lock GMC ACADIA 2007 Owner's Manual

To continue changing the at tire, seeRemoving
the Flat Tire and Installing the Spare Tire on
page 463.
If the spare tire will not lower, the secondary latch
could be engaged.Do the following to check the cable:
1. Check under the vehicle to see if the cable is
visible.
2. If it is not visible, seeSecondary Latch
System on page 468.
If it is visible, rst try to tighten the cable by
turning the lug wrench clockwise until you hear
two clicks or feel it skip twice. You cannot
over-tighten the cable.
3. Loosen the cable by turning the wrench
counterclockwise three or four turns.
4. If the spare tire has not lowered, tighten the
cable all the way and then loosen it at least
two times.
If the spare tire did lower to the ground,
continue with Step 5 under “Removing the
Spare Tire (Vehicles with the Rear
Convenience Center)” listed previously.
5. If you still cannot lower the spare tire to the
ground, seeSecondary Latch System on
page 468.
462

Removing the Flat Tire and
Installing the Spare Tire
1. It is recommended that you do a safety check
before preceding. SeeChanging a Flat Tire
on page 458for more information.
2. If the vehicle has a wheel cover, loosen the
plastic nut caps with the wheel wrench.
They will not come off. Then, using the at
end of the wheel wrench, pry along the edge
of the cover until it comes off. Be careful;
the edges may be sharp. Do not try to remove
the cover with your bare hands.
Store the wheel cover securely in the rear of
the vehicle until you have the at tire
repaired or replaced.
If your vehicle has aluminum wheels, remove
the wheel nut caps using the wheel wrench.3. Loosen the wheel nuts — but do not
remove them — using the lug wrench.
For wheels with a wheel lock key, use the
wheel lock key between the lock nut and
lug wrench. The key is supplied in the front
passenger door pocket.
Notice:If your vehicle has wheel locks and an
impact wrench is used to remove the wheel
nuts, the lock nut or wheel lock key could be
damaged. Do not use an impact wrench to
remove the wheel nuts if your vehicle has
wheel locks.
463

{CAUTION:
Raising your vehicle with the jack
improperly positioned can damage the
vehicle and even make the vehicle fall.
To help avoid personal injury and vehicle
damage, be sure to t the jack lift head
into the proper location before raising
the vehicle.
6. Attach the lug wrench to the jack, and turn
the wrench clockwise to raise the jack head
3 inches (7.6 cm).
7. Place the jack under the vehicle as identied
in Step 3. Raise the vehicle by turning the
lug wrench clockwise in the jack. Raise
the vehicle far enough off the ground so that
there is enough room for the spare tire to
t under the wheel well.
8. Remove all the wheel nuts and take off the
at tire.9. Remove the plastic spare tire heat shield by
pulling the rubber latch. Store the plastic
spare tire heat shield. SeeStoring a Flat or
Spare Tire and Tools on page 472for
more information.
465

{CAUTION:
Rust or dirt on the wheel, or on the parts
to which it is fastened, can make the
wheel nuts become loose after time.
The wheel could come off and cause an
accident. When changing a wheel, remove
any rust or dirt from the places where the
wheel attaches to the vehicle. In an
emergency, a cloth or a paper towel can
be used to do this; but be sure to use a
scraper or wire brush later, if needed,
to get all the rust or dirt off.
{CAUTION:
Never use oil or grease on studs or nuts.
Because the nuts might come loose.
The vehicle’s wheel could fall off, causing
a serious accident.
10. Remove any rust or
dirt from the wheel
bolts, mounting
surfaces, and spare
wheel.
11. Install the compact spare tire.
12. Lower the vehicle by attaching the lug wrench
to the jack and turning the wrench
counterclockwise. Lower the jack completely.
466

To release the spare tire from the secondary latch:
{CAUTION:
Someone standing too close during the
procedure could be injured by the jack.
If the spare tire does not slide off the jack
completely, make sure no one is behind
you or on either side of you as you pull
the jack out from the under spare.
1. If the cable is not visible, start this procedure
at Step 3.
2. Turn the lug wrench counterclockwise until
approximately 6 inches (15 cm) of cable is
exposed.
All-Wheel-Drive Vehicle shown
469

