display GENESIS GV60 2023 Manual Online
Page 483 of 690
7-69
07
Blind-Spot View Monitor
Operating conditions
When the left or right side turn signal
turns on, the image in that direction is
displayed on the instrument cluster.
Off conditions
[ When the turn signal turns off, the
image on the instrument cluster will
turn off.
[ When the hazard warning flasher
is on, Blind-Spot View Monitor will
turn off, regardless of the turn signal
status.
[ When other important warning is
displayed on the instrument cluster,
Blind-Spot View Monitor may turn off.
% O L Q G 6 S R W 9 L H Z 0 R Q L W R U
Malfunction
When Blind-Spot View Monitor is not
working properly, or the cluster display
flickers, or the camera image does not
display properly, have the vehicle be
inspected by an authorized retailer of
Genesis Brand products.
: $ 5 1 , 1 *
[ 7 K H L P D J H V K R Z Q R Q W K H F O X V W H U P D \
differ from the actual distance of the
R E M H F W 0 D N H V X U H W R G L U H F W O \ F K H F N
W K H Y H K L F O H
V V X U U R X Q G L Q J V I R U V D I H W \
[ $ O Z D \ V N H H S W K H F D P H U D O H Q V F O H D Q
, I W K H O H Q V L V F R Y H U H G Z L W K I R U H L J Q
P D W H U L D O L W P D \ D G Y H U V H O \ D I I H F W
F D P H U D S H U I R U P D Q F H D Q G % O L Q G
6 S R W 9 L H Z 0 R Q L W R U P D \ Q R W R S H U D W H
S U R S H U O \
Page 490 of 690
7-76
Driver Assistance System
OJWEV071081
Turning off Smart Cruise Control
Press the Driving Assist () button to
turn Smart Cruise Control off.
Information
If your vehicle is equipped with Manual
Speed Limit Assist, press and hold the
Driving Assist (
) button to turn off
Smart Cruise Control. However Manual
Speed Limit Assist will turn on.
Display and control
You can see the status of the Smart
Cruise Control operation in the Driving
Assist view on the cluster. Refer to “View
Modes” section in chapter 4.
Smart Cruise Control will be displayed
as below depending on the status of the
function.
OJWEV071028E
Basic function
[ When operating
(1) Whether there is a vehicle ahead and
the selected distance level
(2) Set speed
(3) Whether there is a vehicle ahead and
the target vehicle distance
[ When temporarily cancelled
(1) Your vehicle (shaded)
(2) The previous set speed (shaded)
(3) Whether there is a vehicle ahead
(shaded) (if equipped)
Page 491 of 690
7-77
07
Information
[ The distance of the front vehicle on the
cluster is displayed according to the
actual distance between your vehicle
and the vehicle ahead.
[ The target distance may vary according
to the vehicle speed and the set
distance level. If the vehicle speed is
low, even though the vehicle distance
have changed, the change of the target
vehicle distance may be small.
[ The images and colors in the cluster
may differ depending on the cluster
type or theme selected from the cluster.
OJWEV071147E
Accelerating temporarily
If you want to speed up temporarily
without altering the set speed while
Smart Cruise Control is operating,
depress the accelerator pedal. While the
accelerator pedal is depressed, the set
speed, distance level and target distance
will blink on the cluster.
However, if the accelerator pedal is
depressed insufficiently, the vehicle may
decelerate.
: $ 5 1 , 1 *
% H F D U H I X O Z K H Q D F F H O H U D W L Q J
W H P S R U D U L O \ E H F D X V H W K H V S H H G D Q G
G L V W D Q F H L V Q R W F R Q W U R O O H G D X W R P D W L F D O O \
H Y H Q L I W K H U H L V D Y H K L F O H L Q I U R Q W R I \ R X
OJWEV071295LOJWEV071032E
Based on Driving Style operating
When Based on Driving Style is
operating, ‘Driving Style Adaptive SCC’
message will appear on the cluster for
2 seconds, and the distance level and
target distance will be displayed based
on the driving style.
Page 493 of 690
7-79
07
OJWEV071037L
In traffic situation
In traffic, your vehicle will stop if the
vehicle ahead of you stops. Also, if the
vehicle ahead of you starts moving, your
vehicle will start as well. In addition, after
the vehicle has stopped and a certain
time have passed, the ‘Use switch or
pedal to accelerate’ message will appear
on the cluster. Depress the accelerator
pedal or operate the + switch, - switch or
switch to start driving.
