWLRQ
Warning and control
Rear Cross-Traffic Collision-Avoidance
Assist will warn and control the vehicle
depending on collision risk level:
‘Collision Warning’, ‘Emergency Braking’
and ‘Stopping vehicle and ending brake
control’.
OPDEN060039OJWEV071040N
OJWEV071225L
Collision Warning
[To warn the driver of an approaching
a detected vehicle from the rear left/
right side of your vehicle, the warning
light on the outside rearview mirror
will blink and a warning will appear
on the cluster. At the same time, an
audible warning will sound and the
steering wheel will vibrate. If the Rear
View Monitor is operating, a warning
will also appear on the infotainment
system screen.[Rear Cross-Traffic Collision-Avoidance
Assist will operate when all the
following conditions are satisfied:
- The gear is shifted to R (Reverse)
- Vehicle speed is below 5 mph (8
km/h)
- The approaching a detected vehicle
is within approximately 82 ft. (25 m)
from the left and right side of your
vehicle
- The speed of the a detected vehicle
approaching from the left and right
is above 3 mph (5 km/h)
Information
[If the operating conditions are satisfied,
there will be a warning whenever the
vehicle approaches from the left or
right side even though your vehicle
speed is 0 mph (0 km/h).
[The images and colors in the cluster
may differ depending on the cluster
type or theme selected from the cluster.

Page:   < prev 1-10 ... 61-70 71-80 81-90 91-100 101-110 111-120 121-130 131-140 141-150 ... 150 next >