3. Attach the lug wrench to the jack and raise
the jack at least 10 turns.
4. Place the jack under the vehicle, ahead of the
rear bumper. Position the center lift point of
the jack under the center of the spare tire.
5. Turn the lug wrench clockwise to raise the
jack until it lifts the secondary latch spring.6. Keep raising the jack until the spare tire stops
moving upward and is held rmly in place.
This lets you know that the secondary
latch has released and the spare tire is
balancing on the jack.
7. Lower the jack by turning the lug wrench
counterclockwise. Keep lowering the jack
until the spare tire slides off the jack.
Front-Wheel-Drive Vehicle shown
470

8. Disconnect the lug wrench from the jack and
carefully remove the jack. Use one hand to
push against the spare tire while rmly pulling
the jack out from under the spare tire with
the other hand.9. Tilt the retainer and slip it through the wheel
opening when the spare tire has been
completely lowered.
10. Turn the lug wrench clockwise to raise the
cable back up if the cable is hanging.
Have the hoist assembly inspected as soon as
you can. You will not be able to store a spare tire
using the hoist assembly until it has been
repaired or replaced.
471

Storing the Tools
A. Tool Bag
B. Wing Bolt
C. JackPut back all tools as they were stored in the jack
storage compartment and put the compartment
cover back on.
1. Make that the bottom of the jack is facing
toward you.
2. Turn the jack (C) on its side and place it down
on the holding bracket.
3. Reinstall the wing bolt (B) by turning it
clockwise.
4. To replace the cover, line up the tabs on the
bottom of the cover with the slots in the cover
opening. Push the cover in place, insuring
that the upper front and rear tabs are in
the opening and push the cover closed. Make
sure that the center latch is fully engaged.
This secures the cover in place.
Store the center cap or the plastic bolt-on wheel
covers until a full size tire is put back on the
vehicle. When you replace the compact spare with
a full-size tire, reinstall the bolt-on wheel covers
or the center cap. Hand-tighten them over
the wheel nuts, using the lug wrench.
476

Windshield Wiper Fuses
The windshield wiper motor is protected by a
circuit breaker and a fuse. If the motor overheats
due to heavy snow or ice, the wiper will stop
until the motor cools. If the overload is caused by
some electrical problem, have it xed.
Power Windows and Other Power
Options
Circuit breakers in the fuse panel protect the
power windows and other power accessories.
When the current load is too heavy, the circuit
breaker opens and closes, protecting the circuit
until the problem is xed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected
from short circuits by a combination of fuses,
circuit breakers and fusible thermal links.
This greatly reduces the chance of res caused by
electrical problems.Look at the silver-colored band inside the fuse.
If the band is broken or melted, replace the fuse.
Be sure you replace a bad fuse with a new
one of the identical size and rating.
If you ever have a problem on the road and do not
have a spare fuse, you can borrow one that has
the same amperage. Just pick some feature
of your vehicle that you can get along without, like
the radio or cigarette lighter, and use its fuse if
it is the correct amperage. Replace it as soon as
you can.
Instrument Panel Fuse Block
The instrument panel fuse block is located under
the instrument panel on the passenger side of
the vehicle. Pull down on the cover to access the
fuse block.
490

Fuses Usage
FRT/WSW Front Windshield Wiper
SPARE Spare
HTD/SEAT Front Heated Seats
STR/WHL/
ILLUMSteering Wheel Illumination
MSM Memory Seat Module
PWR/MIRRORS Power Mirrors
DR/LCK Door Locks
AIRBAG Airbag System
LT/TRN/SIG Driver’s Side Turn Signal
REAR WIPER Rear Window Wiper
PWR MODPassKey Module, Body Control
Module
BCK/UP/STOP Back-up Lamps, Stoplamps
HVAC Climate Control System
DISPLAY Display
RT/TRN/SIG Passenger’s Side Turn Signal
Fuse Side
491