tow GMC C-SERIES 1999 User Guide

yellowblue
2-27
If your vehicle has air
brakes, you will have this
control. Pulling it out
applies the parking brake.
The PARK BRAKE light
will come on when the air
parking brake is applied.
Vehicles built for use as tractors or towing vehicles have
one or two more air brake controls. They look like this:To charge a trailer's air brake system:
1. Move your tractor into the proper position. Apply the
parking brake by pulling the yellow SYSTEM PARK
knob out.
2. Hook up the trailer air system properly.
3. Get into the tractor. Push and hold down the regular
brake pedal.
4. Push in both the yellow SYSTEM PARK and the red
TRAILER AIR SUPPLY knobs. This will charge
your trailer's air system.
If you have the blue TRACTOR PARKING knob,
pull it out to set the tractor brakes while the air system
is charging.
After a few minutes, the trailer system should be fully
charged. When it is, the air pressure gage will show
about 125 to 135 psi (862 to 931 kPa) and you may hear
the ªpop offº valve operate.
For driving with a trailer, the yellow, red and blue
(if equipped) knobs all must be pushed in. It's the same
when you're not pulling a trailer except that the red
TRAILER AIR SUPPLY knob must be out.
ProCarManuals.com

yellowblue
2-28
CAUTION:
If you apply any one of the air brake parking
controls while the vehicle is moving, your rig will
stop suddenly. If you are not ready for this, you
or others could be injured. Don't apply any one
of these controls while you're driving, unless you
have to make an emergency stop.
If the air pressure drops below 60 to 70 psi (413 to
482 kPa), the PRIMARY BRAKE light will come on. If
the air pressure drops to 40 to 45 psi (275 to 309 kPa), the
yellow knob will automatically pop out and apply the
spring brakes. If you ever have a complete loss of air so
that your air brakes automatically apply, there is a way that
the tow operator can release the parking brakes to tow the
vehicle. See ªTowing Your Vehicleº in the Index.
CAUTION:
If your vehicle is left in gear, the engine can
start if the vehicle starts to roll. This can easily
happen if you have the diesel engine. Shift the
transmission into NEUTRAL (N) before you
leave the vehicle.
ProCarManuals.com

yellowblue
2-34
An arrow on the instrument panel will flash in the
direction of the turn when the lever is in the up or
down position.
This system replaces the turn signal feature of the
multifunction lever only. All other features such as
headlamp high/low beam, windshield wipers and
washer, etc. remain part of the multifunction system.
If you have this system, see ªSignal
-Stat Turn Signal
and Hazard Warning Flasherº in the Index to find out
how the hazard warning flasher portion works.
Headlamp High/Low Beam Changer
To change the headlamps from low beam to high, push
the multifunction lever away from you. To switch back
to low beam, pull the lever toward you.
When the high beams are
on, a light on the instrument
cluster will also be on.
Windshield Wipers
The windshield wipers are controlled by turning the
band with the wiper symbol on it.
For a single wiping cycle, turn the band to MIST. Hold
it there until the wipers start, then let go. The wipers will
stop after one cycle. If you want more cycles, hold the
band on MIST longer.
For steady wiping at low speed, turn the band away
from you to the LO position. For fast wiping, turn the
band to HI. To stop the wipers, turn the band to the
off symbol.
ProCarManuals.com

yellowblue
2-46
Interior Lamps
Dome Lamp
The dome lamps will come on when you open the
driver's door. You can also turn the dome lamps on by
turning the interior lamp dimmer dial all the way up
until it clicks.
Mirrors
Inside Rearview Mirror (If Equipped)
Press the tab under the mirror to reduce glare at night
from headlamps behind you.
Outside Mirrors
Adjust the outside mirror or
mirrors by hand so you can
just see the side of your
vehicle when you're sitting
in the driver's seat. These
mirrors can fold in toward
the vehicle for entering
narrow garages and for
clearance in an automatic
vehicle wash.
If your mirrors have the clearance lamps, they'll be on
when your parking lamps are on.
Convex Outside Mirrors (Option)
Your vehicle may have optional convex mirrors. A
convex mirror's surface is curved so you can see more
from the driver's seat.
CAUTION:
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right or left lane,
you could hit a vehicle. Check your regular
outside mirrors (or your inside mirror, if you
have one) before changing lanes.
ProCarManuals.com