OJWEV071149L
Warning road conditions ahead
In the following situation, the ‘Watch for
surrounding vehicles’ warning message
will appear on the cluster, and an audible
warning will sound to warn the driver of
road conditions ahead.
[ The vehicle in front disappears when
Smart Cruise Control is maintaining
the distance with the vehicle ahead
while driving below a certain speed.
[ While the ‘Use switch or pedal to
accelerate’ message is displayed on
the cluster, if there is no vehicle in
front or the vehicle is far away from
you, and the + switch, – switch or
switch is operated.
: $ 5 1 , 1 *
$ O Z D \ V S D \ D W W H Q W L R Q W R Y H K L F O H V R U
R E M H F W V W K D W P D \ V X G G H Q O \ D S S H D U L Q
I U R Q W R I \ R X D Q G L I Q H F H V V D U \ G H S U H V V
W K H E U D N H S H G D O W R U H G X F H \ R X U G U L Y L Q J
speed in order to maintain a safe
G L V W D Q F H
Page 518 of 690
7-104
Driver Assistance System
Information
For more details on the display refer to
“Smart Cruise Control (SCC)” and “Lane
Following Assist (LFA)” sections in this
chapter.
+ L J K Z D \ ' U L Y L Q J $ V V L V W R S H U D W L Q J
Highway Driving Assist operates when:
[ Driving on the main road of highways,
and turning on Highway Driving Assist
by pressing the Driving Assist (
)
button.
[ Entering the main road of highways
while Lane Following assist and Smart
Cruise Control are operating
Information
The images and colors in the cluster may
differ depending on the cluster type or
theme selected from the cluster.
Information
[ While driving on the highway (or
motorway), if Smart Cruise Control
starts operating, Highway Driving
Assist will operate.
[ When entering the main roads of
highways (or motorways) while
Smart Cruise Control is operating,
Driving Assist will not turn on if Lane
Following Assist is turned off.[ Restarting after stopping
OJWEV071266L
When Highway Driving Assist is
operating, your vehicle will stop if the
vehicle ahead of you stops. Also, if the
vehicle ahead of you starts moving
within 30 seconds after the stop, your
vehicle will start as well. In addition,
after the vehicle has stopped and 30
seconds have passed, the ‘Use switch
or pedal to accelerate’ message will
appear on the cluster. Depress the
accelerator pedal or operate the +
switch, - switch or
switch to start
driving.
Page 521 of 690
7-107
07
Highway Lane Change Assist (if
equipped)
Display and control
You can see the status of the Highway
Lane Change Assist function operation
in the Driving Assist view on the cluster.
Refer to “View Modes” section in chapter
4.
Highway Lane Change Assist function
will be displayed as below depending on
the status of the function.
„Ready/Operating „Standby/Canceled
OJWEV071312EOJWEV071313E
(1) Highway Lane Change Assist
indicator
[ Green
on : Ready state
[ Green
blink : Operating state
[ Grey
on : Standby state
[ White
blink : Canceled state
(display only a certain time)
(2) Green lane line
The green lane line is displayed when
the function starts operating, and until
the vehicle steps on the lane line.(3) Green arrow and shade
The green arrow is displayed when a
certain amount of time has passed
after the function has started
operating, and until the lane change
has completed.
(4) Message
[ Message is displayed when the
function does not operate even
though the turn signal lever is used.
[ Message is displayed when
the function is cancelled while
operating.
Page 522 of 690
7-108
Driver Assistance System
OJWEV071270L
7 R W X U Q R Q + L J K Z D \ / D Q H & K D Q J H $ V V L V W
Highway Lane Change Assist function
will turn on when the following
conditions are satisfied.
[ The Driving Assist button or Lane
Driving Assist button is used to turn
on Highway Driving Assist.
[ The OK button is pressed on the
steering wheel while a message
asking to use Highway Lane Change
Assist is displayed on the cluster.
+ L J K Z D \ / D Q H & K D Q J H $ V V L V W U H D G \ W R
operate
While Highway Lane Change Assist
function is on, the function will be
ready to operate when all the following
conditions are satisfied:
[ Highway Driving Assist is operating
[ Lane Following Assist is operating
[ A vehicle in the rear area of your
vehicle is detected more than once
after the vehicle is turned on
[ Your vehicle speed is above 50 mph
(80 km/h)
[ Hands-off warning is not displayed on
the cluster
[ Hazard warning flasher is off
Information
[ While Lane Change Assist function
is turned on (indicator on), Lane
Following Assist will not cancel even
if the turn signal indicator or hazard
warning flasher is operating.