yellowblue
2-57
Readings in the low warning zone may occur when a
large number of electrical accessories are operating
in the vehicle and the engine is left at an idle for an
extended period. This condition is normal since the
charging system may not be able to provide full
power at engine idle. As engine speeds are increased,
this condition should correct itself because higher
engine speeds allow the charging system to create
maximum power.
You can only drive a short time on the battery. Be sure
to shut off the radio, the fan or any unnecessary
accessories and have the system serviced.
Do Not Shift Warning Light
If your vehicle has the
Allison MD automatic
transmission, certain
transmission malfunctions
will turn this light on.If this light comes on while you are driving, do not use
the transmission shift control. Using the transmission
shift control will result in the loss of forward gears. The
computer for the transmission senses a problem and
chooses a gear to stay in so that you can drive the
vehicle in that gear. You may not be able to drive as fast
or back up when this light is on.
NOTICE:
If the DO NOT SHIFT warning light comes on
while you are driving, it is a warning that making
a transmission ªrangeº change could leave you
stranded. The vehicle may not continue to move
if you change gears with the transmission shift
control. The transmission can't operate in all
gears because something is wrong. Leave the shift
control alone and drive directly to a GM dealer
for service. If you can't go in for service
immediately, have the vehicle towed.
Brake System Warning Light
Your vehicle has either hydraulic or air brakes. Each
system has different warning lights.
ProCarManuals.com

yellowblue
2-58
Hydraulic Brake System Warning Lights
Vehicles with hydraulic systems have two brake system
warning lights on the instrument panel.
If the PRIMARY BRAKE
warning light comes on, it
means that the fluid level in
the master cylinder
reservoir is low or there is
another problem with your
primary hydraulic brakes.
When it comes on, you will also hear a warning tone.
The PRIMARY BRAKE warning light may come on,
and the warning tone may sound, when you're turning
and braking at the same time. This is normal. See
ªHydraulic Brake Systemsº in the Index.
If the AUX BRAKE
warning light comes on, it
means that there is
something wrong in the
auxiliary brake system.
When this light comes on, you will also hear a warning tone.Both of these lights should come on briefly every time
you start the engine. If they don't come on then, have
them fixed so they will be ready to warn you if there's a
problem. If one or both of these warning lights stay on
after you start the engine, there could be a brake
problem. Have your brake system inspected right away.
If one or both of these lights come on and stay on while
you are driving, pull off the road and stop carefully. You
may notice that the pedal is harder to push. Or, the pedal
may go closer to the floor. It may take longer to stop.
If either light is still on, have the vehicle towed for
service. (See ªTowing Your Vehicleº in the Index.)
See ªHydraulic Brake Systemsº in the Index for
more information.
CAUTION:
Your brake system may not be working properly
if a brake system warning light is on. Driving
with either of the brake system warning lights on
can lead to an accident. If either light is still on
after you've pulled off the road and stopped
carefully, have the vehicle towed for service.
ProCarManuals.com

yellowblue
2-64 Service Trans Filter Indicator Light
(If Equipped)
If your vehicle has this
light, you'll find it
below the cluster on the
instrument panel.
It monitors the transmission fluid filter. If it ever
goes on, it means your transmission filter is dirty and
requires replacement.
Malfunction Indicator Lamp
(Check Engine Light)
If your vehicle is equipped
with either a gasoline
engine or an electronically
controlled diesel engine,
you will have this light.
If this light comes on or flashes while you are driving,
two things may happen.
First, you won't notice any difference in engine
performance, but your tail pipe emissions may increase.
Second, your engine may not run properly or may stall
without warning. If either of these things happen, drive
or tow your vehicle to your dealer for service.
ProCarManuals.com

yellowblue
3-2
Comfort Controls
Standard Comfort Controls
If your vehicle does not have air conditioning, this is
what your comfort controls will look like.
Function Lever
The top lever can be moved to three different heating
functions. If you place the lever between positions, it
will send air out both vents.
VENT: The air comes out at the vents on your
instrument panel and at your front side windows.
HEATER: Heated air comes out near the floor.
This is the best setting for cold weather.
DEFOG: This setting operates the defogger.
Heated air comes out near the windshield. Use this when
fog or ice is on the windshield.
Temperature Lever
The bottom lever lets you select the temperature of the
air flowing into your vehicle. Move the lever to the plus
symbol for warmer air. Move the lever to the minus
symbol for cooler air.
If your engine is equipped with an engine coolant heater,
you can use it during initial start
-up in cold weather
(20
F (
-8
C) or lower) to help heat the passenger
compartment faster. See ªEngine Coolant Heaterº in
the Index.
Fan Knob
The fan knob has four positions. To increase airflow,
turn the knob toward the plus symbol. To decrease
airflow, turn it toward the minus symbol.
ProCarManuals.com

yellowblue
3-4
Left Blend Button
The airflow can be blended between the two positions.
To blend between the positions, press the side of the
button showing the area where you would like more
airflow. The system will automatically begin to blend
toward the position chosen. To stop the system between
positions, just press the same side of the button again.
VENT: Press the top of the button and all of the
airflow will come through the instrument panel vents.
HEATER: Press the bottom of this button and all
of the airflow will come through the floor outlet.
Right Blend Button
The airflow can be blended between the two positions.
To blend between positions, press the side of the button
showing the area where you would like more airflow.
The system will automatically begin to blend toward the
position chosen. To stop the system between positions,
just press the same side of the button again.
DEFOG: This setting operates the defogger. Air
comes out near the bottom of the windshield and at your
front side windows.
HEATER: Press the bottom of this button and
heated air comes out near the floor.A/C Button
Press the A/C button to turn your air conditioner on and
off. The A/C symbol will light on your display, and air
will come out of your instrument panel vents. The fan
will automatically be set on LOW.
MAX Button
If you press the MAX button, the air in your vehicle will
be recirculated. With the air conditioner on, MAX will
give you maximum cooling. It can also be used in all
modes to help keep dust out of your vehicle. When
MAX is selected, REC will light on the display.
Fan Control Button
This button is in the upper passenger's side corner of
your system control panel. The fan has four settings:
low, medium low, medium high and high. Press the top
of the button with the plus symbol to increase airflow.
Press the bottom of the button with the minus symbol to
decrease airflow. The setting you select is shown on
your display as LOW, MED, HI or OFF.
ProCarManuals.com

yellowblue
3-5
OFF
Press this button to turn the air conditioning/heating
system off. Pressing OFF will erase the present mode of
operation from the system's memory. Outside air will
still come out of the heater outlet whenever the vehicle
is moving forward.
If the OFF button is pressed, you must press A/C,
MAX or one of the BLEND buttons to turn the system
back on.
Air Conditioning
When you first turn on your vehicle's air conditioning,
open the windows long enough to clear the vehicle of
hot air, then close them. Using the MAX button can also
help. See ªMAX Buttonº earlier in this section for
more information.
For normal cooling on hot days, use A/C with the
temperature selector toward C.
When you press the A/C button to turn the air
conditioner off, the system will operate in the vent
mode. When you turn the air conditioner back on, the
system will operate in the mode you last selected unless
the OFF button was pressed.If your air conditioner develops high system pressure, it
will automatically go into the MAX mode and REC will
light on your display. The A/C system will remain in the
MAX mode, even if you press the MAX button, until
system pressure returns to a normal level.
Heating
On cold days, use HEATER with the temperature
selector all the way toward H. When the inside of the
vehicle has reached a comfortable temperature, maintain
it by using the temperature selector bar.
If your vehicle is equipped with a diesel engine, and the
engine has been idling for a long time when it's cold
outside, your heater may blow out cool air. This is
normal. When you increase the engine speed under load,
your heater should blow out warmer air. If it doesn't,
your coolant level may be low. See ªEngine Coolantº in
the Index to check your coolant level.
While idling your diesel engine, you can use the MAX
button to recirculate the air in the cab to help maintain
interior heat. This will preserve engine coolant temperature
and cab heat when idling cannot be avoided.
Using the MAX button while driving is not recommended
because interior window fogging can result.
ProCarManuals.com