[ Lane Change Assist function turns
off automatically when driven in the
following road conditions:
-One driving lane
-A road with a intersection or
crosswalk ahead
-A road with no structure, such as a
medium strip, guardrails, etc.
-There is a pedestrian or cyclist on the
road ahead
[ When the function is in the ready state,
and vehicle speed is below 45 mph (75
km/h), the function will change to the
standby state.
: $ 5 1 , 1 *
: K H Q + L J K Z D \ / D Q H & K D Q J H $ V V L V W
I X Q F W L R Q W X U Q V R I I Z K L O H R S H U D W L Q J
V W H H U L Q J D V V L V W Z L O O E H W H P S R U D U L O \
F D Q F H O O H G $ O Z D \ V E H F D X W L R X V Z K L O H
G U L Y L Q J
Page 529 of 690
7-115
07
Camera settings
OJWEV071214N
You can change Rear View Monitor
‘Display Contents’ by touching the setup
icon (
) on the screen while Rear View
Monitor is operating, or selecting ‘Driver
$ V V L V W D Q F H
Page 532 of 690
7-118
Driver Assistance System
Rear Top View
OJWEV071351N
Rear Top View shows the rear top view
of your vehicle when parking for you to
check the distance between an object
and behind the vehicle.
Rear Top View will turn on under the
following conditions:
[ The gear is shifted to R (Reverse) and
is selected among the view buttons
(3).
[ The Parking/View button (1) is
pressed, while the gear is in P (Park),
N (Neutral) or D (Drive), and vehicle
speed is 6 mph (10 km/h) or less.
Rear Top View will turn off under the
following conditions:
[ The gear is shifted to P (Park).
[ The Parking/View button (1) is
pressed.
[ The infotainment system button (2) is
pressed.
[ The Home button (4) is pressed.
[ The gear is in N (Neutral) or D (Drive)
when vehicle speed is above 10 km/h
(6 mph).
Information
[ The rear views do not turn off when the
gear is in R (Reverse).
[ When the Rear View Monitor is turned
on, the previous view mode will be
displayed. However, if the gear is in
R (Reverse), the rear view will be
displayed.
[ The rear parking guide lines appear
when using Top View and Rear Top
View.
Page 533 of 690
7-119
07
5 H D U 9 L H Z 0 R Q L W R U P D O I X Q F W L R Q
and limitations
Rear View Monitor malfunction
When Rear View Monitor is not working
properly, or the screen flickers, or the
camera image does not display properly,
have the vehicle be inspected by an
authorized retailer of Genesis Branded
products.
: $ 5 1 , 1 *
[ 7 K H U H D U Y L H Z F D P H U D G R H V Q R W
F R Y H U W K H F R P S O H W H D U H D E H K L Q G W K H
Y H K L F O H 7 K H G U L Y H U V K R X O G D O Z D \ V
F K H F N W K H U H D U D U H D G L U H F W O \ W K U R X J K
W K H L Q V L G H D Q G V L G H Y L H Z P L U U R U
E H I R U H S D U N L Q J R U E D F N L Q J X S
[ 7 K H L P D J H V K R Z Q R Q W K H V F U H H Q P D \
differ from the actual distance of the
R E M H F W 0 D N H V X U H W R G L U H F W O \ F K H F N
W K H Y H K L F O H
V V X U U R X Q G L Q J V I R U V D I H W \
[ $ O Z D \ V N H H S W K H U H D U Y L H Z F D P H U D
O H Q V F O H D Q , I W K H O H Q V L V F R Y H U H G Z L W K
I R U H L J Q P D W H U L D O L W P D \ D G Y H U V H O \
affect camera performance and
5 H D U 9 L H Z 0 R Q L W R U P D \ Q R W R S H U D W H
S U R S H U O \ + R Z H Y H U G R Q R W X V H
F K H P L F D O V R O Y H Q W V V X F K D V V W U R Q J
detergents containing high alkaline
R U Y R O D W L O H R U J D Q L F V R O Y H Q W V J D V R O L Q H
D F H W R Q H H W F 7 K L V P D \ G D P D J H W K H
F D P H U D O H Q V